Functions
static void	TI1_Config (uint8_t TIM2_ICPolarity, uint8_t TIM2_ICSelection, uint8_t TIM2_ICFilter)
	Configure the TI1 as Input.
static void	TI2_Config (uint8_t TIM2_ICPolarity, uint8_t TIM2_ICSelection, uint8_t TIM2_ICFilter)
	Configure the TI2 as Input.
static void	TI3_Config (uint8_t TIM2_ICPolarity, uint8_t TIM2_ICSelection, uint8_t TIM2_ICFilter)
	Configure the TI3 as Input.
void	TIM2_ARRPreloadConfig (FunctionalState NewState)
	Enables or disables TIM2 peripheral Preload register on ARR.
void	TIM2_CCxCmd (TIM2_Channel_TypeDef TIM2_Channel, FunctionalState NewState)
	Enables or disables the TIM2 Capture Compare Channel x.
void	TIM2_ClearFlag (TIM2_FLAG_TypeDef TIM2_FLAG)
	Clears the TIM2�s pending flags.
void	TIM2_ClearITPendingBit (TIM2_IT_TypeDef TIM2_IT)
	Clears the TIM2's interrupt pending bits.
void	TIM2_Cmd (FunctionalState NewState)
	Enables or disables the TIM2 peripheral.
void	TIM2_DeInit (void)
	Deinitializes the TIM2 peripheral registers to their default reset values.
void	TIM2_ForcedOC1Config (TIM2_ForcedAction_TypeDef TIM2_ForcedAction)
	Forces the TIM2 Channel1 output waveform to active or inactive level.
void	TIM2_ForcedOC2Config (TIM2_ForcedAction_TypeDef TIM2_ForcedAction)
	Forces the TIM2 Channel2 output waveform to active or inactive level.
void	TIM2_ForcedOC3Config (TIM2_ForcedAction_TypeDef TIM2_ForcedAction)
	Forces the TIM2 Channel3 output waveform to active or inactive level.
void	TIM2_GenerateEvent (TIM2_EventSource_TypeDef TIM2_EventSource)
	Configures the TIM2 event to be generated by software.
uint16_t	TIM2_GetCapture1 (void)
	Gets the TIM2 Input Capture 1 value.
uint16_t	TIM2_GetCapture2 (void)
	Gets the TIM2 Input Capture 2 value.
uint16_t	TIM2_GetCapture3 (void)
	Gets the TIM2 Input Capture 3 value.
uint16_t	TIM2_GetCounter (void)
	Gets the TIM2 Counter value.
FlagStatus	TIM2_GetFlagStatus (TIM2_FLAG_TypeDef TIM2_FLAG)
	Checks whether the specified TIM2 flag is set or not.
ITStatus	TIM2_GetITStatus (TIM2_IT_TypeDef TIM2_IT)
	Checks whether the TIM2 interrupt has occurred or not.
TIM2_Prescaler_TypeDef	TIM2_GetPrescaler (void)
	Gets the TIM2 Prescaler value.
void	TIM2_ICInit (TIM2_Channel_TypeDef TIM2_Channel, TIM2_ICPolarity_TypeDef TIM2_ICPolarity, TIM2_ICSelection_TypeDef TIM2_ICSelection, TIM2_ICPSC_TypeDef TIM2_ICPrescaler, uint8_t TIM2_ICFilter)
	Initializes the TIM2 peripheral according to the specified parameters.
void	TIM2_ITConfig (TIM2_IT_TypeDef TIM2_IT, FunctionalState NewState)
	Enables or disables the specified TIM2 interrupts.
void	TIM2_OC1Init (TIM2_OCMode_TypeDef TIM2_OCMode, TIM2_OutputState_TypeDef TIM2_OutputState, uint16_t TIM2_Pulse, TIM2_OCPolarity_TypeDef TIM2_OCPolarity)
	Initializes the TIM2 Channel1 according to the specified parameters.
void	TIM2_OC1PolarityConfig (TIM2_OCPolarity_TypeDef TIM2_OCPolarity)
	Configures the TIM2 Channel 1 polarity.
void	TIM2_OC1PreloadConfig (FunctionalState NewState)
	Enables or disables the TIM2 peripheral Preload Register on CCR1.
void	TIM2_OC2Init (TIM2_OCMode_TypeDef TIM2_OCMode, TIM2_OutputState_TypeDef TIM2_OutputState, uint16_t TIM2_Pulse, TIM2_OCPolarity_TypeDef TIM2_OCPolarity)
	Initializes the TIM2 Channel2 according to the specified parameters.
void	TIM2_OC2PolarityConfig (TIM2_OCPolarity_TypeDef TIM2_OCPolarity)
	Configures the TIM2 Channel 2 polarity.
void	TIM2_OC2PreloadConfig (FunctionalState NewState)
	Enables or disables the TIM2 peripheral Preload Register on CCR2.
void	TIM2_OC3Init (TIM2_OCMode_TypeDef TIM2_OCMode, TIM2_OutputState_TypeDef TIM2_OutputState, uint16_t TIM2_Pulse, TIM2_OCPolarity_TypeDef TIM2_OCPolarity)
	Initializes the TIM2 Channel3 according to the specified parameters.
void	TIM2_OC3PolarityConfig (TIM2_OCPolarity_TypeDef TIM2_OCPolarity)
	Configures the TIM2 Channel 3 polarity.
void	TIM2_OC3PreloadConfig (FunctionalState NewState)
	Enables or disables the TIM2 peripheral Preload Register on CCR3.
void	TIM2_PrescalerConfig (TIM2_Prescaler_TypeDef Prescaler, TIM2_PSCReloadMode_TypeDef TIM2_PSCReloadMode)
	Configures the TIM2 Prescaler.
void	TIM2_PWMIConfig (TIM2_Channel_TypeDef TIM2_Channel, TIM2_ICPolarity_TypeDef TIM2_ICPolarity, TIM2_ICSelection_TypeDef TIM2_ICSelection, TIM2_ICPSC_TypeDef TIM2_ICPrescaler, uint8_t TIM2_ICFilter)
	Configures the TIM2 peripheral in PWM Input Mode according to the specified parameters.
void	TIM2_SelectOCxM (TIM2_Channel_TypeDef TIM2_Channel, TIM2_OCMode_TypeDef TIM2_OCMode)
	Selects the TIM2 Output Compare Mode.
void	TIM2_SelectOnePulseMode (TIM2_OPMode_TypeDef TIM2_OPMode)
	Selects the TIM2�s One Pulse Mode.
void	TIM2_SetAutoreload (uint16_t Autoreload)
	Sets the TIM2 Autoreload Register value.
void	TIM2_SetCompare1 (uint16_t Compare1)
	Sets the TIM2 Capture Compare1 Register value.
void	TIM2_SetCompare2 (uint16_t Compare2)
	Sets the TIM2 Capture Compare2 Register value.
void	TIM2_SetCompare3 (uint16_t Compare3)
	Sets the TIM2 Capture Compare3 Register value.
void	TIM2_SetCounter (uint16_t Counter)
	Sets the TIM2 Counter Register value.
void	TIM2_SetIC1Prescaler (TIM2_ICPSC_TypeDef TIM2_IC1Prescaler)
	Sets the TIM2 Input Capture 1 Prescaler.
void	TIM2_SetIC2Prescaler (TIM2_ICPSC_TypeDef TIM2_IC2Prescaler)
	Sets the TIM2 Input Capture 2 prescaler.
void	TIM2_SetIC3Prescaler (TIM2_ICPSC_TypeDef TIM2_IC3Prescaler)
	Sets the TIM2 Input Capture 3 prescaler.
void	TIM2_TimeBaseInit (TIM2_Prescaler_TypeDef TIM2_Prescaler, uint16_t TIM2_Period)
	Initializes the TIM2 Time Base Unit according to the specified parameters.
void	TIM2_UpdateDisableConfig (FunctionalState NewState)
	Enables or Disables the TIM2 Update event.
void	TIM2_UpdateRequestConfig (TIM2_UpdateSource_TypeDef TIM2_UpdateSource)
	Selects the TIM2 Update Request Interrupt source.

