documentation.help

X-CUBE-SPN11 for X-NUCLEO-IHM11M1: stm32f4xx_hal_conf.h Source File

From X-CUBE-SPN11 for X-NUCLEO-IHM11M1

previous page next page
stm32f4xx_hal_conf.h
Go to the documentation of this file.
1 /**
2  ******************************************************************************
3  * @file stm32f4xx_hal_conf.h
4  * @brief HAL configuration file.
5  ******************************************************************************
6  * @attention
7  *
8  * <h2><center>&copy; COPYRIGHT(c) 2015 STMicroelectronics</center></h2>
9  *
10  * Redistribution and use in source and binary forms, with or without modification,
11  * are permitted provided that the following conditions are met:
12  * 1. Redistributions of source code must retain the above copyright notice,
13  * this list of conditions and the following disclaimer.
14  * 2. Redistributions in binary form must reproduce the above copyright notice,
15  * this list of conditions and the following disclaimer in the documentation
16  * and/or other materials provided with the distribution.
17  * 3. Neither the name of STMicroelectronics nor the names of its contributors
18  * may be used to endorse or promote products derived from this software
19  * without specific prior written permission.
20  *
21  * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
22  * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
23  * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
24  * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
25  * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
26  * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
27  * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
28  * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
29  * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
30  * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
31  *
32  ******************************************************************************
33  */
34 
35 /* Define to prevent recursive inclusion -------------------------------------*/
36 #ifndef __STM32F4xx_HAL_CONF_H
37 #define __STM32F4xx_HAL_CONF_H
38 
39 #ifdef __cplusplus
40  extern "C" {
41 #endif
42 
43 /* Exported types ------------------------------------------------------------*/
44 /* Exported constants --------------------------------------------------------*/
45 
46 /* ########################## Module Selection ############################## */
47 /**
48  * @brief This is the list of modules to be used in the HAL driver
49  */
50 #define HAL_MODULE_ENABLED
51 #define HAL_ADC_MODULE_ENABLED
52 //#define HAL_CAN_MODULE_ENABLED
53 //#define HAL_CRC_MODULE_ENABLED
54 //#define HAL_CRYP_MODULE_ENABLED
55 //#define HAL_DAC_MODULE_ENABLED
56 //#define HAL_DCMI_MODULE_ENABLED
57 //#define HAL_DMA2D_MODULE_ENABLED
58 //#define HAL_ETH_MODULE_ENABLED
59 //#define HAL_NAND_MODULE_ENABLED
60 //#define HAL_NOR_MODULE_ENABLED
61 //#define HAL_PCCARD_MODULE_ENABLED
62 //#define HAL_SRAM_MODULE_ENABLED
63 //#define HAL_SDRAM_MODULE_ENABLED
64 //#define HAL_HASH_MODULE_ENABLED
65 //#define HAL_I2C_MODULE_ENABLED
66 //#define HAL_I2S_MODULE_ENABLED
67 //#define HAL_IWDG_MODULE_ENABLED
68 //#define HAL_LTDC_MODULE_ENABLED
69 //#define HAL_RNG_MODULE_ENABLED
70 //#define HAL_RTC_MODULE_ENABLED
71 //#define HAL_SAI_MODULE_ENABLED
72 //#define HAL_SD_MODULE_ENABLED
73 #define HAL_SPI_MODULE_ENABLED
74 #define HAL_TIM_MODULE_ENABLED
75 #define HAL_UART_MODULE_ENABLED
76 //#define HAL_USART_MODULE_ENABLED
77 //#define HAL_IRDA_MODULE_ENABLED
78 //#define HAL_SMARTCARD_MODULE_ENABLED
79 //#define HAL_WWDG_MODULE_ENABLED
80 //#define HAL_PCD_MODULE_ENABLED
81 //#define HAL_HCD_MODULE_ENABLED
82 #define HAL_GPIO_MODULE_ENABLED
83 #define HAL_DMA_MODULE_ENABLED
84 #define HAL_RCC_MODULE_ENABLED
85 #define HAL_FLASH_MODULE_ENABLED
86 #define HAL_PWR_MODULE_ENABLED
87 #define HAL_CORTEX_MODULE_ENABLED
88 
89 /* ########################## HSE/HSI Values adaptation ##################### */
90 /**
91  * @brief Adjust the value of External High Speed oscillator (HSE) used in your application.
