Functions
static void	TI1_Config (uint8_t TIM5_ICPolarity, uint8_t TIM5_ICSelection, uint8_t TIM5_ICFilter)
	Configure the TI1 as Input.
static void	TI2_Config (uint8_t TIM5_ICPolarity, uint8_t TIM5_ICSelection, uint8_t TIM5_ICFilter)
	Configure the TI2 as Input.
static void	TI3_Config (uint8_t TIM5_ICPolarity, uint8_t TIM5_ICSelection, uint8_t TIM5_ICFilter)
	Configure the TI3 as Input.
void	TIM5_ARRPreloadConfig (FunctionalState NewState)
	Enables or disables TIM5 peripheral Preload register on ARR.
void	TIM5_CCxCmd (TIM5_Channel_TypeDef TIM5_Channel, FunctionalState NewState)
	Enables or disables the TIM5 Capture Compare Channel x.
void	TIM5_ClearFlag (TIM5_FLAG_TypeDef TIM5_FLAG)
	Clears the TIM5�s pending flags.
void	TIM5_ClearITPendingBit (TIM5_IT_TypeDef TIM5_IT)
	Clears the TIM5's interrupt pending bits.
void	TIM5_Cmd (FunctionalState NewState)
	Enables or disables the TIM5 peripheral.
void	TIM5_DeInit (void)
	Deinitializes the TIM5 peripheral registers to their default reset values.
void	TIM5_EncoderInterfaceConfig (TIM5_EncoderMode_TypeDef TIM5_EncoderMode, TIM5_ICPolarity_TypeDef TIM5_IC1Polarity, TIM5_ICPolarity_TypeDef TIM5_IC2Polarity)
	Configures the TIM5 Encoder Interface.
void	TIM5_ForcedOC1Config (TIM5_ForcedAction_TypeDef TIM5_ForcedAction)
	Forces the TIM5 Channel1 output waveform to active or inactive level.
void	TIM5_ForcedOC2Config (TIM5_ForcedAction_TypeDef TIM5_ForcedAction)
	Forces the TIM5 Channel2 output waveform to active or inactive level.
void	TIM5_ForcedOC3Config (TIM5_ForcedAction_TypeDef TIM5_ForcedAction)
	Forces the TIM5 Channel3 output waveform to active or inactive level.
void	TIM5_GenerateEvent (TIM5_EventSource_TypeDef TIM5_EventSource)
	Configures the TIM5 event to be generated by software.
uint16_t	TIM5_GetCapture1 (void)
	Gets the TIM5 Input Capture 1 value.
uint16_t	TIM5_GetCapture2 (void)
	Gets the TIM5 Input Capture 2 value.
uint16_t	TIM5_GetCapture3 (void)
	Gets the TIM5 Input Capture 3 value.
uint16_t	TIM5_GetCounter (void)
	Gets the TIM5 Counter value.
FlagStatus	TIM5_GetFlagStatus (TIM5_FLAG_TypeDef TIM5_FLAG)
	Checks whether the specified TIM5 flag is set or not.
ITStatus	TIM5_GetITStatus (TIM5_IT_TypeDef TIM5_IT)
	Checks whether the TIM5 interrupt has occurred or not.
TIM5_Prescaler_TypeDef	TIM5_GetPrescaler (void)
	Gets the TIM5 Prescaler value.
void	TIM5_ICInit (TIM5_Channel_TypeDef TIM5_Channel, TIM5_ICPolarity_TypeDef TIM5_ICPolarity, TIM5_ICSelection_TypeDef TIM5_ICSelection, TIM5_ICPSC_TypeDef TIM5_ICPrescaler, uint8_t TIM5_ICFilter)
	Initializes the TIM5 peripheral according to the specified parameters.
void	TIM5_InternalClockConfig (void)
	Enables the TIM5 internal Clock.
void	TIM5_ITConfig (TIM5_IT_TypeDef TIM5_IT, FunctionalState NewState)
	Enables or disables the specified TIM5 interrupts.
void	TIM5_OC1Init (TIM5_OCMode_TypeDef TIM5_OCMode, TIM5_OutputState_TypeDef TIM5_OutputState, uint16_t TIM5_Pulse, TIM5_OCPolarity_TypeDef TIM5_OCPolarity)
	Initializes the TIM5 Channel1 according to the specified parameters.
void	TIM5_OC1PolarityConfig (TIM5_OCPolarity_TypeDef TIM5_OCPolarity)
	Configures the TIM5 Channel 1 polarity.
void	TIM5_OC1PreloadConfig (FunctionalState NewState)
	Enables or disables the TIM5 peripheral Preload Register on CCR1.
void	TIM5_OC2Init (TIM5_OCMode_TypeDef TIM5_OCMode, TIM5_OutputState_TypeDef TIM5_OutputState, uint16_t TIM5_Pulse, TIM5_OCPolarity_TypeDef TIM5_OCPolarity)
	Initializes the TIM5 Channel2 according to the specified parameters.
void	TIM5_OC2PolarityConfig (TIM5_OCPolarity_TypeDef TIM5_OCPolarity)
	Configures the TIM5 Channel 2 polarity.
void	TIM5_OC2PreloadConfig (FunctionalState NewState)
	Enables or disables the TIM5 peripheral Preload Register on CCR2.
void	TIM5_OC3Init (TIM5_OCMode_TypeDef TIM5_OCMode, TIM5_OutputState_TypeDef TIM5_OutputState, uint16_t TIM5_Pulse, TIM5_OCPolarity_TypeDef TIM5_OCPolarity)
	Initializes the TIM5 Channel3 according to the specified parameters.
void	TIM5_OC3PolarityConfig (TIM5_OCPolarity_TypeDef TIM5_OCPolarity)
	Configures the TIM5 Channel 3 polarity.
void	TIM5_OC3PreloadConfig (FunctionalState NewState)
	Enables or disables the TIM5 peripheral Preload Register on CCR3.
void	TIM5_PrescalerConfig (TIM5_Prescaler_TypeDef Prescaler, TIM5_PSCReloadMode_TypeDef TIM5_PSCReloadMode)
	Configures the TIM5 Prescaler.
void	TIM5_PWMIConfig (TIM5_Channel_TypeDef TIM5_Channel, TIM5_ICPolarity_TypeDef TIM5_ICPolarity, TIM5_ICSelection_TypeDef TIM5_ICSelection, TIM5_ICPSC_TypeDef TIM5_ICPrescaler, uint8_t TIM5_ICFilter)
	Configures the TIM5 peripheral in PWM Input Mode according to the specified parameters.
void	TIM5_SelectInputTrigger (TIM5_TS_TypeDef TIM5_InputTriggerSource)
	Selects the TIM5 Input Trigger source.
void	TIM5_SelectOCxM (TIM5_Channel_TypeDef TIM5_Channel, TIM5_OCMode_TypeDef TIM5_OCMode)
	Selects the TIM5 Output Compare Mode.
void	TIM5_SelectOnePulseMode (TIM5_OPMode_TypeDef TIM5_OPMode)
	Selects the TIM5�s One Pulse Mode.
void	TIM5_SelectOutputTrigger (TIM5_TRGOSource_TypeDef TIM5_TRGOSource)
	Selects the TIM5 Trigger Output Mode.
void	TIM5_SelectSlaveMode (TIM5_SlaveMode_TypeDef TIM5_SlaveMode)
	Selects the TIM5 Slave Mode.
void	TIM5_SetAutoreload (uint16_t Autoreload)
	Sets the TIM5 Autoreload Register value.
void	TIM5_SetCompare1 (uint16_t Compare1)
	Sets the TIM5 Capture Compare1 Register value.
void	TIM5_SetCompare2 (uint16_t Compare2)
	Sets the TIM5 Capture Compare2 Register value.
void	TIM5_SetCompare3 (uint16_t Compare3)
	Sets the TIM5 Capture Compare3 Register value.
void	TIM5_SetCounter (uint16_t Counter)
	Sets the TIM5 Counter Register value.
void	TIM5_SetIC1Prescaler (TIM5_ICPSC_TypeDef TIM5_IC1Prescaler)
	Sets the TIM5 Input Capture 1 prescaler.
void	TIM5_SetIC2Prescaler (TIM5_ICPSC_TypeDef TIM5_IC2Prescaler)
	Sets the TIM5 Input Capture 2 prescaler.
void	TIM5_SetIC3Prescaler (TIM5_ICPSC_TypeDef TIM5_IC3Prescaler)
	Sets the TIM5 Input Capture 3 prescaler.
void	TIM5_TimeBaseInit (TIM5_Prescaler_TypeDef TIM5_Prescaler, uint16_t TIM5_Period)
	Initializes the TIM5 Time Base Unit according to the specified parameters.
void	TIM5_UpdateDisableConfig (FunctionalState NewState)
	Enables or Disables the TIM5 Update event.
void	TIM5_UpdateRequestConfig (TIM5_UpdateSource_TypeDef TIM5_UpdateSource)
	Selects the TIM5 Update Request Interrupt source.