Function Documentation

static void TI1_Config	(	uint8_t	TIM2_ICPolarity,
		uint8_t	TIM2_ICSelection,
		uint8_t	TIM2_ICFilter
	)		`[static]`

Configure the TI1 as Input.

Parameters:

TIM2_ICPolarity	The Input Polarity. This parameter can be one of the following values: TIM2_ICPOLARITY_FALLING TIM2_ICPOLARITY_RISING
TIM2_ICSelection	specifies the input to be used. This parameter can be one of the following values: TIM2_ICSELECTION_DIRECTTI: TIM2 Input 1 is selected to be connected to IC1. TIM2_ICSELECTION_INDIRECTTI: TIM2 Input 1 is selected to be connected to IC2.
TIM2_ICFilter	Specifies the Input Capture Filter. This parameter must be a value between 0x00 and 0x0F.

Return values:

None

Definition at line 1181 of file stm8s_tim2.c.

References TIM2_CCER1_CC1E, TIM2_CCER1_CC1P, TIM2_CCMR_CCxS, TIM2_CCMR_ICxF, and TIM2_ICPOLARITY_RISING.

Referenced by TIM2_ICInit(), and TIM2_PWMIConfig().

static void TI2_Config	(	uint8_t	TIM2_ICPolarity,
		uint8_t	TIM2_ICSelection,
		uint8_t	TIM2_ICFilter
	)		`[static]`

Configure the TI2 as Input.

Parameters:

TIM2_ICPolarity	The Input Polarity. This parameter can be one of the following values: TIM2_ICPOLARITY_FALLING TIM2_ICPOLARITY_RISING
TIM2_ICSelection	specifies the input to be used. This parameter can be one of the following values: TIM2_ICSELECTION_DIRECTTI: TIM2 Input 2 is selected to be connected to IC2. TIM2_ICSELECTION_INDIRECTTI: TIM2 Input 2 is selected to be connected to IC1.
TIM2_ICFilter	Specifies the Input Capture Filter. This parameter must be a value between 0x00 and 0x0F.

Return values:

None

Definition at line 1221 of file stm8s_tim2.c.

References TIM2_CCER1_CC2E, TIM2_CCER1_CC2P, TIM2_CCMR_CCxS, TIM2_CCMR_ICxF, and TIM2_ICPOLARITY_RISING.

