SYSTem:RMODule:RESet

34980A

SYSTem:RMODule:RESet

Syntax

SYSTem:RMODule:RESet <slot>

Description

This command resets all 34945EXT remote modules connected to the 34945A Microwave Switch/Attenuator Driver in the specified slot. This command provides the only way to reset all 34945EXT remote modules in a given slot to a factory default state. The following table shows the reset state.  

Attribute

Reset State

At the 34945EXT Level:

 

 

ROUTe:RMODule:DRIVe:SOURce[:IMMediate]

OFF

 

ROUTe:RMODule:DRIVe:SOURce:BOOT

OFF

 

ROUTe:RMODule:DRIVe:LIMit

1

At the Bank Level:

 

 

ROUTe:RMODule:BANK:DRIVe[:MODE]

OCOLlector

 

ROUTe:RMODule:BANK:LED:DRIVe[:ENABle]

ON

 

ROUTe:RMODule:BANK:LED:DRIVe:LEVel

5 mA

All Channels:

 

 

ROUTe:CHANnel:DRIVe:PAIRed[:MODE]

OFF

 

ROUTe:CHANnel:DRIVe:PULSe[:MODE]

ON

 

ROUTe:CHANnel:DRIVe:PULSe:WIDTh

15 ms

 

ROUTe:CHANnel:DRIVe:TIME:RECovery

0.0 seconds

 

ROUTe:CHANnel:DRIVe:TIME:SETTle

0.0 seconds

 

ROUTe:CHANnel:DRIVe:OPEN:DEFault

OPEN selected

 

ROUTe:CHANnel:VERify[:ENABle]

OFF

 

ROUTe:CHANnel:VERify:POLarity

NORMal

 

Used With:

  • 34945A Microwave Switch/Attenuator Driver

Parameters

Name

Type

Range of Values

Default Value

<slot>

Discrete

{1|2|3|4|5|6|7|8}

This is a required parameter

Remarks

  • Since this command disables both the channel drive source and channel drive boot state, the channels will remain inoperable until you re-enable the channel drive source using the ROUTe:RMODule:DRIVe:SOURce[:IMMediate] command (select the INTernal or EXTernal source).

  • With the SYSTem:RMODule:RESet command, the bank-level attributes are reset without regard to which distribution boards are installed. To reset the bank-level attributes on a specific 34945EXT remote module, see the ROUTe:RMODule:BANK:PRESet command; with this command, the bank-level attributes vary according to which distribution boards are installed.

  • The *RST and SYSTem:PRESet commands reset all channels on a remote module to their default states as specified by the ROUTe:CHANnel:DRIVe:OPEN:DEFault command and set all channel drives to the specified boot state (see ROUTe:RMODule:DRIVe:SOURce:BOOT command). In addition, when the *RST and SYSTem:PRESet commands are executed, the 34945A automatically re-evaluates all external remote module connections to determine what is connected, what is powered, etc. No other settings are changed.

  • The SYSTem:CPON command has nearly the same effect as the *RST and SYSTem:PRESet commands (see above). However, when the SYSTem:CPON command is executed, the 34945A does not re-evaluate the external remote module connections.

  • The SYSTem:RMODule:RESet command does not clear the relay cycle count on the specified slot (see DIAGnostic:RELay:CYCLes? command).

Example

The following command resets all 34945EXT remote modules connected to slot 3 to their factory default state. The bank-level attributes are reset without regard to which distribution boards are installed.

SYST:RMOD:RESET 3

See Also

*RST

DIAGnostic:RELay:CYCLes?

ROUTe:RMODule:BANK:PRESet

SYSTem:CPON

SYSTem:PRESet