Function Documentation

static void TI1_Config	(	uint8_t	TIM5_ICPolarity,
		uint8_t	TIM5_ICSelection,
		uint8_t	TIM5_ICFilter
	)		`[static]`

Configure the TI1 as Input.

Parameters:

TIM5_ICPolarity	The Input Polarity. This parameter can be one of the following values: TIM5_ICPOLARITY_FALLING TIM5_ICPOLARITY_RISING
TIM5_ICSelection	specifies the input to be used. This parameter can be one of the following values: TIM5_ICSELECTION_DIRECTTI: TIM5 Input 1 is selected to be connected to IC1. TIM5_ICSELECTION_INDIRECTTI: TIM5 Input 1 is selected to be connected to IC2.
TIM5_ICFilter	Specifies the Input Capture Filter. This parameter must be a value between 0x00 and 0x0F.

Return values:

None

Definition at line 1161 of file stm8s_tim5.c.

References TIM5_CCER1_CC1E, TIM5_CCER1_CC1P, TIM5_CCMR_CCxS, TIM5_CCMR_ICxF, and TIM5_ICPOLARITY_RISING.

Referenced by TIM5_ICInit(), and TIM5_PWMIConfig().

static void TI2_Config	(	uint8_t	TIM5_ICPolarity,
		uint8_t	TIM5_ICSelection,
		uint8_t	TIM5_ICFilter
	)		`[static]`

Configure the TI2 as Input.

Parameters:

TIM5_ICPolarity	The Input Polarity. This parameter can be one of the following values: TIM5_ICPOLARITY_FALLING TIM5_ICPOLARITY_RISING
TIM5_ICSelection	specifies the input to be used. This parameter can be one of the following values: TIM5_ICSELECTION_DIRECTTI: TIM5 Input 2 is selected to be connected to IC2. TIM5_ICSELECTION_INDIRECTTI: TIM5 Input 2 is selected to be connected to IC1.
TIM5_ICFilter	Specifies the Input Capture Filter. This parameter must be a value between 0x00 and 0x0F.

Return values:

None

Definition at line 1201 of file stm8s_tim5.c.

