 |
X-CUBE-SPN11 for X-NUCLEO-IHM11M1
|
HAL configuration file. More...
#include "stm32f4xx_hal_rcc.h"
#include "stm32f4xx_hal_gpio.h"#include "stm32f4xx_hal_dma.h"#include "stm32f4xx_hal_cortex.h"#include "stm32f4xx_hal_adc.h"#include "stm32f4xx_hal_flash.h"#include "stm32f4xx_hal_pwr.h"#include "stm32f4xx_hal_spi.h"#include "stm32f4xx_hal_tim.h"#include "stm32f4xx_hal_uart.h"Go to the source code of this file.
Macros | |
| #define | HAL_MODULE_ENABLED |
| This is the list of modules to be used in the HAL driver. More... | |
| #define | HAL_ADC_MODULE_ENABLED |
| #define | HAL_SPI_MODULE_ENABLED |
| #define | HAL_TIM_MODULE_ENABLED |
| #define | HAL_UART_MODULE_ENABLED |
| #define | HAL_GPIO_MODULE_ENABLED |
| #define | HAL_DMA_MODULE_ENABLED |
| #define | HAL_RCC_MODULE_ENABLED |
| #define | HAL_FLASH_MODULE_ENABLED |
| #define | HAL_PWR_MODULE_ENABLED |
| #define | HAL_CORTEX_MODULE_ENABLED |
| #define | HSE_VALUE ((uint32_t)8000000) |
| Adjust the value of External High Speed oscillator (HSE) used in your application. More... | |
| #define | HSE_STARTUP_TIMEOUT ((uint32_t)5000) |
| #define | HSI_VALUE ((uint32_t)16000000) |
| Internal High Speed oscillator (HSI) value. More... | |
| #define | LSI_VALUE ((uint32_t)32000) |
| Internal Low Speed oscillator (LSI) value. More... | |
| #define | LSE_VALUE ((uint32_t)32768) |
| External Low Speed oscillator (LSE) value. More... | |
| #define | EXTERNAL_CLOCK_VALUE ((uint32_t)12288000) |
| External clock source for I2S peripheral This value is used by the I2S HAL module to compute the I2S clock source frequency, this source is inserted directly through I2S_CKIN pad. More... | |
| #define | VDD_VALUE ((uint32_t)3300) |
| This is the HAL system configuration section. More... | |
| #define | TICK_INT_PRIORITY ((uint32_t)2) |
| #define | USE_RTOS 0 |
| #define | PREFETCH_ENABLE 1 |
| #define | INSTRUCTION_CACHE_ENABLE 1 |
| #define | DATA_CACHE_ENABLE 1 |
| #define | MAC_ADDR0 2 |
| Uncomment the line below to expanse the "assert_param" macro in the HAL drivers code. More... | |
| #define | MAC_ADDR1 0 |
| #define | MAC_ADDR2 0 |
| #define | MAC_ADDR3 0 |
| #define | MAC_ADDR4 0 |
| #define | MAC_ADDR5 0 |
| #define | ETH_RX_BUF_SIZE ETH_MAX_PACKET_SIZE /* buffer size for receive */ |
| #define | ETH_TX_BUF_SIZE ETH_MAX_PACKET_SIZE /* buffer size for transmit */ |
| #define | ETH_RXBUFNB ((uint32_t)4) /* 4 Rx buffers of size ETH_RX_BUF_SIZE */ |
| #define | ETH_TXBUFNB ((uint32_t)4) /* 4 Tx buffers of size ETH_TX_BUF_SIZE */ |
| #define | DP83848_PHY_ADDRESS 0x01 |
| #define | PHY_RESET_DELAY ((uint32_t)0x000000FF) |
| #define | PHY_CONFIG_DELAY ((uint32_t)0x00000FFF) |
| #define | PHY_READ_TO ((uint32_t)0x0000FFFF) |
| #define | PHY_WRITE_TO ((uint32_t)0x0000FFFF) |
| #define | PHY_BCR ((uint16_t)0x00) |
| #define | PHY_BSR ((uint16_t)0x01) |
| #define | PHY_RESET ((uint16_t)0x8000) |
| #define | PHY_LOOPBACK ((uint16_t)0x4000) |
| #define | PHY_FULLDUPLEX_100M ((uint16_t)0x2100) |
| #define | PHY_HALFDUPLEX_100M ((uint16_t)0x2000) |
| #define | PHY_FULLDUPLEX_10M ((uint16_t)0x0100) |