92  * This value is used by the RCC HAL module to compute the system frequency
93  * (when HSE is used as system clock source, directly or through the PLL).
94  */
95 #if !defined (HSE_VALUE)
96  #define HSE_VALUE ((uint32_t)8000000) /*!< Value of the External oscillator in Hz */
97 #endif /* HSE_VALUE */
98 
99 #if !defined (HSE_STARTUP_TIMEOUT)
100  #define HSE_STARTUP_TIMEOUT ((uint32_t)5000) /*!< Time out for HSE start up, in ms */
101 #endif /* HSE_STARTUP_TIMEOUT */
102 
103 /**
104  * @brief Internal High Speed oscillator (HSI) value.
105  * This value is used by the RCC HAL module to compute the system frequency
106  * (when HSI is used as system clock source, directly or through the PLL).
107  */
108 #if !defined (HSI_VALUE)
109  #define HSI_VALUE ((uint32_t)16000000) /*!< Value of the Internal oscillator in Hz*/
110 #endif /* HSI_VALUE */
111 
112 /**
113  * @brief Internal Low Speed oscillator (LSI) value.
114  */
115 #if !defined (LSI_VALUE)
116  #define LSI_VALUE ((uint32_t)32000)
117 #endif /* LSI_VALUE */ /*!< Value of the Internal Low Speed oscillator in Hz
118  The real value may vary depending on the variations
119  in voltage and temperature. */
120 /**
121  * @brief External Low Speed oscillator (LSE) value.
122  */
123 #if !defined (LSE_VALUE)
124  #define LSE_VALUE ((uint32_t)32768) /*!< Value of the External Low Speed oscillator in Hz */
125 #endif /* LSE_VALUE */
126 
127 /**
128  * @brief External clock source for I2S peripheral
129  * This value is used by the I2S HAL module to compute the I2S clock source
130  * frequency, this source is inserted directly through I2S_CKIN pad.
131  */
132 #if !defined (EXTERNAL_CLOCK_VALUE)
133  #define EXTERNAL_CLOCK_VALUE ((uint32_t)12288000) /*!< Value of the External audio frequency in Hz*/
134 #endif /* EXTERNAL_CLOCK_VALUE */
135 
136 /* Tip: To avoid modifying this file each time you need to use different HSE,
137  === you can define the HSE value in your toolchain compiler preprocessor. */
138 
139 /* ########################### System Configuration ######################### */
140 /**
141  * @brief This is the HAL system configuration section
142  */
143 
144 #define VDD_VALUE ((uint32_t)3300) /*!< Value of VDD in mv */
145 #define TICK_INT_PRIORITY ((uint32_t)2) /*!< tick interrupt priority */
146 #define USE_RTOS 0
147 #define PREFETCH_ENABLE 1
148 #define INSTRUCTION_CACHE_ENABLE 1
149 #define DATA_CACHE_ENABLE 1
150 
151 /* ########################## Assert Selection ############################## */
152 /**
153  * @brief Uncomment the line below to expanse the "assert_param" macro in the
154  * HAL drivers code
155  */
156 /* #define USE_FULL_ASSERT 1 */
157 
158 /* ################## Ethernet peripheral configuration ##################### */
159 
160 /* Section 1 : Ethernet peripheral configuration */
161 
162 /* MAC ADDRESS: MAC_ADDR0:MAC_ADDR1:MAC_ADDR2:MAC_ADDR3:MAC_ADDR4:MAC_ADDR5 */