References TIM5_CCER1_CC2E, TIM5_CCER1_CC2P, TIM5_CCMR_CCxS, TIM5_CCMR_ICxF, and TIM5_ICPOLARITY_RISING.

Referenced by TIM5_ICInit(), and TIM5_PWMIConfig().

static void TI3_Config	(	uint8_t	TIM5_ICPolarity,
		uint8_t	TIM5_ICSelection,
		uint8_t	TIM5_ICFilter
	)		`[static]`

Configure the TI3 as Input.

Parameters:

TIM5_ICPolarity	The Input Polarity. This parameter can be one of the following values: TIM5_ICPOLARITY_FALLING TIM5_ICPOLARITY_RISING
TIM5_ICSelection	specifies the input to be used. This parameter can be one of the following values: TIM5_ICSELECTION_DIRECTTI: TIM5 Input 3 is selected to be connected to IC3.
TIM5_ICFilter	Specifies the Input Capture Filter. This parameter must be a value between 0x00 and 0x0F.

Return values:

None

Definition at line 1241 of file stm8s_tim5.c.

References TIM5_CCER2_CC3E, TIM5_CCER2_CC3P, TIM5_CCMR_CCxS, TIM5_CCMR_ICxF, and TIM5_ICPOLARITY_RISING.

Referenced by TIM5_ICInit().

void TIM5_ARRPreloadConfig ( FunctionalState NewState )

Enables or disables TIM5 peripheral Preload register on ARR.

Parameters:

NewState new state of the TIM5 peripheral Preload register. This parameter can be ENABLE or DISABLE.

Return values:

None

Definition at line 556 of file stm8s_tim5.c.

References assert_param, DISABLE, IS_FUNCTIONALSTATE_OK, and TIM5_CR1_ARPE.

void TIM5_CCxCmd	(	TIM5_Channel_TypeDef	TIM5_Channel,
		FunctionalState	NewState
	)

Enables or disables the TIM5 Capture Compare Channel x.

Parameters:

TIM5_Channel	specifies the TIM5 Channel. This parameter can be one of the following values: TIM5_Channel1: TIM5 Channel1 TIM5_Channel2: TIM5 Channel2 TIM5_Channel3: TIM5 Channel3
NewState	specifies the TIM5 Channel CCxE bit new state. This parameter can be: ENABLE or DISABLE.

Return values:

None

Definition at line 741 of file stm8s_tim5.c.

References assert_param, DISABLE, IS_FUNCTIONALSTATE_OK, IS_TIM5_CHANNEL_OK, TIM5_CCER1_CC1E, TIM5_CCER1_CC2E, TIM5_CCER2_CC3E, TIM5_CHANNEL_1, and TIM5_CHANNEL_2.

void TIM5_ClearFlag ( TIM5_FLAG_TypeDef TIM5_FLAG )

Clears the TIM5�s pending flags.

Parameters:

TIM5_FLAG

specifies the flag to clear. This parameter can be one of the following values:

TIM5_FLAG_UPDATE: TIM5 update Flag
TIM5_FLAG_CC1: TIM5 Capture Compare 1 Flag
TIM5_FLAG_CC2: TIM5 Capture Compare 2 Flag
TIM5_FLAG_CC3: TIM5 Capture Compare 3 Flag
TIM5_FLAG_CC1OF: TIM5 Capture Compare 1 overcapture Flag
TIM5_FLAG_CC2OF: TIM5 Capture Compare 2 overcapture Flag
TIM5_FLAG_CC3OF: TIM5 Capture Compare 3 overcapture Flag

Return values:

None.

Definition at line 1082 of file stm8s_tim5.c.

References assert_param, and IS_TIM5_CLEAR_FLAG_OK.

void TIM5_ClearITPendingBit ( TIM5_IT_TypeDef TIM5_IT )

Clears the TIM5's interrupt pending bits.

Parameters:

TIM5_IT

specifies the pending bit to clear. This parameter can be one of the following values:

TIM5_IT_UPDATE: TIM5 update Interrupt source
TIM5_IT_CC1: TIM5 Capture Compare 1 Interrupt source
TIM5_IT_CC2: TIM5 Capture Compare 2 Interrupt source
TIM5_IT_CC3: TIM5 Capture Compare 3 Interrupt source

Return values:

None.

Definition at line 1136 of file stm8s_tim5.c.

References assert_param, and IS_TIM5_IT_OK.

void TIM5_Cmd ( FunctionalState NewState )

Enables or disables the TIM5 peripheral.

Parameters:

NewState new state of the TIM5 peripheral.This parameter can be ENABLE or DISABLE.

Return values:

None

Definition at line 334 of file stm8s_tim5.c.

References assert_param, DISABLE, IS_FUNCTIONALSTATE_OK, and TIM5_CR1_CEN.

void TIM5_DeInit ( void )

Deinitializes the TIM5 peripheral registers to their default reset values.

Parameters:

None

Return values:

None

Definition at line 52 of file stm8s_tim5.c.

Referenced by TIM5_Config().

void TIM5_EncoderInterfaceConfig	(	TIM5_EncoderMode_TypeDef	TIM5_EncoderMode,
		TIM5_ICPolarity_TypeDef	TIM5_IC1Polarity,
		TIM5_ICPolarity_TypeDef	TIM5_IC2Polarity
	)

Configures the TIM5 Encoder Interface.

Parameters:

TIM5_EncoderMode	: Specifies the TIM5 Encoder Mode. This parameter can be one of the TIM5_EncoderMode_TypeDef enumeration.
TIM5_IC1Polarity	: Specifies the IC1 Polarity. This parameter can be one of the TIM5_ICPolarity_TypeDef enumeration.
TIM5_IC2Polarity	: Specifies the IC2 Polarity. This parameter can be one of the TIM5_ICPolarity_TypeDef enumeration.