Referenced by TIM2_ICInit(), and TIM2_PWMIConfig().

static void TI3_Config	(	uint8_t	TIM2_ICPolarity,
		uint8_t	TIM2_ICSelection,
		uint8_t	TIM2_ICFilter
	)		`[static]`

Configure the TI3 as Input.

Parameters:

TIM2_ICPolarity	The Input Polarity. This parameter can be one of the following values: TIM2_ICPOLARITY_FALLING TIM2_ICPOLARITY_RISING
TIM2_ICSelection	specifies the input to be used. This parameter can be one of the following values: TIM2_ICSELECTION_DIRECTTI: TIM2 Input 3 is selected to be connected to IC3.
TIM2_ICFilter	Specifies the Input Capture Filter. This parameter must be a value between 0x00 and 0x0F.

Return values:

None

Definition at line 1261 of file stm8s_tim2.c.

References TIM2_CCER2_CC3E, TIM2_CCER2_CC3P, TIM2_CCMR_CCxS, TIM2_CCMR_ICxF, and TIM2_ICPOLARITY_RISING.

Referenced by TIM2_ICInit().

void TIM2_ARRPreloadConfig ( FunctionalState NewState )

Enables or disables TIM2 peripheral Preload register on ARR.

Parameters:

NewState new state of the TIM2 peripheral Preload register. This parameter can be ENABLE or DISABLE.

Return values:

None

Definition at line 561 of file stm8s_tim2.c.

References assert_param, DISABLE, IS_FUNCTIONALSTATE_OK, and TIM2_CR1_ARPE.

Referenced by TIM2_Config().

void TIM2_CCxCmd	(	TIM2_Channel_TypeDef	TIM2_Channel,
		FunctionalState	NewState
	)

Enables or disables the TIM2 Capture Compare Channel x.

Parameters:

TIM2_Channel	specifies the TIM2 Channel. This parameter can be one of the following values: TIM2_CHANNEL_1: TIM2 Channel1 TIM2_CHANNEL_2: TIM2 Channel2 TIM2_CHANNEL_3: TIM2 Channel3
NewState	specifies the TIM2 Channel CCxE bit new state. This parameter can be: ENABLE or DISABLE.

Return values:

None

Definition at line 745 of file stm8s_tim2.c.

References assert_param, DISABLE, IS_FUNCTIONALSTATE_OK, IS_TIM2_CHANNEL_OK, TIM2_CCER1_CC1E, TIM2_CCER1_CC2E, TIM2_CCER2_CC3E, TIM2_CHANNEL_1, and TIM2_CHANNEL_2.

void TIM2_ClearFlag ( TIM2_FLAG_TypeDef TIM2_FLAG )

Clears the TIM2�s pending flags.

Parameters:

TIM2_FLAG

specifies the flag to clear. This parameter can be one of the following values:

TIM2_FLAG_UPDATE: TIM2 update Flag
TIM2_FLAG_CC1: TIM2 Capture Compare 1 Flag
TIM2_FLAG_CC2: TIM2 Capture Compare 2 Flag
TIM2_FLAG_CC3: TIM2 Capture Compare 3 Flag
TIM2_FLAG_CC1OF: TIM2 Capture Compare 1 over capture Flag
TIM2_FLAG_CC2OF: TIM2 Capture Compare 2 over capture Flag
TIM2_FLAG_CC3OF: TIM2 Capture Compare 3 over capture Flag

Return values:

None.

Definition at line 1103 of file stm8s_tim2.c.

References assert_param, and IS_TIM2_CLEAR_FLAG_OK.

void TIM2_ClearITPendingBit ( TIM2_IT_TypeDef TIM2_IT )

Clears the TIM2's interrupt pending bits.

Parameters:

TIM2_IT

specifies the pending bit to clear. This parameter can be one of the following values:

TIM2_IT_UPDATE: TIM2 update Interrupt source
TIM2_IT_CC1: TIM2 Capture Compare 1 Interrupt source
TIM2_IT_CC2: TIM2 Capture Compare 2 Interrupt source
TIM2_IT_CC3: TIM2 Capture Compare 3 Interrupt source

Return values:

None.

Definition at line 1156 of file stm8s_tim2.c.

References assert_param, and IS_TIM2_IT_OK.

Referenced by INTERRUPT_HANDLER().

void TIM2_Cmd ( FunctionalState NewState )

Enables or disables the TIM2 peripheral.

Parameters:

NewState new state of the TIM2 peripheral. This parameter can be ENABLE or DISABLE.

Return values:

None

Definition at line 339 of file stm8s_tim2.c.

References assert_param, DISABLE, IS_FUNCTIONALSTATE_OK, and TIM2_CR1_CEN.

Referenced by TIM2_Config().

void TIM2_DeInit ( void )

Deinitializes the TIM2 peripheral registers to their default reset values.

Parameters:

None

Return values:

None

Definition at line 52 of file stm8s_tim2.c.