| #define | PHY_HALFDUPLEX_10M ((uint16_t)0x0000) |
| #define | PHY_AUTONEGOTIATION ((uint16_t)0x1000) |
| #define | PHY_RESTART_AUTONEGOTIATION ((uint16_t)0x0200) |
| #define | PHY_POWERDOWN ((uint16_t)0x0800) |
| #define | PHY_ISOLATE ((uint16_t)0x0400) |
| #define | PHY_AUTONEGO_COMPLETE ((uint16_t)0x0020) |
| #define | PHY_LINKED_STATUS ((uint16_t)0x0004) |
| #define | PHY_JABBER_DETECTION ((uint16_t)0x0002) |
| #define | PHY_SR ((uint16_t)0x10) |
| #define | PHY_MICR ((uint16_t)0x11) |
| #define | PHY_MISR ((uint16_t)0x12) |
| #define | PHY_LINK_STATUS ((uint16_t)0x0001) |
| #define | PHY_SPEED_STATUS ((uint16_t)0x0002) |
| #define | PHY_DUPLEX_STATUS ((uint16_t)0x0004) |
| #define | PHY_MICR_INT_EN ((uint16_t)0x0002) |
| #define | PHY_MICR_INT_OE ((uint16_t)0x0001) |
| #define | PHY_MISR_LINK_INT_EN ((uint16_t)0x0020) |
| #define | PHY_LINK_INTERRUPT ((uint16_t)0x2000) |
| #define | assert_param(expr) ((void)0) |
| Include module's header file. More... | |
Detailed Description
HAL configuration file.
- Attention
© COPYRIGHT(c) 2015 STMicroelectronics
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:
- Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
- Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
- Neither the name of STMicroelectronics nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
Definition in file stm32f4xx_hal_conf.h.
Macro Definition Documentation
| #define assert_param | ( | expr | ) | ((void)0) |
Include module's header file.
Definition at line 391 of file stm32f4xx_hal_conf.h.
| #define DATA_CACHE_ENABLE 1 |
Definition at line 149 of file stm32f4xx_hal_conf.h.
| #define DP83848_PHY_ADDRESS 0x01 |
Definition at line 179 of file stm32f4xx_hal_conf.h.
| #define ETH_RX_BUF_SIZE ETH_MAX_PACKET_SIZE /* buffer size for receive */ |
Definition at line 171 of file stm32f4xx_hal_conf.h.
| #define ETH_RXBUFNB ((uint32_t)4) /* 4 Rx buffers of size ETH_RX_BUF_SIZE */ |
Definition at line 173 of file stm32f4xx_hal_conf.h.
| #define ETH_TX_BUF_SIZE ETH_MAX_PACKET_SIZE /* buffer size for transmit */ |
Definition at line 172 of file stm32f4xx_hal_conf.h.
| #define ETH_TXBUFNB ((uint32_t)4) /* 4 Tx buffers of size ETH_TX_BUF_SIZE */ |
Definition at line 174 of file stm32f4xx_hal_conf.h.
| #define EXTERNAL_CLOCK_VALUE ((uint32_t)12288000) |
External clock source for I2S peripheral This value is used by the I2S HAL module to compute the I2S clock source frequency, this source is inserted directly through I2S_CKIN pad.
Value of the External audio frequency in Hz
Definition at line 133 of file stm32f4xx_hal_conf.h.
| #define HAL_ADC_MODULE_ENABLED |
Definition at line 51 of file stm32f4xx_hal_conf.h.
| #define HAL_CORTEX_MODULE_ENABLED |
Definition at line 87 of file stm32f4xx_hal_conf.h.
| #define HAL_DMA_MODULE_ENABLED |
Definition at line 83 of file stm32f4xx_hal_conf.h.
| #define HAL_FLASH_MODULE_ENABLED |
Definition at line 85 of file stm32f4xx_hal_conf.h.
| #define HAL_GPIO_MODULE_ENABLED |
Definition at line 82 of file stm32f4xx_hal_conf.h.
| #define HAL_MODULE_ENABLED |
This is the list of modules to be used in the HAL driver.