Return values:

None

Definition at line 1357 of file stm8s_tim5.c.

References assert_param, IS_TIM5_ENCODER_MODE_OK, IS_TIM5_IC_POLARITY_OK, TIM5_CCER1_CC1P, TIM5_CCER1_CC2P, TIM5_CCMR_CCxS, TIM5_CCMR_TIxDirect_Set, TIM5_ICPOLARITY_FALLING, TIM5_SMCR_MSM, and TIM5_SMCR_TS.

void TIM5_ForcedOC1Config ( TIM5_ForcedAction_TypeDef TIM5_ForcedAction )

Forces the TIM5 Channel1 output waveform to active or inactive level.

Parameters:

TIM5_ForcedAction

specifies the forced Action to be set to the output waveform. This parameter can be one of the following values:

TIM5_FORCEDACTION_ACTIVE: Force active level on OC1REF
TIM5_FORCEDACTION_INACTIVE: Force inactive level on OC1REF.

Return values:

None

Definition at line 502 of file stm8s_tim5.c.

References assert_param, IS_TIM5_FORCED_ACTION_OK, and TIM5_CCMR_OCM.

void TIM5_ForcedOC2Config ( TIM5_ForcedAction_TypeDef TIM5_ForcedAction )

Forces the TIM5 Channel2 output waveform to active or inactive level.

Parameters:

TIM5_ForcedAction

specifies the forced Action to be set to the output waveform. This parameter can be one of the following values:

TIM5_FORCEDACTION_ACTIVE: Force active level on OC2REF
TIM5_FORCEDACTION_INACTIVE: Force inactive level on OC2REF.

Return values:

None

Definition at line 521 of file stm8s_tim5.c.

References assert_param, IS_TIM5_FORCED_ACTION_OK, and TIM5_CCMR_OCM.

void TIM5_ForcedOC3Config ( TIM5_ForcedAction_TypeDef TIM5_ForcedAction )

Forces the TIM5 Channel3 output waveform to active or inactive level.

Parameters:

TIM5_ForcedAction

specifies the forced Action to be set to the output waveform. This parameter can be one of the following values:

TIM5_FORCEDACTION_ACTIVE: Force active level on OC3REF
TIM5_FORCEDACTION_INACTIVE: Force inactive level on OC3REF.

Return values:

None

Definition at line 540 of file stm8s_tim5.c.

References assert_param, IS_TIM5_FORCED_ACTION_OK, and TIM5_CCMR_OCM.

void TIM5_GenerateEvent ( TIM5_EventSource_TypeDef TIM5_EventSource )

Configures the TIM5 event to be generated by software.

Parameters:

TIM5_EventSource

specifies the event source. This parameter can be one of the following values:

TIM5_EVENTSOURCE_UPDATE: TIM5 update Event source
TIM5_EVENTSOURCE_CC1: TIM5 Capture Compare 1 Event source
TIM5_EVENTSOURCE_CC2: TIM5 Capture Compare 2 Event source
TIM5_EVENTSOURCE_CC3: TIM5 Capture Compare 3 Event source

Return values:

None

Definition at line 648 of file stm8s_tim5.c.

References assert_param, and IS_TIM5_EVENT_SOURCE_OK.

uint16_t TIM5_GetCapture1 ( void )

Gets the TIM5 Input Capture 1 value.

Parameters:

None

Return values:

Capture Compare 1 Register value.

Definition at line 970 of file stm8s_tim5.c.

uint16_t TIM5_GetCapture2 ( void )

Gets the TIM5 Input Capture 2 value.

Parameters:

None

Return values:

Capture Compare 2 Register value.

Definition at line 985 of file stm8s_tim5.c.

uint16_t TIM5_GetCapture3 ( void )

Gets the TIM5 Input Capture 3 value.

Parameters:

None

Return values:

Capture Compare 3 Register value.

Definition at line 1000 of file stm8s_tim5.c.

uint16_t TIM5_GetCounter ( void )

Gets the TIM5 Counter value.

Parameters:

None

Return values:

Counter Register value.

Definition at line 1014 of file stm8s_tim5.c.

FlagStatus TIM5_GetFlagStatus ( TIM5_FLAG_TypeDef TIM5_FLAG )

Checks whether the specified TIM5 flag is set or not.

Parameters:

TIM5_FLAG

specifies the flag to check. This parameter can be one of the following values:

TIM5_FLAG_UPDATE: TIM5 update Flag
TIM5_FLAG_CC1: TIM5 Capture Compare 1 Flag
TIM5_FLAG_CC2: TIM5 Capture Compare 2 Flag
TIM5_FLAG_CC3: TIM5 Capture Compare 3 Flag
TIM5_FLAG_CC1OF: TIM5 Capture Compare 1 overcapture Flag
TIM5_FLAG_CC2OF: TIM5 Capture Compare 2 overcapture Flag
TIM5_FLAG_CC3OF: TIM5 Capture Compare 3 overcapture Flag

Return values:

FlagStatus The new state of TIM5_FLAG (SET or RESET).

Definition at line 1047 of file stm8s_tim5.c.

References assert_param, IS_TIM5_GET_FLAG_OK, RESET, and SET.

ITStatus TIM5_GetITStatus ( TIM5_IT_TypeDef TIM5_IT )

Checks whether the TIM5 interrupt has occurred or not.

