National Instruments Interface Cards

WinWCP V5.3.8

Getting Started > Laboratory Interfaces > National Instruments Interface Cards

National Instruments Inc. (www.ni.com)

 

WinWCP is compatible with most National Instruments multifunction data acquisition cards or devices, including M, X, and E series cards, the Lab-PC/1200 series and USB devices. The PCI-6221 PCI card (with BNC-2110 I/O box and 2m SHC68-68-EPM cable) or the USB-6341 (with BNC connectivity) device is currently recommended.

The National Instruments NIDAQ interface library must be installed before WinWCP can use the interface card. Most modern cards (X, M and E series) are supported via the NIDAQ-MX library. Older cards (Lab-PC/1200 series) require the ‘Traditional’ NIDAQ library (V4.9 or earlier) to be installed. WinWCP supports both types of library.

Software installation

1)      Install the NIDAQ library from the disks supplied with interface card, following the instructions supplied by National Instruments.

2)      Install the interface card in an expansion slot (or attach a USB device).

3)      Reboot the computer.

4)      Run National Instruments’ Measurement & Automation Explorer program. You should find the card listed under Devices & Interfaces.  Note the Device number (Dev1, Dev2 etc.) of the card.

5)      Right-click over the device and select Self Test to check that the device is functioning correctly.

6)      If the tests check out OK, run WinWCP and select from the main menu

Setup
Laboratory Interface

to open the Laboratory Interface Setup dialog box




then select National Instruments (NIDAQ-MX) from the list of laboratory interface options (except for Lab-PC or 1200 series cards in which case use National Instruments (NIDAQ Trad)).

7)      Select the device number of the card listed in the NI Devices & Interfaces list from the Device list (usually Dev1 if only one card is installed).
 

8)      Set the A/D Input mode. If you are using a BNC-2110 or BNC-2090 input/output box, select Differential.  (Note. The SE/DI switches on a BNC 2090 panel must be set to DI ) If you are using a Lab-PC or 1200 series card, set the A/D Input mode to Single Ended (RSE).

 

 

Signal input / output connections

Signal input and output from National Instruments PCI cards are made via 68 pin sockets on the rear of the card attached to BNC socket input/output panels (BNC-2110 or BNC-2090 ) or screw terminal panels by appropriate shielded cables available from National Instruments.


 

National Instruments X, E & M Series cards

National Instruments X, E & M Series cards

Analog Input

I/O Panel

Screw terminal panel

Ch. 0

ACH0

68, 67+62 (signal,ground)

Ch. 1

ACH1

33, 67+62

Ch. 2

ACH2

65, 67+62

Ch. 3

ACH3

30, 67+62

Ch. 4

ACH4

28, 67+62

Ch. 5

ACH5

60, 67+62

Ch. 6

ACH6

25, 67+62

Ch. 7

ACH7

57, 67+62

Analog Output

 

 

Ch. 0

DACOUT 0

22,55

Ch. 1

DACOUT 1

21,55

Trigger Inputs

 

 

Ext. Sweep Trigger

PFI0/TRIG1

11,44

Ext. Stimulus Trigger

PFI0/TRIG1 (NIDAQ-MX)
PFI1/TRIG2 (NIDAQ)

11,44 (See Note 1)
10.44

Digital Output

 

 

Ch. 0

DIO0

52,53

Ch. 1

DIO1

17,53

Ch. 2

DIO2

49,53

Ch. 3

DIO3

47,53

Ch. 4

DIO4

19,53

Ch. 5

DIO5

51,53

Ch. 6

DIO6

16,53

Ch. 7

DIO7

48,53


Note 1. An active-high TTL pulse on this input triggers the start a stimulus program which has been set up with the External Stimulus Trigger = Y option. The trigger signal is applied to PFI0 when the NIDAQ-MX interface library is in use (Laboratory Interface Card = National Instruments (NIDAQ-MX) and PFI1 when the Traditional NIDAQ interface library (for Lab-PC/1200 cards only) is in use (Laboratory Interface Card = National Instruments (NIDAQ)