References TIM2_ARRH_RESET_VALUE, TIM2_ARRL_RESET_VALUE, TIM2_CCER1_RESET_VALUE, TIM2_CCER2_RESET_VALUE, TIM2_CCMR1_RESET_VALUE, TIM2_CCMR2_RESET_VALUE, TIM2_CCMR3_RESET_VALUE, TIM2_CCR1H_RESET_VALUE, TIM2_CCR1L_RESET_VALUE, TIM2_CCR2H_RESET_VALUE, TIM2_CCR2L_RESET_VALUE, TIM2_CCR3H_RESET_VALUE, TIM2_CCR3L_RESET_VALUE, TIM2_CNTRH_RESET_VALUE, TIM2_CNTRL_RESET_VALUE, TIM2_CR1_RESET_VALUE, TIM2_IER_RESET_VALUE, TIM2_PSCR_RESET_VALUE, TIM2_SR1_RESET_VALUE, and TIM2_SR2_RESET_VALUE.

void TIM2_ForcedOC1Config ( TIM2_ForcedAction_TypeDef TIM2_ForcedAction )

Forces the TIM2 Channel1 output waveform to active or inactive level.

Parameters:

TIM2_ForcedAction

specifies the forced Action to be set to the output waveform. This parameter can be one of the following values:

TIM2_FORCEDACTION_ACTIVE: Force active level on OC1REF
TIM2_FORCEDACTION_INACTIVE: Force inactive level on OC1REF.

Return values:

None

Definition at line 507 of file stm8s_tim2.c.

References assert_param, IS_TIM2_FORCED_ACTION_OK, and TIM2_CCMR_OCM.

void TIM2_ForcedOC2Config ( TIM2_ForcedAction_TypeDef TIM2_ForcedAction )

Forces the TIM2 Channel2 output waveform to active or inactive level.

Parameters:

TIM2_ForcedAction

specifies the forced Action to be set to the output waveform. This parameter can be one of the following values:

TIM2_FORCEDACTION_ACTIVE: Force active level on OC2REF
TIM2_FORCEDACTION_INACTIVE: Force inactive level on OC2REF.

Return values:

None

Definition at line 526 of file stm8s_tim2.c.

References assert_param, IS_TIM2_FORCED_ACTION_OK, and TIM2_CCMR_OCM.

void TIM2_ForcedOC3Config ( TIM2_ForcedAction_TypeDef TIM2_ForcedAction )

Forces the TIM2 Channel3 output waveform to active or inactive level.

Parameters:

TIM2_ForcedAction

specifies the forced Action to be set to the output waveform. This parameter can be one of the following values:

TIM2_FORCEDACTION_ACTIVE: Force active level on OC3REF
TIM2_FORCEDACTION_INACTIVE: Force inactive level on OC3REF.

Return values:

None

Definition at line 545 of file stm8s_tim2.c.

References assert_param, IS_TIM2_FORCED_ACTION_OK, and TIM2_CCMR_OCM.

void TIM2_GenerateEvent ( TIM2_EventSource_TypeDef TIM2_EventSource )

Configures the TIM2 event to be generated by software.

Parameters:

TIM2_EventSource

specifies the event source. This parameter can be one of the following values:

TIM2_EVENTSOURCE_UPDATE: TIM2 update Event source
TIM2_EVENTSOURCE_CC1: TIM2 Capture Compare 1 Event source
TIM2_EVENTSOURCE_CC2: TIM2 Capture Compare 2 Event source
TIM2_EVENTSOURCE_CC3: TIM2 Capture Compare 3 Event source

Return values:

None

Definition at line 653 of file stm8s_tim2.c.

References assert_param, and IS_TIM2_EVENT_SOURCE_OK.

uint16_t TIM2_GetCapture1 ( void )

Gets the TIM2 Input Capture 1 value.

Parameters:

None

Return values:

Capture Compare 1 Register value.

Definition at line 975 of file stm8s_tim2.c.

uint16_t TIM2_GetCapture2 ( void )

Gets the TIM2 Input Capture 2 value.

Parameters:

None

Return values:

Capture Compare 2 Register value.

Definition at line 995 of file stm8s_tim2.c.

uint16_t TIM2_GetCapture3 ( void )

Gets the TIM2 Input Capture 3 value.

Parameters:

None

Return values:

Capture Compare 3 Register value.

Definition at line 1015 of file stm8s_tim2.c.

uint16_t TIM2_GetCounter ( void )

Gets the TIM2 Counter value.

Parameters:

None

Return values:

Counter Register value.

Definition at line 1035 of file stm8s_tim2.c.

FlagStatus TIM2_GetFlagStatus ( TIM2_FLAG_TypeDef TIM2_FLAG )

Checks whether the specified TIM2 flag is set or not.

Parameters:

TIM2_FLAG

specifies the flag to check. This parameter can be one of the following values:

TIM2_FLAG_UPDATE: TIM2 update Flag
TIM2_FLAG_CC1: TIM2 Capture Compare 1 Flag
TIM2_FLAG_CC2: TIM2 Capture Compare 2 Flag
TIM2_FLAG_CC3: TIM2 Capture Compare 3 Flag
TIM2_FLAG_CC1OF: TIM2 Capture Compare 1 over capture Flag
TIM2_FLAG_CC2OF: TIM2 Capture Compare 2 over capture Flag
TIM2_FLAG_CC3OF: TIM2 Capture Compare 3 over capture Flag

Return values:

FlagStatus The new state of TIM2_FLAG (SET or RESET).

Definition at line 1068 of file stm8s_tim2.c.

References assert_param, IS_TIM2_GET_FLAG_OK, RESET, and SET.

ITStatus TIM2_GetITStatus ( TIM2_IT_TypeDef TIM2_IT )

Checks whether the TIM2 interrupt has occurred or not.