Parameters:

TIM5_IT

specifies the TIM5 interrupt source to check. This parameter can be one of the following values:

TIM5_IT_UPDATE: TIM5 update Interrupt source
TIM5_IT_CC1: TIM5 Capture Compare 1 Interrupt source
TIM5_IT_CC2: TIM5 Capture Compare 2 Interrupt source
TIM5_IT_CC3: TIM5 Capture Compare 3 Interrupt source

Return values:

ITStatus The new state of the TIM5_IT(SET or RESET).

Definition at line 1103 of file stm8s_tim5.c.

References assert_param, IS_TIM5_GET_IT_OK, RESET, and SET.

TIM5_Prescaler_TypeDef TIM5_GetPrescaler ( void )

Gets the TIM5 Prescaler value.

Parameters:

None

Return values:

Prescaler Register configuration value TIM5_Prescaler_TypeDef .

Definition at line 1028 of file stm8s_tim5.c.

void TIM5_ICInit	(	TIM5_Channel_TypeDef	TIM5_Channel,
		TIM5_ICPolarity_TypeDef	TIM5_ICPolarity,
		TIM5_ICSelection_TypeDef	TIM5_ICSelection,
		TIM5_ICPSC_TypeDef	TIM5_ICPrescaler,
		uint8_t	TIM5_ICFilter
	)

Initializes the TIM5 peripheral according to the specified parameters.

Parameters:

TIM5_Channel	specifies the Input Capture Channel from TIM5_Channel_TypeDef.
TIM5_ICPolarity	specifies the Input Capture Polarity from TIM5_ICPolarity_TypeDef.
TIM5_ICSelection	specifies theInput Capture Selection from TIM5_ICSelection_TypeDef.
TIM5_ICPrescaler	specifies the Input Capture Prescaler from TIM5_ICPSC_TypeDef.
TIM5_ICFilter	specifies the Input Capture Filter value (value can be an integer from 0x00 to 0x0F).

Return values:

None

Definition at line 207 of file stm8s_tim5.c.

References assert_param, IS_TIM5_CHANNEL_OK, IS_TIM5_IC_FILTER_OK, IS_TIM5_IC_POLARITY_OK, IS_TIM5_IC_PRESCALER_OK, IS_TIM5_IC_SELECTION_OK, TI1_Config(), TI2_Config(), TI3_Config(), TIM5_CHANNEL_1, TIM5_CHANNEL_2, TIM5_SetIC1Prescaler(), TIM5_SetIC2Prescaler(), and TIM5_SetIC3Prescaler().

void TIM5_InternalClockConfig ( void )

Enables the TIM5 internal Clock.

Parameters:: None

Return values:

None

Definition at line 1271 of file stm8s_tim5.c.

References TIM5_SMCR_SMS.

void TIM5_ITConfig	(	TIM5_IT_TypeDef	TIM5_IT,
		FunctionalState	NewState
	)

Enables or disables the specified TIM5 interrupts.

Parameters:

NewState	new state of the TIM5 peripheral. This parameter can be: ENABLE or DISABLE.
TIM5_IT	specifies the TIM5 interrupts sources to be enabled or disabled. This parameter can be any combination of the following values: TIM5_IT_UPDATE: TIM5 update Interrupt source TIM5_IT_CC1: TIM5 Capture Compare 1 Interrupt source TIM5_IT_CC2: TIM5 Capture Compare 2 Interrupt source TIM5_IT_CC3: TIM5 Capture Compare 3 Interrupt source
NewState	new state of the TIM5 peripheral.

Return values:

None

Definition at line 363 of file stm8s_tim5.c.

References assert_param, DISABLE, IS_FUNCTIONALSTATE_OK, and IS_TIM5_IT_OK.

void TIM5_OC1Init	(	TIM5_OCMode_TypeDef	TIM5_OCMode,
		TIM5_OutputState_TypeDef	TIM5_OutputState,
		uint16_t	TIM5_Pulse,
		TIM5_OCPolarity_TypeDef	TIM5_OCPolarity
	)

Initializes the TIM5 Channel1 according to the specified parameters.

Parameters:

TIM5_OCMode	specifies the Output Compare mode from TIM5_OCMode_TypeDef.
TIM5_OutputState	specifies the Output State from TIM5_OutputState_TypeDef.
TIM5_Pulse	specifies the Pulse width value.
TIM5_OCPolarity	specifies the Output Compare Polarity from TIM5_OCPolarity_TypeDef.

Return values:

None

Definition at line 108 of file stm8s_tim5.c.

References assert_param, IS_TIM5_OC_MODE_OK, IS_TIM5_OC_POLARITY_OK, IS_TIM5_OUTPUT_STATE_OK, TIM5_CCER1_CC1E, TIM5_CCER1_CC1P, and TIM5_CCMR_OCM.

void TIM5_OC1PolarityConfig ( TIM5_OCPolarity_TypeDef TIM5_OCPolarity )

Configures the TIM5 Channel 1 polarity.

Parameters:

TIM5_OCPolarity

specifies the OC1 Polarity. This parameter can be one of the following values:

TIM5_OCPOLARITY_LOW: Output Compare active low
TIM5_OCPOLARITY_HIGH: Output Compare active high

Return values:

None

Definition at line 665 of file stm8s_tim5.c.

References assert_param, IS_TIM5_OC_POLARITY_OK, TIM5_CCER1_CC1P, and TIM5_OCPOLARITY_HIGH.

void TIM5_OC1PreloadConfig ( FunctionalState NewState )

Enables or disables the TIM5 peripheral Preload Register on CCR1.

Parameters:

NewState new state of the Capture Compare Preload register. This parameter can be ENABLE or DISABLE.

Return values:

None

Definition at line 578 of file stm8s_tim5.c.

