STM8S/A Standard Peripherals Firmware Library: Communication between UART1 and UART3 using interrupts

  ******************** (C)COPYRIGHT 2014 STMicroelectronics *******************
  * @file    UART1/UART1_Interrupt/readme.txt
  * @author  MCD Application Team
  * @version V2.2.0
  * @date    30-September-2014
  * @brief   Description of the communication between UART1 and UART3 using 
  *          interrupts Example.
  ******************************************************************************
  *
  * Licensed under MCD-ST Liberty SW License Agreement V2, (the "License");
  * You may not use this file except in compliance with the License.
  * You may obtain a copy of the License at:
  *
  *        http://www.st.com/software_license_agreement_liberty_v2
  *
  * Unless required by applicable law or agreed to in writing, software 
  * distributed under the License is distributed on an "AS IS" BASIS, 
  * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
  * See the License for the specific language governing permissions and
  * limitations under the License.
  *
  ******************************************************************************
  

Example description

This example provides a basic communication between UART1 and UART3 using interrupts. UART3 sends TxBuffer2 to UART1 which sends TxBuffer1 to UART3. The data received by UART1 and UART3 are stored respectively in RxBuffer1 and RxBuffer2. The data transfer is managed in UART1_TX_IRQHandler,UART1_RX_IRQHandler,UART3_TX_IRQHandler and UART3_RX_IRQHandler in stm8s_it.c file.

The UART1 and UART3 are configured as follows:

• BaudRate = 9600 baud
• Word Length = 8 Bits
• One Stop Bit
• No parity
• Receive and transmit enabled
• UART1 Clock disabled

Directory contents

• UART1\UART1_Interrupt\main.c Main file containing the "main" function
• UART1\UART1_Interrupt\main.h Main functions prototype
• UART1\UART1_Interrupt\stm8s_conf.h Library Configuration file
• UART1\UART1_Interrupt\stm8s_it.c Interrupt routines source
• UART1\UART1_Interrupt\stm8s_it.h Interrupt routines declaration

Hardware and Software environment

• This example runs on STM8S and STM8A High density devices only.

• This example has been tested with STMicroelectronics STM8/128-EVAL evaluation board and can be easily tailored to any other development board.

• STM8/128-EVAL Set-up
  • Connect UART1_Tx(PA.05) to UART3_Rx(PD.06) and UART1_Rx(PA.04) to UART3_Tx(PD.05) or connect a null-modem female/female RS232 cable between CN15 and CN13.

How to use it ?

In order to make the program work, you must do the following :

• Copy all source files from this example folder to the template folder under Project
• Open your preferred toolchain
• Rebuild all files and load your image into target memory
• Run the example
• Communication result in Receiver/ Transmitter modes can be checked respectively via TransferStatus2 and TransferStatus1 variables.

Note:

• High-Density STM8A devices are the STM8AF52xx STM8AF6269/8x/Ax, STM8AF51xx, and STM8AF6169/7x/8x/9x/Ax microcontrollers where the Flash memory density ranges between 32 to 128 Kbytes
• Medium-Density STM8A devices are the STM8AF622x/4x, STM8AF6266/68, STM8AF612x/4x, and STM8AF6166/68 microcontrollers where the Flash memory density ranges between 8 to 32 Kbytes
• High-Density STM8S devices are the STM8S207xx, STM8S007 and STM8S208xx microcontrollers where the Flash memory density ranges between 32 to 128 Kbytes.
• Medium-Density STM8S devices are the STM8S105x and STM8S005 microcontrollers where the Flash memory density ranges between 16 to 32-Kbytes.
• Low-Density STM8S devices are the STM8S103xx, STM8S003 and STM8S903xx microcontrollers where the Flash density is 8 Kbytes.

© COPYRIGHT STMicroelectronics