Parameters:

TIM2_IT

specifies the TIM2 interrupt source to check. This parameter can be one of the following values:

TIM2_IT_UPDATE: TIM2 update Interrupt source
TIM2_IT_CC1: TIM2 Capture Compare 1 Interrupt source
TIM2_IT_CC2: TIM2 Capture Compare 2 Interrupt source
TIM2_IT_CC3: TIM2 Capture Compare 3 Interrupt source

Return values:

ITStatus The new state of the TIM2_IT(SET or RESET).

Definition at line 1123 of file stm8s_tim2.c.

References assert_param, IS_TIM2_GET_IT_OK, RESET, and SET.

Referenced by INTERRUPT_HANDLER().

TIM2_Prescaler_TypeDef TIM2_GetPrescaler ( void )

Gets the TIM2 Prescaler value.

Parameters:

None

Return values:

Prescaler Register configuration value TIM2_Prescaler_TypeDef.

Definition at line 1049 of file stm8s_tim2.c.

void TIM2_ICInit	(	TIM2_Channel_TypeDef	TIM2_Channel,
		TIM2_ICPolarity_TypeDef	TIM2_ICPolarity,
		TIM2_ICSelection_TypeDef	TIM2_ICSelection,
		TIM2_ICPSC_TypeDef	TIM2_ICPrescaler,
		uint8_t	TIM2_ICFilter
	)

Initializes the TIM2 peripheral according to the specified parameters.

Parameters:

TIM2_Channel	specifies the Input Capture Channel from TIM2_Channel_TypeDef.
TIM2_ICPolarity	specifies the Input Capture Polarity from TIM2_ICPolarity_TypeDef.
TIM2_ICSelection	specifies the Input Capture Selection from TIM2_ICSelection_TypeDef.
TIM2_ICPrescaler	specifies the Input Capture Prescaler from TIM2_ICPSC_TypeDef.
TIM2_ICFilter	specifies the Input Capture Filter value (value can be an integer from 0x00 to 0x0F).

Return values:

None

Definition at line 212 of file stm8s_tim2.c.

References assert_param, IS_TIM2_CHANNEL_OK, IS_TIM2_IC_FILTER_OK, IS_TIM2_IC_POLARITY_OK, IS_TIM2_IC_PRESCALER_OK, IS_TIM2_IC_SELECTION_OK, TI1_Config(), TI2_Config(), TI3_Config(), TIM2_CHANNEL_1, TIM2_CHANNEL_2, TIM2_SetIC1Prescaler(), TIM2_SetIC2Prescaler(), and TIM2_SetIC3Prescaler().

void TIM2_ITConfig	(	TIM2_IT_TypeDef	TIM2_IT,
		FunctionalState	NewState
	)

Enables or disables the specified TIM2 interrupts.

Parameters:

NewState	new state of the TIM2 peripheral. This parameter can be: ENABLE or DISABLE.
TIM2_IT	specifies the TIM2 interrupts sources to be enabled or disabled. This parameter can be any combination of the following values: TIM2_IT_UPDATE: TIM2 update Interrupt source TIM2_IT_CC1: TIM2 Capture Compare 1 Interrupt source TIM2_IT_CC2: TIM2 Capture Compare 2 Interrupt source TIM2_IT_CC3: TIM2 Capture Compare 3 Interrupt source
NewState	new state of the TIM2 peripheral.

Return values:

None

Definition at line 368 of file stm8s_tim2.c.

References assert_param, DISABLE, IS_FUNCTIONALSTATE_OK, and IS_TIM2_IT_OK.

Referenced by TIM2_Config().

void TIM2_OC1Init	(	TIM2_OCMode_TypeDef	TIM2_OCMode,
		TIM2_OutputState_TypeDef	TIM2_OutputState,
		uint16_t	TIM2_Pulse,
		TIM2_OCPolarity_TypeDef	TIM2_OCPolarity
	)

Initializes the TIM2 Channel1 according to the specified parameters.

Parameters:

TIM2_OCMode	specifies the Output Compare mode from TIM2_OCMode_TypeDef.
TIM2_OutputState	specifies the Output State from TIM2_OutputState_TypeDef.
TIM2_Pulse	specifies the Pulse width value.
TIM2_OCPolarity	specifies the Output Compare Polarity from TIM2_OCPolarity_TypeDef.

Return values:

None

Definition at line 108 of file stm8s_tim2.c.

References assert_param, IS_TIM2_OC_MODE_OK, IS_TIM2_OC_POLARITY_OK, IS_TIM2_OUTPUT_STATE_OK, TIM2_CCER1_CC1E, TIM2_CCER1_CC1P, and TIM2_CCMR_OCM.

Referenced by TIM2_Config().

void TIM2_OC1PolarityConfig ( TIM2_OCPolarity_TypeDef TIM2_OCPolarity )

Configures the TIM2 Channel 1 polarity.

Parameters:

TIM2_OCPolarity

specifies the OC1 Polarity. This parameter can be one of the following values:

TIM2_OCPOLARITY_LOW: Output Compare active low
TIM2_OCPOLARITY_HIGH: Output Compare active high

Return values:

None

Definition at line 670 of file stm8s_tim2.c.