References assert_param, DISABLE, IS_FUNCTIONALSTATE_OK, and TIM5_CCMR_OCxPE.

void TIM5_OC2Init	(	TIM5_OCMode_TypeDef	TIM5_OCMode,
		TIM5_OutputState_TypeDef	TIM5_OutputState,
		uint16_t	TIM5_Pulse,
		TIM5_OCPolarity_TypeDef	TIM5_OCPolarity
	)

Initializes the TIM5 Channel2 according to the specified parameters.

Parameters:

TIM5_OCMode	specifies the Output Compare mode from TIM5_OCMode_TypeDef.
TIM5_OutputState	specifies the Output State from TIM5_OutputState_TypeDef.
TIM5_Pulse	specifies the Pulse width value.
TIM5_OCPolarity	specifies the Output Compare Polarity from TIM5_OCPolarity_TypeDef.

Return values:

None

Definition at line 141 of file stm8s_tim5.c.

References assert_param, IS_TIM5_OC_MODE_OK, IS_TIM5_OC_POLARITY_OK, IS_TIM5_OUTPUT_STATE_OK, TIM5_CCER1_CC2E, TIM5_CCER1_CC2P, and TIM5_CCMR_OCM.

void TIM5_OC2PolarityConfig ( TIM5_OCPolarity_TypeDef TIM5_OCPolarity )

Configures the TIM5 Channel 2 polarity.

Parameters:

TIM5_OCPolarity

specifies the OC2 Polarity. This parameter can be one of the following values:

TIM5_OCPOLARITY_LOW: Output Compare active low
TIM5_OCPOLARITY_HIGH: Output Compare active high

Return values:

None

Definition at line 690 of file stm8s_tim5.c.

References assert_param, IS_TIM5_OC_POLARITY_OK, TIM5_CCER1_CC2P, and TIM5_OCPOLARITY_HIGH.

void TIM5_OC2PreloadConfig ( FunctionalState NewState )

Enables or disables the TIM5 peripheral Preload Register on CCR2.

Parameters:

NewState new state of the Capture Compare Preload register. This parameter can be ENABLE or DISABLE.

Return values:

None

Definition at line 600 of file stm8s_tim5.c.

References assert_param, DISABLE, IS_FUNCTIONALSTATE_OK, and TIM5_CCMR_OCxPE.

void TIM5_OC3Init	(	TIM5_OCMode_TypeDef	TIM5_OCMode,
		TIM5_OutputState_TypeDef	TIM5_OutputState,
		uint16_t	TIM5_Pulse,
		TIM5_OCPolarity_TypeDef	TIM5_OCPolarity
	)

Initializes the TIM5 Channel3 according to the specified parameters.

Parameters:

TIM5_OCMode	specifies the Output Compare mode from TIM5_OCMode_TypeDef.
TIM5_OutputState	specifies the Output State from TIM5_OutputState_TypeDef.
TIM5_Pulse	specifies the Pulse width value.
TIM5_OCPolarity	specifies the Output Compare Polarity from TIM5_OCPolarity_TypeDef.

Return values:

None

Definition at line 175 of file stm8s_tim5.c.

References assert_param, IS_TIM5_OC_MODE_OK, IS_TIM5_OC_POLARITY_OK, IS_TIM5_OUTPUT_STATE_OK, TIM5_CCER2_CC3E, TIM5_CCER2_CC3P, and TIM5_CCMR_OCM.

void TIM5_OC3PolarityConfig ( TIM5_OCPolarity_TypeDef TIM5_OCPolarity )

Configures the TIM5 Channel 3 polarity.

Parameters:

TIM5_OCPolarity

specifies the OC3 Polarity. This parameter can be one of the following values:

TIM5_OCPOLARITY_LOW: Output Compare active low
TIM5_OCPOLARITY_HIGH: Output Compare active high

Return values:

None

Definition at line 714 of file stm8s_tim5.c.

References assert_param, IS_TIM5_OC_POLARITY_OK, TIM5_CCER2_CC3P, and TIM5_OCPOLARITY_HIGH.

void TIM5_OC3PreloadConfig ( FunctionalState NewState )

Enables or disables the TIM5 peripheral Preload Register on CCR3.

Parameters:

NewState new state of the Capture Compare Preload register. This parameter can be ENABLE or DISABLE.

Return values:

None

Definition at line 622 of file stm8s_tim5.c.

References assert_param, DISABLE, IS_FUNCTIONALSTATE_OK, and TIM5_CCMR_OCxPE.

void TIM5_PrescalerConfig	(	TIM5_Prescaler_TypeDef	Prescaler,
		TIM5_PSCReloadMode_TypeDef	TIM5_PSCReloadMode
	)

Configures the TIM5 Prescaler.

Parameters:

Prescaler

specifies the Prescaler Register value This parameter can be one of the following values

TIM5_PRESCALER_1
TIM5_PRESCALER_2
TIM5_PRESCALER_4
TIM5_PRESCALER_8
TIM5_PRESCALER_16
TIM5_PRESCALER_32
TIM5_PRESCALER_64
TIM5_PRESCALER_128
TIM5_PRESCALER_256
TIM5_PRESCALER_512
TIM5_PRESCALER_1024
TIM5_PRESCALER_2048
TIM5_PRESCALER_4096
TIM5_PRESCALER_8192
TIM5_PRESCALER_16384
TIM5_PRESCALER_32768

TIM5_PSCReloadMode

specifies the TIM5 Prescaler Reload mode. This parameter can be one of the following values

TIM5_PSCRELOADMODE_IMMEDIATE: The Prescaler is loaded immediatly.
TIM5_PSCRELOADMODE_UPDATE: The Prescaler is loaded at the update event.