Definition at line 50 of file stm32f4xx_hal_conf.h.
| #define HAL_PWR_MODULE_ENABLED |
Definition at line 86 of file stm32f4xx_hal_conf.h.
| #define HAL_RCC_MODULE_ENABLED |
Definition at line 84 of file stm32f4xx_hal_conf.h.
| #define HAL_SPI_MODULE_ENABLED |
Definition at line 73 of file stm32f4xx_hal_conf.h.
| #define HAL_TIM_MODULE_ENABLED |
Definition at line 74 of file stm32f4xx_hal_conf.h.
| #define HAL_UART_MODULE_ENABLED |
Definition at line 75 of file stm32f4xx_hal_conf.h.
| #define HSE_STARTUP_TIMEOUT ((uint32_t)5000) |
Time out for HSE start up, in ms
Definition at line 100 of file stm32f4xx_hal_conf.h.
| #define HSE_VALUE ((uint32_t)8000000) |
Adjust the value of External High Speed oscillator (HSE) used in your application.
This value is used by the RCC HAL module to compute the system frequency (when HSE is used as system clock source, directly or through the PLL). Value of the External oscillator in Hz
Definition at line 96 of file stm32f4xx_hal_conf.h.
| #define HSI_VALUE ((uint32_t)16000000) |
Internal High Speed oscillator (HSI) value.
This value is used by the RCC HAL module to compute the system frequency (when HSI is used as system clock source, directly or through the PLL). Value of the Internal oscillator in Hz
Definition at line 109 of file stm32f4xx_hal_conf.h.
| #define INSTRUCTION_CACHE_ENABLE 1 |
Definition at line 148 of file stm32f4xx_hal_conf.h.
| #define LSE_VALUE ((uint32_t)32768) |
External Low Speed oscillator (LSE) value.
< Value of the Internal Low Speed oscillator in Hz The real value may vary depending on the variations in voltage and temperature.Value of the External Low Speed oscillator in Hz
Definition at line 124 of file stm32f4xx_hal_conf.h.
| #define LSI_VALUE ((uint32_t)32000) |
Internal Low Speed oscillator (LSI) value.
Definition at line 116 of file stm32f4xx_hal_conf.h.
| #define MAC_ADDR0 2 |
Uncomment the line below to expanse the "assert_param" macro in the HAL drivers code.
Definition at line 163 of file stm32f4xx_hal_conf.h.
| #define MAC_ADDR1 0 |
Definition at line 164 of file stm32f4xx_hal_conf.h.
| #define MAC_ADDR2 0 |
Definition at line 165 of file stm32f4xx_hal_conf.h.
| #define MAC_ADDR3 0 |
Definition at line 166 of file stm32f4xx_hal_conf.h.
| #define MAC_ADDR4 0 |
Definition at line 167 of file stm32f4xx_hal_conf.h.
| #define MAC_ADDR5 0 |
Definition at line 168 of file stm32f4xx_hal_conf.h.
| #define PHY_AUTONEGO_COMPLETE ((uint16_t)0x0020) |
Auto-Negotiation process completed
Definition at line 204 of file stm32f4xx_hal_conf.h.
| #define PHY_AUTONEGOTIATION ((uint16_t)0x1000) |
Enable auto-negotiation function
Definition at line 199 of file stm32f4xx_hal_conf.h.
| #define PHY_BCR ((uint16_t)0x00) |
Transceiver Basic Control Register
Definition at line 190 of file stm32f4xx_hal_conf.h.
| #define PHY_BSR ((uint16_t)0x01) |
Transceiver Basic Status Register
Definition at line 191 of file stm32f4xx_hal_conf.h.
| #define PHY_CONFIG_DELAY ((uint32_t)0x00000FFF) |
Definition at line 183 of file stm32f4xx_hal_conf.h.
| #define PHY_DUPLEX_STATUS ((uint16_t)0x0004) |
PHY Duplex mask
Definition at line 216 of file stm32f4xx_hal_conf.h.
| #define PHY_FULLDUPLEX_100M ((uint16_t)0x2100) |
Set the full-duplex mode at 100 Mb/s
Definition at line 195 of file stm32f4xx_hal_conf.h.