References assert_param, IS_TIM2_OC_POLARITY_OK, TIM2_CCER1_CC1P, and TIM2_OCPOLARITY_HIGH.

void TIM2_OC1PreloadConfig ( FunctionalState NewState )

Enables or disables the TIM2 peripheral Preload Register on CCR1.

Parameters:

NewState new state of the Capture Compare Preload register. This parameter can be ENABLE or DISABLE.

Return values:

None

Definition at line 583 of file stm8s_tim2.c.

References assert_param, DISABLE, IS_FUNCTIONALSTATE_OK, and TIM2_CCMR_OCxPE.

Referenced by TIM2_Config().

void TIM2_OC2Init	(	TIM2_OCMode_TypeDef	TIM2_OCMode,
		TIM2_OutputState_TypeDef	TIM2_OutputState,
		uint16_t	TIM2_Pulse,
		TIM2_OCPolarity_TypeDef	TIM2_OCPolarity
	)

Initializes the TIM2 Channel2 according to the specified parameters.

Parameters:

TIM2_OCMode	specifies the Output Compare mode from TIM2_OCMode_TypeDef.
TIM2_OutputState	specifies the Output State from TIM2_OutputState_TypeDef.
TIM2_Pulse	specifies the Pulse width value.
TIM2_OCPolarity	specifies the Output Compare Polarity from TIM2_OCPolarity_TypeDef.

Return values:

None

Definition at line 142 of file stm8s_tim2.c.

References assert_param, IS_TIM2_OC_MODE_OK, IS_TIM2_OC_POLARITY_OK, IS_TIM2_OUTPUT_STATE_OK, TIM2_CCER1_CC2E, TIM2_CCER1_CC2P, and TIM2_CCMR_OCM.

Referenced by TIM2_Config().

void TIM2_OC2PolarityConfig ( TIM2_OCPolarity_TypeDef TIM2_OCPolarity )

Configures the TIM2 Channel 2 polarity.

Parameters:

TIM2_OCPolarity

specifies the OC2 Polarity. This parameter can be one of the following values:

TIM2_OCPOLARITY_LOW: Output Compare active low
TIM2_OCPOLARITY_HIGH: Output Compare active high

Return values:

None

Definition at line 694 of file stm8s_tim2.c.

References assert_param, IS_TIM2_OC_POLARITY_OK, TIM2_CCER1_CC2P, and TIM2_OCPOLARITY_HIGH.

void TIM2_OC2PreloadConfig ( FunctionalState NewState )

Enables or disables the TIM2 peripheral Preload Register on CCR2.

Parameters:

NewState new state of the Capture Compare Preload register. This parameter can be ENABLE or DISABLE.

Return values:

None

Definition at line 605 of file stm8s_tim2.c.

References assert_param, DISABLE, IS_FUNCTIONALSTATE_OK, and TIM2_CCMR_OCxPE.

Referenced by TIM2_Config().

void TIM2_OC3Init	(	TIM2_OCMode_TypeDef	TIM2_OCMode,
		TIM2_OutputState_TypeDef	TIM2_OutputState,
		uint16_t	TIM2_Pulse,
		TIM2_OCPolarity_TypeDef	TIM2_OCPolarity
	)

Initializes the TIM2 Channel3 according to the specified parameters.

Parameters:

TIM2_OCMode	specifies the Output Compare mode from TIM2_OCMode_TypeDef.
TIM2_OutputState	specifies the Output State from TIM2_OutputState_TypeDef.
TIM2_Pulse	specifies the Pulse width value.
TIM2_OCPolarity	specifies the Output Compare Polarity from TIM2_OCPolarity_TypeDef.

Return values:

None

Definition at line 179 of file stm8s_tim2.c.

References assert_param, IS_TIM2_OC_MODE_OK, IS_TIM2_OC_POLARITY_OK, IS_TIM2_OUTPUT_STATE_OK, TIM2_CCER2_CC3E, TIM2_CCER2_CC3P, and TIM2_CCMR_OCM.

Referenced by TIM2_Config().

void TIM2_OC3PolarityConfig ( TIM2_OCPolarity_TypeDef TIM2_OCPolarity )

Configures the TIM2 Channel 3 polarity.

Parameters:

TIM2_OCPolarity

specifies the OC3 Polarity. This parameter can be one of the following values:

TIM2_OCPOLARITY_LOW: Output Compare active low
TIM2_OCPOLARITY_HIGH: Output Compare active high

Return values:

None

Definition at line 718 of file stm8s_tim2.c.

References assert_param, IS_TIM2_OC_POLARITY_OK, TIM2_CCER2_CC3P, and TIM2_OCPOLARITY_HIGH.

void TIM2_OC3PreloadConfig ( FunctionalState NewState )

Enables or disables the TIM2 peripheral Preload Register on CCR3.

Parameters:

NewState new state of the Capture Compare Preload register. This parameter can be ENABLE or DISABLE.

Return values:

None

Definition at line 627 of file stm8s_tim2.c.

References assert_param, DISABLE, IS_FUNCTIONALSTATE_OK, and TIM2_CCMR_OCxPE.

Referenced by TIM2_Config().

void TIM2_PrescalerConfig	(	TIM2_Prescaler_TypeDef	Prescaler,
		TIM2_PSCReloadMode_TypeDef	TIM2_PSCReloadMode
	)

Configures the TIM2 Prescaler.