163 #define MAC_ADDR0 2
164 #define MAC_ADDR1 0
165 #define MAC_ADDR2 0
166 #define MAC_ADDR3 0
167 #define MAC_ADDR4 0
168 #define MAC_ADDR5 0
169 
170 /* Definition of the Ethernet driver buffers size and count */
171 #define ETH_RX_BUF_SIZE ETH_MAX_PACKET_SIZE /* buffer size for receive */
172 #define ETH_TX_BUF_SIZE ETH_MAX_PACKET_SIZE /* buffer size for transmit */
173 #define ETH_RXBUFNB ((uint32_t)4) /* 4 Rx buffers of size ETH_RX_BUF_SIZE */
174 #define ETH_TXBUFNB ((uint32_t)4) /* 4 Tx buffers of size ETH_TX_BUF_SIZE */
175 
176 /* Section 2: PHY configuration section */
177 
178 /* DP83848 PHY Address*/
179 #define DP83848_PHY_ADDRESS 0x01
180 /* PHY Reset delay these values are based on a 1 ms Systick interrupt*/
181 #define PHY_RESET_DELAY ((uint32_t)0x000000FF)
182 /* PHY Configuration delay */
183 #define PHY_CONFIG_DELAY ((uint32_t)0x00000FFF)
184 
185 #define PHY_READ_TO ((uint32_t)0x0000FFFF)
186 #define PHY_WRITE_TO ((uint32_t)0x0000FFFF)
187 
188 /* Section 3: Common PHY Registers */
189 
190 #define PHY_BCR ((uint16_t)0x00) /*!< Transceiver Basic Control Register */
191 #define PHY_BSR ((uint16_t)0x01) /*!< Transceiver Basic Status Register */
192 
193 #define PHY_RESET ((uint16_t)0x8000) /*!< PHY Reset */
194 #define PHY_LOOPBACK ((uint16_t)0x4000) /*!< Select loop-back mode */
195 #define PHY_FULLDUPLEX_100M ((uint16_t)0x2100) /*!< Set the full-duplex mode at 100 Mb/s */
196 #define PHY_HALFDUPLEX_100M ((uint16_t)0x2000) /*!< Set the half-duplex mode at 100 Mb/s */
197 #define PHY_FULLDUPLEX_10M ((uint16_t)0x0100) /*!< Set the full-duplex mode at 10 Mb/s */
198 #define PHY_HALFDUPLEX_10M ((uint16_t)0x0000) /*!< Set the half-duplex mode at 10 Mb/s */
199 #define PHY_AUTONEGOTIATION ((uint16_t)0x1000) /*!< Enable auto-negotiation function */
200 #define PHY_RESTART_AUTONEGOTIATION ((uint16_t)0x0200) /*!< Restart auto-negotiation function */
201 #define PHY_POWERDOWN ((uint16_t)0x0800) /*!< Select the power down mode */
202 #define PHY_ISOLATE ((uint16_t)0x0400) /*!< Isolate PHY from MII */
203 
204 #define PHY_AUTONEGO_COMPLETE ((uint16_t)0x0020) /*!< Auto-Negotiation process completed */
205 #define PHY_LINKED_STATUS ((uint16_t)0x0004) /*!< Valid link established */
206 #define PHY_JABBER_DETECTION ((uint16_t)0x0002) /*!< Jabber condition detected */
207 
208 /* Section 4: Extended PHY Registers */
209 
210 #define PHY_SR ((uint16_t)0x10) /*!< PHY status register Offset */
211 #define PHY_MICR ((uint16_t)0x11) /*!< MII Interrupt Control Register */
212 #define PHY_MISR ((uint16_t)0x12) /*!< MII Interrupt Status and Misc. Control Register */
213 
214 #define PHY_LINK_STATUS ((uint16_t)0x0001) /*!< PHY Link mask */
215 #define PHY_SPEED_STATUS ((uint16_t)0x0002) /*!< PHY Speed mask */
216 #define PHY_DUPLEX_STATUS ((uint16_t)0x0004) /*!< PHY Duplex mask */
217 
218 #define PHY_MICR_INT_EN ((uint16_t)0x0002) /*!< PHY Enable interrupts */