Return values:

None

Definition at line 479 of file stm8s_tim5.c.

References assert_param, IS_TIM5_PRESCALER_OK, and IS_TIM5_PRESCALER_RELOAD_OK.

void TIM5_PWMIConfig	(	TIM5_Channel_TypeDef	TIM5_Channel,
		TIM5_ICPolarity_TypeDef	TIM5_ICPolarity,
		TIM5_ICSelection_TypeDef	TIM5_ICSelection,
		TIM5_ICPSC_TypeDef	TIM5_ICPrescaler,
		uint8_t	TIM5_ICFilter
	)

Configures the TIM5 peripheral in PWM Input Mode according to the specified parameters.

Parameters:

TIM5_Channel	specifies the Input Capture Channel from TIM5_Channel_TypeDef.
TIM5_ICPolarity	specifies the Input Capture Polarity from TIM5_ICPolarity_TypeDef.
TIM5_ICSelection	specifies theInput Capture Selection from TIM5_ICSelection_TypeDef.
TIM5_ICPrescaler	specifies the Input Capture Prescaler from TIM5_ICPSC_TypeDef.
TIM5_ICFilter	specifies the Input Capture Filter value (value can be an integer from 0x00 to 0x0F).

Return values:

None

Definition at line 261 of file stm8s_tim5.c.

References assert_param, IS_TIM5_IC_POLARITY_OK, IS_TIM5_IC_PRESCALER_OK, IS_TIM5_IC_SELECTION_OK, IS_TIM5_PWMI_CHANNEL_OK, TI1_Config(), TI2_Config(), TIM5_CHANNEL_1, TIM5_ICPOLARITY_FALLING, TIM5_ICPOLARITY_RISING, TIM5_ICSELECTION_DIRECTTI, TIM5_ICSELECTION_INDIRECTTI, TIM5_SetIC1Prescaler(), and TIM5_SetIC2Prescaler().

void TIM5_SelectInputTrigger ( TIM5_TS_TypeDef TIM5_InputTriggerSource )

Selects the TIM5 Input Trigger source.

Parameters:

TIM5_InputTriggerSource : Specifies Input Trigger source. This parameter can be one of the TIM5_TS_TypeDef enumeration.

Return values:

None

Definition at line 1331 of file stm8s_tim5.c.

References assert_param, IS_TIM5_TRIGGER_SELECTION_OK, and TIM5_SMCR_TS.

Referenced by TIM5_Config().

void TIM5_SelectOCxM	(	TIM5_Channel_TypeDef	TIM5_Channel,
		TIM5_OCMode_TypeDef	TIM5_OCMode
	)

Selects the TIM5 Output Compare Mode.

This function disables the selected channel before changing the Output Compare Mode. User has to enable this channel using TIM5_CCxCmd and TIM5_CCxNCmd functions.

Parameters:

TIM5_Channel	specifies the TIM5 Channel. This parameter can be one of the following values: TIM5_Channel1: TIM5 Channel1 TIM5_Channel2: TIM5 Channel2 TIM5_Channel3: TIM5 Channel3
TIM5_OCMode	specifies the TIM5 Output Compare Mode. This paramter can be one of the following values: TIM5_OCMODE_TIMING TIM5_OCMODE_ACTIVE TIM5_OCMODE_TOGGLE TIM5_OCMODE_PWM1 TIM5_OCMODE_PWM2 TIM5_FORCEDACTION_ACTIVE TIM5_FORCEDACTION_INACTIVE

Return values:

None

Definition at line 806 of file stm8s_tim5.c.

References assert_param, IS_TIM5_CHANNEL_OK, IS_TIM5_OCM_OK, TIM5_CCER1_CC1E, TIM5_CCER1_CC2E, TIM5_CCER2_CC3E, TIM5_CCMR_OCM, TIM5_CHANNEL_1, and TIM5_CHANNEL_2.

void TIM5_SelectOnePulseMode ( TIM5_OPMode_TypeDef TIM5_OPMode )

Selects the TIM5�s One Pulse Mode.

Parameters:

TIM5_OPMode

specifies the OPM Mode to be used. This parameter can be one of the following values

TIM5_OPMODE_SINGLE
TIM5_OPMODE_REPETITIVE

Return values:

None

Definition at line 435 of file stm8s_tim5.c.

References assert_param, IS_TIM5_OPM_MODE_OK, TIM5_CR1_OPM, and TIM5_OPMODE_REPETITIVE.

void TIM5_SelectOutputTrigger ( TIM5_TRGOSource_TypeDef TIM5_TRGOSource )

Selects the TIM5 Trigger Output Mode.

Parameters:

TIM5_TRGOSource : Specifies the Trigger Output source. This parameter can be one of the TIM5_TRGOSource_TypeDef enumeration.

Return values:

None

Definition at line 1283 of file stm8s_tim5.c.

References assert_param, IS_TIM5_TRGO_SOURCE_OK, and TIM5_CR2_MMS.

void TIM5_SelectSlaveMode ( TIM5_SlaveMode_TypeDef TIM5_SlaveMode )

Selects the TIM5 Slave Mode.

Parameters:

TIM5_SlaveMode : Specifies the TIM5 Slave Mode. This parameter can be one of the TIM5_SlaveMode_TypeDef enumeration.

Return values:

None

Definition at line 1307 of file stm8s_tim5.c.

References assert_param, IS_TIM5_SLAVE_MODE_OK, and TIM5_SMCR_SMS.