Parameters:

Prescaler

specifies the Prescaler Register value This parameter can be one of the following values

TIM2_PRESCALER_1
TIM2_PRESCALER_2
TIM2_PRESCALER_4
TIM2_PRESCALER_8
TIM2_PRESCALER_16
TIM2_PRESCALER_32
TIM2_PRESCALER_64
TIM2_PRESCALER_128
TIM2_PRESCALER_256
TIM2_PRESCALER_512
TIM2_PRESCALER_1024
TIM2_PRESCALER_2048
TIM2_PRESCALER_4096
TIM2_PRESCALER_8192
TIM2_PRESCALER_16384
TIM2_PRESCALER_32768

TIM2_PSCReloadMode

specifies the TIM2 Prescaler Reload mode. This parameter can be one of the following values

TIM2_PSCRELOADMODE_IMMEDIATE: The Prescaler is loaded immediately.
TIM2_PSCRELOADMODE_UPDATE: The Prescaler is loaded at the update event.

Return values:

None

Definition at line 484 of file stm8s_tim2.c.

References assert_param, IS_TIM2_PRESCALER_OK, and IS_TIM2_PRESCALER_RELOAD_OK.

Referenced by TIM2_Config().

void TIM2_PWMIConfig	(	TIM2_Channel_TypeDef	TIM2_Channel,
		TIM2_ICPolarity_TypeDef	TIM2_ICPolarity,
		TIM2_ICSelection_TypeDef	TIM2_ICSelection,
		TIM2_ICPSC_TypeDef	TIM2_ICPrescaler,
		uint8_t	TIM2_ICFilter
	)

Configures the TIM2 peripheral in PWM Input Mode according to the specified parameters.

Parameters:

TIM2_Channel	specifies the Input Capture Channel from TIM2_Channel_TypeDef.
TIM2_ICPolarity	specifies the Input Capture Polarity from TIM2_ICPolarity_TypeDef.
TIM2_ICSelection	specifies the Input Capture Selection from TIM2_ICSelection_TypeDef.
TIM2_ICPrescaler	specifies the Input Capture Prescaler from TIM2_ICPSC_TypeDef.
TIM2_ICFilter	specifies the Input Capture Filter value (value can be an integer from 0x00 to 0x0F).

Return values:

None

Definition at line 266 of file stm8s_tim2.c.

References assert_param, IS_TIM2_IC_POLARITY_OK, IS_TIM2_IC_PRESCALER_OK, IS_TIM2_IC_SELECTION_OK, IS_TIM2_PWMI_CHANNEL_OK, TI1_Config(), TI2_Config(), TIM2_CHANNEL_1, TIM2_ICPOLARITY_FALLING, TIM2_ICPOLARITY_RISING, TIM2_ICSELECTION_DIRECTTI, TIM2_ICSELECTION_INDIRECTTI, TIM2_SetIC1Prescaler(), and TIM2_SetIC2Prescaler().

void TIM2_SelectOCxM	(	TIM2_Channel_TypeDef	TIM2_Channel,
		TIM2_OCMode_TypeDef	TIM2_OCMode
	)

Selects the TIM2 Output Compare Mode.

This function disables the selected channel before changing the Output Compare Mode. User has to enable this channel using TIM2_CCxCmd and TIM2_CCxNCmd functions.

Parameters:

TIM2_Channel	specifies the TIM2 Channel. This parameter can be one of the following values: TIM2_CHANNEL_1: TIM2 Channel1 TIM2_CHANNEL_2: TIM2 Channel2 TIM2_CHANNEL_3: TIM2 Channel3
TIM2_OCMode	specifies the TIM2 Output Compare Mode. This paramter can be one of the following values: TIM2_OCMODE_TIMING TIM2_OCMODE_ACTIVE TIM2_OCMODE_TOGGLE TIM2_OCMODE_PWM1 TIM2_OCMODE_PWM2 TIM2_FORCEDACTION_ACTIVE TIM2_FORCEDACTION_INACTIVE

Return values:

None

Definition at line 810 of file stm8s_tim2.c.

References assert_param, IS_TIM2_CHANNEL_OK, IS_TIM2_OCM_OK, TIM2_CCER1_CC1E, TIM2_CCER1_CC2E, TIM2_CCER2_CC3E, TIM2_CCMR_OCM, TIM2_CHANNEL_1, and TIM2_CHANNEL_2.

void TIM2_SelectOnePulseMode ( TIM2_OPMode_TypeDef TIM2_OPMode )

Selects the TIM2�s One Pulse Mode.

Parameters:

TIM2_OPMode

specifies the OPM Mode to be used. This parameter can be one of the following values

TIM2_OPMODE_SINGLE
TIM2_OPMODE_REPETITIVE

Return values:

None

Definition at line 440 of file stm8s_tim2.c.

References assert_param, IS_TIM2_OPM_MODE_OK, TIM2_CR1_OPM, and TIM2_OPMODE_REPETITIVE.

void TIM2_SetAutoreload ( uint16_t Autoreload )

Sets the TIM2 Autoreload Register value.

Parameters:

Autoreload specifies the Autoreload register new value. This parameter is between 0x0000 and 0xFFFF.

Return values:

None

Definition at line 864 of file stm8s_tim2.c.

void TIM2_SetCompare1 ( uint16_t Compare1 )

Sets the TIM2 Capture Compare1 Register value.