USB-6000 to USB-6005 Devices

 

The input/output connections for the low cost USB 6000-6005 devices are

 

USB 6000-6005

Analog Inputs

Screw terminal panel

Ch. 0

AI +0, -0 (signal, ground) 

Ch. 1

AI +1, -1 (signal, ground) 

Ch. 2

AI +2, -2 (signal, ground) 

Ch. 3

AI +3, -3 (signal, ground) 

Analog Outputs

 

Ch. 0

AO 0, Gnd (signal, ground) 

Ch. 1

AO 1, Gnd (signal, ground) 

Trigger Inputs

 

Ext. Sweep Trigger

PFI0,Gnd (signal, ground) 

Ext. Stimulus Trigger

PFI0+PFI1,Gnd (signal, ground) 

 

 

Note.

PFI0, PFI1 and P1.0 MUST be connected together for Stimulus Protocols to be produced and the test pulse to generated in the Seal Test window.

Digital Stimulus protocols are not supported by these devices.


 

Lab-PC/1200 Series Cards

 

The input/output connections for 50 pin Lab-PC and 1200- series boards are tabulated below.

 

Lab-PC/1200 Cards

Analog Inputs

I/O Panel

Screw terminal panel

Ch. 0

ACH0

1,9 (signal,ground)

Ch. 1

ACH1

2,9

Ch. 2

ACH2

3,9

Ch. 3

ACH3

4,9

Ch. 4

ACH4

5,9

Ch. 5

ACH5

6,9

Ch. 6

ACH6

7,9

Ch. 7

ACH7

8,9

Analog Outputs

 

 

Ch. 0

DAC 0

10,11

Ch. 1

DAC 1

12,11 (See Note 1)

Trigger Inputs

 

 

Ext. Sweep Trigger

EXTTRIG

38,50 (See Note 1)

Ext. Stimulus Trigger

PB7

29,50 (See Note 2)

Digital Synch. Input

PC6

36, 13 (See Note 1)

Digital Outputs

 

 

Ch. 0

PA0

14,13

Ch. 1

PA1

15,13

Ch. 2

PA2

16,13

Ch. 3

PA3

17,13

Ch. 4

PA4

18,13

Ch. 5

PA5

19,13

Ch. 6

PA6

20,13

Ch. 7

PA7

21,13


NOTE 2 Analog output channel 1 (DAC1) is used to synchronise the start of the A/D conversion and D/A waveform generation and must be connected to EXTTRIG for WinWCP waveform generation functions to operate. In addition, if stimulus protocols containing digital ouputs are required DAC1 & EXTTRIG must also be connected to the digital synchronisation input PC6.

Note. 2. Lab-PC/1200 series boards need the pulse to be 10 ms in duration or longer.

Troubleshooting

National Instruments cards can be used with a number of different types of input/output panels ( BNC 2090, BNC 2110 or CB-68 terminal panel) and can also be configured to handle the analog input channels in a number of different ways (differential, referenced single ended and non-referenced single ended). Some combinations of settings can lead to input signals drifting or going off scale.

 

Differential mode (DIFF): Analog input channels are paired together and subtracted (e.g. Ch.0 – Ch.7, Ch.1 – Ch.8 etc.).

 

Referenced single ended mode (RSE): Analog input channels are used individually and measured relative to signal ground of the computer.

 

Non-referenced single ended mode (NRSE): Analog input channels are used individually and measured relative to the electrical ground of the device being measured.

 

When using the BNC-2110 I/O box, the USB-6221-BNC or USB-6229-BNC USB interface device the WinWCP A/D Input Mode must be set at Differential.

 

When using the BNC-2090 I/O box with its SE/DI switches set to DI (the default setting) the WinWCP A/D Input Mode should be set to Differential.

 

When using the BNC-2090 I/O box with its SE/DI switches set to SE and the RSE/NRSE switch set to NRSE the WinWCP A/D Input Mode should be set at Single Ended (NRSE)