Referenced by TIM5_Config().

void TIM5_SetAutoreload ( uint16_t Autoreload )

Sets the TIM5 Autoreload Register value.

Parameters:

Autoreload specifies the Autoreload register new value. This parameter is between 0x0000 and 0xFFFF.

Return values:

None

Definition at line 860 of file stm8s_tim5.c.

void TIM5_SetCompare1 ( uint16_t Compare1 )

Sets the TIM5 Capture Compare1 Register value.

Parameters:

Compare1 specifies the Capture Compare1 register new value. This parameter is between 0x0000 and 0xFFFF.

Return values:

None

Definition at line 873 of file stm8s_tim5.c.

void TIM5_SetCompare2 ( uint16_t Compare2 )

Sets the TIM5 Capture Compare2 Register value.

Parameters:

Compare2 specifies the Capture Compare2 register new value. This parameter is between 0x0000 and 0xFFFF.

Return values:

None

Definition at line 886 of file stm8s_tim5.c.

void TIM5_SetCompare3 ( uint16_t Compare3 )

Sets the TIM5 Capture Compare3 Register value.

Parameters:

Compare3 specifies the Capture Compare3 register new value. This parameter is between 0x0000 and 0xFFFF.

Return values:

None

Definition at line 899 of file stm8s_tim5.c.

void TIM5_SetCounter ( uint16_t Counter )

Sets the TIM5 Counter Register value.

Parameters:

Counter specifies the Counter register new value. This parameter is between 0x0000 and 0xFFFF.

Return values:

None

Definition at line 847 of file stm8s_tim5.c.

void TIM5_SetIC1Prescaler ( TIM5_ICPSC_TypeDef TIM5_IC1Prescaler )

Sets the TIM5 Input Capture 1 prescaler.

Parameters:

TIM5_IC1Prescaler

specifies the Input Capture prescaler new value This parameter can be one of the following values:

TIM5_ICPSC_DIV1: no prescaler
TIM5_ICPSC_DIV2: capture is done once every 2 events
TIM5_ICPSC_DIV4: capture is done once every 4 events
TIM5_ICPSC_DIV8: capture is done once every 8 events

Return values:

None

Definition at line 916 of file stm8s_tim5.c.

References assert_param, IS_TIM5_IC_PRESCALER_OK, and TIM5_CCMR_ICxPSC.

Referenced by TIM5_ICInit(), and TIM5_PWMIConfig().

void TIM5_SetIC2Prescaler ( TIM5_ICPSC_TypeDef TIM5_IC2Prescaler )

Sets the TIM5 Input Capture 2 prescaler.

Parameters:

TIM5_IC2Prescaler

specifies the Input Capture prescaler new value This parameter can be one of the following values:

TIM5_ICPSC_DIV1: no prescaler
TIM5_ICPSC_DIV2: capture is done once every 2 events
TIM5_ICPSC_DIV4: capture is done once every 4 events
TIM5_ICPSC_DIV8: capture is done once every 8 events

Return values:

None

Definition at line 936 of file stm8s_tim5.c.

References assert_param, IS_TIM5_IC_PRESCALER_OK, and TIM5_CCMR_ICxPSC.

Referenced by TIM5_ICInit(), and TIM5_PWMIConfig().

void TIM5_SetIC3Prescaler ( TIM5_ICPSC_TypeDef TIM5_IC3Prescaler )

Sets the TIM5 Input Capture 3 prescaler.

Parameters:

TIM5_IC3Prescaler

specifies the Input Capture prescaler new value This parameter can be one of the following values:

TIM5_ICPSC_DIV1: no prescaler
TIM5_ICPSC_DIV2: capture is done once every 2 events
TIM5_ICPSC_DIV4: capture is done once every 4 events
TIM5_ICPSC_DIV8: capture is done once every 8 events

Return values:

None

Definition at line 956 of file stm8s_tim5.c.

References assert_param, IS_TIM5_IC_PRESCALER_OK, and TIM5_CCMR_ICxPSC.

Referenced by TIM5_ICInit().

void TIM5_TimeBaseInit	(	TIM5_Prescaler_TypeDef	TIM5_Prescaler,
		uint16_t	TIM5_Period
	)

Initializes the TIM5 Time Base Unit according to the specified parameters.

Parameters:

TIM5_Prescaler	specifies the Prescaler from TIM5_Prescaler_TypeDef.
TIM5_Period	specifies the Period value.

Return values:

None

Definition at line 90 of file stm8s_tim5.c.

Referenced by TIM5_Config().

void TIM5_UpdateDisableConfig ( FunctionalState NewState )

Enables or Disables the TIM5 Update event.

Parameters:

NewState new state of the TIM5 peripheral Preload register.This parameter can be ENABLE or DISABLE.

Return values:

None

Definition at line 387 of file stm8s_tim5.c.

References assert_param, DISABLE, IS_FUNCTIONALSTATE_OK, and TIM5_CR1_UDIS.

void TIM5_UpdateRequestConfig ( TIM5_UpdateSource_TypeDef TIM5_UpdateSource )

Selects the TIM5 Update Request Interrupt source.

Parameters:

TIM5_UpdateSource

specifies the Update source. This parameter can be one of the following values

TIM5_UPDATESOURCE_REGULAR
TIM5_UPDATESOURCE_GLOBAL

Return values:

None

Definition at line 411 of file stm8s_tim5.c.

References assert_param, IS_TIM5_UPDATE_SOURCE_OK, TIM5_CR1_URS, and TIM5_UPDATESOURCE_GLOBAL.

STM8S/A Standard Peripherals Firmware Library: TIM5_Public_Functions

STM8S/A

Functions

Function Documentation

Get in touch