Parameters:

Compare1 specifies the Capture Compare1 register new value. This parameter is between 0x0000 and 0xFFFF.

Return values:

None

Definition at line 877 of file stm8s_tim2.c.

void TIM2_SetCompare2 ( uint16_t Compare2 )

Sets the TIM2 Capture Compare2 Register value.

Parameters:

Compare2 specifies the Capture Compare2 register new value. This parameter is between 0x0000 and 0xFFFF.

Return values:

None

Definition at line 890 of file stm8s_tim2.c.

void TIM2_SetCompare3 ( uint16_t Compare3 )

Sets the TIM2 Capture Compare3 Register value.

Parameters:

Compare3 specifies the Capture Compare3 register new value. This parameter is between 0x0000 and 0xFFFF.

Return values:

None

Definition at line 903 of file stm8s_tim2.c.

void TIM2_SetCounter ( uint16_t Counter )

Sets the TIM2 Counter Register value.

Parameters:

Counter specifies the Counter register new value. This parameter is between 0x0000 and 0xFFFF.

Return values:

None

Definition at line 851 of file stm8s_tim2.c.

void TIM2_SetIC1Prescaler ( TIM2_ICPSC_TypeDef TIM2_IC1Prescaler )

Sets the TIM2 Input Capture 1 Prescaler.

Parameters:

TIM2_IC1Prescaler

specifies the Input Capture prescaler new value This parameter can be one of the following values:

TIM2_ICPSC_DIV1: no prescaler
TIM2_ICPSC_DIV2: capture is done once every 2 events
TIM2_ICPSC_DIV4: capture is done once every 4 events
TIM2_ICPSC_DIV8: capture is done once every 8 events

Return values:

None

Definition at line 920 of file stm8s_tim2.c.

References assert_param, IS_TIM2_IC_PRESCALER_OK, and TIM2_CCMR_ICxPSC.

Referenced by TIM2_ICInit(), and TIM2_PWMIConfig().

void TIM2_SetIC2Prescaler ( TIM2_ICPSC_TypeDef TIM2_IC2Prescaler )

Sets the TIM2 Input Capture 2 prescaler.

Parameters:

TIM2_IC2Prescaler

specifies the Input Capture prescaler new value This parameter can be one of the following values:

TIM2_ICPSC_DIV1: no prescaler
TIM2_ICPSC_DIV2: capture is done once every 2 events
TIM2_ICPSC_DIV4: capture is done once every 4 events
TIM2_ICPSC_DIV8: capture is done once every 8 events

Return values:

None

Definition at line 940 of file stm8s_tim2.c.

References assert_param, IS_TIM2_IC_PRESCALER_OK, and TIM2_CCMR_ICxPSC.

Referenced by TIM2_ICInit(), and TIM2_PWMIConfig().

void TIM2_SetIC3Prescaler ( TIM2_ICPSC_TypeDef TIM2_IC3Prescaler )

Sets the TIM2 Input Capture 3 prescaler.

Parameters:

TIM2_IC3Prescaler

specifies the Input Capture prescaler new value This parameter can be one of the following values:

TIM2_ICPSC_DIV1: no prescaler
TIM2_ICPSC_DIV2: capture is done once every 2 events
TIM2_ICPSC_DIV4: capture is done once every 4 events
TIM2_ICPSC_DIV8: capture is done once every 8 events

Return values:

None

Definition at line 960 of file stm8s_tim2.c.

References assert_param, IS_TIM2_IC_PRESCALER_OK, and TIM2_CCMR_ICxPSC.

Referenced by TIM2_ICInit().

void TIM2_TimeBaseInit	(	TIM2_Prescaler_TypeDef	TIM2_Prescaler,
		uint16_t	TIM2_Period
	)

Initializes the TIM2 Time Base Unit according to the specified parameters.

Parameters:

TIM2_Prescaler	specifies the Prescaler from TIM2_Prescaler_TypeDef.
TIM2_Period	specifies the Period value.

Return values:

None

Definition at line 89 of file stm8s_tim2.c.

Referenced by TIM2_Config().

void TIM2_UpdateDisableConfig ( FunctionalState NewState )

Enables or Disables the TIM2 Update event.

Parameters:

NewState new state of the TIM2 peripheral Preload register. This parameter can be ENABLE or DISABLE.

Return values:

None

Definition at line 392 of file stm8s_tim2.c.

References assert_param, DISABLE, IS_FUNCTIONALSTATE_OK, and TIM2_CR1_UDIS.

void TIM2_UpdateRequestConfig ( TIM2_UpdateSource_TypeDef TIM2_UpdateSource )

Selects the TIM2 Update Request Interrupt source.

Parameters:

TIM2_UpdateSource

specifies the Update source. This parameter can be one of the following values

TIM2_UPDATESOURCE_REGULAR
TIM2_UPDATESOURCE_GLOBAL

Return values:

None

Definition at line 416 of file stm8s_tim2.c.

References assert_param, IS_TIM2_UPDATE_SOURCE_OK, TIM2_CR1_URS, and TIM2_UPDATESOURCE_GLOBAL.

STM8S/A Standard Peripherals Firmware Library: TIM2_Public_Functions

STM8S/A

Functions

Function Documentation

Get in touch