| #define PHY_FULLDUPLEX_10M ((uint16_t)0x0100) |
Set the full-duplex mode at 10 Mb/s
Definition at line 197 of file stm32f4xx_hal_conf.h.
| #define PHY_HALFDUPLEX_100M ((uint16_t)0x2000) |
Set the half-duplex mode at 100 Mb/s
Definition at line 196 of file stm32f4xx_hal_conf.h.
| #define PHY_HALFDUPLEX_10M ((uint16_t)0x0000) |
Set the half-duplex mode at 10 Mb/s
Definition at line 198 of file stm32f4xx_hal_conf.h.
| #define PHY_ISOLATE ((uint16_t)0x0400) |
Isolate PHY from MII
Definition at line 202 of file stm32f4xx_hal_conf.h.
| #define PHY_JABBER_DETECTION ((uint16_t)0x0002) |
Jabber condition detected
Definition at line 206 of file stm32f4xx_hal_conf.h.
| #define PHY_LINK_INTERRUPT ((uint16_t)0x2000) |
PHY link status interrupt mask
Definition at line 222 of file stm32f4xx_hal_conf.h.
| #define PHY_LINK_STATUS ((uint16_t)0x0001) |
PHY Link mask
Definition at line 214 of file stm32f4xx_hal_conf.h.
| #define PHY_LINKED_STATUS ((uint16_t)0x0004) |
Valid link established
Definition at line 205 of file stm32f4xx_hal_conf.h.
| #define PHY_LOOPBACK ((uint16_t)0x4000) |
Select loop-back mode
Definition at line 194 of file stm32f4xx_hal_conf.h.
| #define PHY_MICR ((uint16_t)0x11) |
MII Interrupt Control Register
Definition at line 211 of file stm32f4xx_hal_conf.h.
| #define PHY_MICR_INT_EN ((uint16_t)0x0002) |
PHY Enable interrupts
Definition at line 218 of file stm32f4xx_hal_conf.h.
| #define PHY_MICR_INT_OE ((uint16_t)0x0001) |
PHY Enable output interrupt events
Definition at line 219 of file stm32f4xx_hal_conf.h.
| #define PHY_MISR ((uint16_t)0x12) |
MII Interrupt Status and Misc. Control Register
Definition at line 212 of file stm32f4xx_hal_conf.h.
| #define PHY_MISR_LINK_INT_EN ((uint16_t)0x0020) |
Enable Interrupt on change of link status
Definition at line 221 of file stm32f4xx_hal_conf.h.
| #define PHY_POWERDOWN ((uint16_t)0x0800) |
Select the power down mode
Definition at line 201 of file stm32f4xx_hal_conf.h.
| #define PHY_READ_TO ((uint32_t)0x0000FFFF) |
Definition at line 185 of file stm32f4xx_hal_conf.h.
| #define PHY_RESET ((uint16_t)0x8000) |
PHY Reset
Definition at line 193 of file stm32f4xx_hal_conf.h.
| #define PHY_RESET_DELAY ((uint32_t)0x000000FF) |
Definition at line 181 of file stm32f4xx_hal_conf.h.
| #define PHY_RESTART_AUTONEGOTIATION ((uint16_t)0x0200) |
Restart auto-negotiation function
Definition at line 200 of file stm32f4xx_hal_conf.h.
| #define PHY_SPEED_STATUS ((uint16_t)0x0002) |
PHY Speed mask
Definition at line 215 of file stm32f4xx_hal_conf.h.
| #define PHY_SR ((uint16_t)0x10) |
PHY status register Offset
Definition at line 210 of file stm32f4xx_hal_conf.h.
| #define PHY_WRITE_TO ((uint32_t)0x0000FFFF) |
Definition at line 186 of file stm32f4xx_hal_conf.h.
| #define PREFETCH_ENABLE 1 |
Definition at line 147 of file stm32f4xx_hal_conf.h.
| #define TICK_INT_PRIORITY ((uint32_t)2) |
tick interrupt priority
Definition at line 145 of file stm32f4xx_hal_conf.h.
| #define USE_RTOS 0 |
Definition at line 146 of file stm32f4xx_hal_conf.h.
| #define VDD_VALUE ((uint32_t)3300) |
This is the HAL system configuration section.
Value of VDD in mv
Definition at line 144 of file stm32f4xx_hal_conf.h.
Generated by
1.8.11