219 #define PHY_MICR_INT_OE ((uint16_t)0x0001) /*!< PHY Enable output interrupt events */
220 
221 #define PHY_MISR_LINK_INT_EN ((uint16_t)0x0020) /*!< Enable Interrupt on change of link status */
222 #define PHY_LINK_INTERRUPT ((uint16_t)0x2000) /*!< PHY link status interrupt mask */
223 
224 /* Includes ------------------------------------------------------------------*/
225 /**
226  * @brief Include module's header file
227  */
228 
229 #ifdef HAL_RCC_MODULE_ENABLED
230  #include "stm32f4xx_hal_rcc.h"
231 #endif /* HAL_RCC_MODULE_ENABLED */
232 
233 #ifdef HAL_GPIO_MODULE_ENABLED
234  #include "stm32f4xx_hal_gpio.h"
235 #endif /* HAL_GPIO_MODULE_ENABLED */
236 
237 #ifdef HAL_DMA_MODULE_ENABLED
238  #include "stm32f4xx_hal_dma.h"
239 #endif /* HAL_DMA_MODULE_ENABLED */
240 
241 #ifdef HAL_CORTEX_MODULE_ENABLED
242  #include "stm32f4xx_hal_cortex.h"
243 #endif /* HAL_CORTEX_MODULE_ENABLED */
244 
245 #ifdef HAL_ADC_MODULE_ENABLED
246  #include "stm32f4xx_hal_adc.h"
247 #endif /* HAL_ADC_MODULE_ENABLED */
248 
249 #ifdef HAL_CAN_MODULE_ENABLED
250  #include "stm32f4xx_hal_can.h"
251 #endif /* HAL_CAN_MODULE_ENABLED */
252 
253 #ifdef HAL_CRC_MODULE_ENABLED
254  #include "stm32f4xx_hal_crc.h"
255 #endif /* HAL_CRC_MODULE_ENABLED */
256 
257 #ifdef HAL_CRYP_MODULE_ENABLED
258  #include "stm32f4xx_hal_cryp.h"
259 #endif /* HAL_CRYP_MODULE_ENABLED */
260 
261 #ifdef HAL_DMA2D_MODULE_ENABLED
262  #include "stm32f4xx_hal_dma2d.h"
263 #endif /* HAL_DMA2D_MODULE_ENABLED */
264 
265 #ifdef HAL_DAC_MODULE_ENABLED
266  #include "stm32f4xx_hal_dac.h"
267 #endif /* HAL_DAC_MODULE_ENABLED */
268 
269 #ifdef HAL_DCMI_MODULE_ENABLED
270  #include "stm32f4xx_hal_dcmi.h"
271 #endif /* HAL_DCMI_MODULE_ENABLED */
272 
273 #ifdef HAL_ETH_MODULE_ENABLED
274  #include "stm32f4xx_hal_eth.h"
275 #endif /* HAL_ETH_MODULE_ENABLED */
276 
277 #ifdef HAL_FLASH_MODULE_ENABLED
278  #include "stm32f4xx_hal_flash.h"
279 #endif /* HAL_FLASH_MODULE_ENABLED */
280 
281 #ifdef HAL_SRAM_MODULE_ENABLED
282  #include "stm32f4xx_hal_sram.h"
283 #endif /* HAL_SRAM_MODULE_ENABLED */
284 
285 #ifdef HAL_NOR_MODULE_ENABLED
286  #include "stm32f4xx_hal_nor.h"
287 #endif /* HAL_NOR_MODULE_ENABLED */
288 
289 #ifdef HAL_NAND_MODULE_ENABLED
290  #include "stm32f4xx_hal_nand.h"
291 #endif /* HAL_NAND_MODULE_ENABLED */
292 
293 #ifdef HAL_PCCARD_MODULE_ENABLED
294  #include "stm32f4xx_hal_pccard.h"
295 #endif /* HAL_PCCARD_MODULE_ENABLED */
296 
297 #ifdef HAL_SDRAM_MODULE_ENABLED
298  #include "stm32f4xx_hal_sdram.h"
299 #endif /* HAL_SDRAM_MODULE_ENABLED */
300 
301 #ifdef HAL_HASH_MODULE_ENABLED
302  #include "stm32f4xx_hal_hash.h"
303 #endif /* HAL_HASH_MODULE_ENABLED */
304 
305 #ifdef HAL_I2C_MODULE_ENABLED
306  #include "stm32f4xx_hal_i2c.h"
307 #endif /* HAL_I2C_MODULE_ENABLED */
308 
309 #ifdef HAL_I2S_MODULE_ENABLED
310  #include "stm32f4xx_hal_i2s.h"
311 #endif /* HAL_I2S_MODULE_ENABLED */
312 
313 #ifdef HAL_IWDG_MODULE_ENABLED
314  #include "stm32f4xx_hal_iwdg.h"
315 #endif /* HAL_IWDG_MODULE_ENABLED */
316 
317 #ifdef HAL_LTDC_MODULE_ENABLED
318  #include "stm32f4xx_hal_ltdc.h"
319 #endif /* HAL_LTDC_MODULE_ENABLED */
320 
321 #ifdef HAL_PWR_MODULE_ENABLED
322  #include "stm32f4xx_hal_pwr.h"
323 #endif /* HAL_PWR_MODULE_ENABLED */
324 
325 #ifdef HAL_RNG_MODULE_ENABLED
326  #include "stm32f4xx_hal_rng.h"
327 #endif /* HAL_RNG_MODULE_ENABLED */
328 
329 #ifdef HAL_RTC_MODULE_ENABLED
330  #include "stm32f4xx_hal_rtc.h"
331 #endif /* HAL_RTC_MODULE_ENABLED */
332 
333 #ifdef HAL_SAI_MODULE_ENABLED
334  #include "stm32f4xx_hal_sai.h"
335 #endif /* HAL_SAI_MODULE_ENABLED */
336 
337 #ifdef HAL_SD_MODULE_ENABLED
338  #include "stm32f4xx_hal_sd.h"
339 #endif /* HAL_SD_MODULE_ENABLED */
340 
341 #ifdef HAL_SPI_MODULE_ENABLED
342  #include "stm32f4xx_hal_spi.h"
343 #endif /* HAL_SPI_MODULE_ENABLED */
344 
345 #ifdef HAL_TIM_MODULE_ENABLED
346  #include "stm32f4xx_hal_tim.h"
347 #endif /* HAL_TIM_MODULE_ENABLED */
348 
349 #ifdef HAL_UART_MODULE_ENABLED
350  #include "stm32f4xx_hal_uart.h"
351 #endif /* HAL_UART_MODULE_ENABLED */
352 
353 #ifdef HAL_USART_MODULE_ENABLED
354  #include "stm32f4xx_hal_usart.h"
355 #endif /* HAL_USART_MODULE_ENABLED */
356 
357 #ifdef HAL_IRDA_MODULE_ENABLED
358  #include "stm32f4xx_hal_irda.h"
359 #endif /* HAL_IRDA_MODULE_ENABLED */
360 
361 #ifdef HAL_SMARTCARD_MODULE_ENABLED
362  #include "stm32f4xx_hal_smartcard.h"
363 #endif /* HAL_SMARTCARD_MODULE_ENABLED */
364 
365 #ifdef HAL_WWDG_MODULE_ENABLED
366  #include "stm32f4xx_hal_wwdg.h"
367 #endif /* HAL_WWDG_MODULE_ENABLED */
368 
369 #ifdef HAL_PCD_MODULE_ENABLED
370  #include "stm32f4xx_hal_pcd.h"
371 #endif /* HAL_PCD_MODULE_ENABLED */
372 
373 #ifdef HAL_HCD_MODULE_ENABLED
374  #include "stm32f4xx_hal_hcd.h"
375 #endif /* HAL_HCD_MODULE_ENABLED */
376 
377 /* Exported macro ------------------------------------------------------------*/
378 #ifdef USE_FULL_ASSERT
379 /**
380  * @brief The assert_param macro is used for function's parameters check.
381  * @param expr: If expr is false, it calls assert_failed function
382  * which reports the name of the source file and the source
383  * line number of the call that failed.
384  * If expr is true, it returns no value.
385  * @retval None
386  */
387  #define assert_param(expr) ((expr) ? (void)0 : assert_failed((uint8_t *)__FILE__, __LINE__))
388 /* Exported functions ------------------------------------------------------- */
389  void assert_failed(uint8_t* file, uint32_t line);
390 #else
391  #define assert_param(expr) ((void)0)
392 #endif /* USE_FULL_ASSERT */
393 
394 #ifdef __cplusplus
395 }
396 #endif
397 
398 #endif /* __STM32F4xx_HAL_CONF_H */
399 
400 
401 /************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
Generated by   doxygen 1.8.11
previous page start next page