Functions
void	ADC1_AWDChannelConfig (ADC1_Channel_TypeDef Channel, FunctionalState NewState)
	Enables or disables the analog watchdog for the given channel.
void	ADC1_ClearFlag (ADC1_Flag_TypeDef Flag)
	Clear the specified ADC1 Flag.
void	ADC1_ClearITPendingBit (ADC1_IT_TypeDef ITPendingBit)
	Clear the ADC1 End of Conversion pending bit.
void	ADC1_Cmd (FunctionalState NewState)
	Enables or Disables the ADC1 peripheral.
void	ADC1_ConversionConfig (ADC1_ConvMode_TypeDef ADC1_ConversionMode, ADC1_Channel_TypeDef ADC1_Channel, ADC1_Align_TypeDef ADC1_Align)
	Configure the ADC1 conversion on selected channel.
void	ADC1_DataBufferCmd (FunctionalState NewState)
	Enables or Disables the ADC1 data store into the Data Buffer registers rather than in the Data Register.
void	ADC1_DeInit (void)
	Deinitializes the ADC1 peripheral registers to their default reset values.
void	ADC1_ExternalTriggerConfig (ADC1_ExtTrig_TypeDef ADC1_ExtTrigger, FunctionalState NewState)
	Configure the ADC1 conversion on external trigger event.
FlagStatus	ADC1_GetAWDChannelStatus (ADC1_Channel_TypeDef Channel)
	Checks the specified analog watchdog channel status.
uint16_t	ADC1_GetBufferValue (uint8_t Buffer)
	Get one sample of measured signal.
uint16_t	ADC1_GetConversionValue (void)
	Get one sample of measured signal.
FlagStatus	ADC1_GetFlagStatus (ADC1_Flag_TypeDef Flag)
	Checks the specified ADC1 flag status.
ITStatus	ADC1_GetITStatus (ADC1_IT_TypeDef ITPendingBit)
	Returns the specified pending bit status.
void	ADC1_Init (ADC1_ConvMode_TypeDef ADC1_ConversionMode, ADC1_Channel_TypeDef ADC1_Channel, ADC1_PresSel_TypeDef ADC1_PrescalerSelection, ADC1_ExtTrig_TypeDef ADC1_ExtTrigger, FunctionalState ADC1_ExtTriggerState, ADC1_Align_TypeDef ADC1_Align, ADC1_SchmittTrigg_TypeDef ADC1_SchmittTriggerChannel, FunctionalState ADC1_SchmittTriggerState)
	Initializes the ADC1 peripheral according to the specified parameters.
void	ADC1_ITConfig (ADC1_IT_TypeDef ADC1_IT, FunctionalState NewState)
	Enables or disables the ADC1 interrupt.
void	ADC1_PrescalerConfig (ADC1_PresSel_TypeDef ADC1_Prescaler)
	Configure the ADC1 prescaler division factor.
void	ADC1_ScanModeCmd (FunctionalState NewState)
	Enables or Disables the ADC1 scan mode.
void	ADC1_SchmittTriggerConfig (ADC1_SchmittTrigg_TypeDef ADC1_SchmittTriggerChannel, FunctionalState NewState)
	Enables or disables the ADC1 Schmitt Trigger on a selected channel.
void	ADC1_SetHighThreshold (uint16_t Threshold)
	Sets the high threshold of the analog watchdog.
void	ADC1_SetLowThreshold (uint16_t Threshold)
	Sets the low threshold of the analog watchdog.
void	ADC1_StartConversion (void)
	Start ADC1 conversion.

Function Documentation

void ADC1_AWDChannelConfig	(	ADC1_Channel_TypeDef	Channel,
		FunctionalState	NewState
	)

Enables or disables the analog watchdog for the given channel.

Parameters:

Channel	specifies the desired Channel. It can be set of the values of ADC1_Channel_TypeDef.
NewState	specifies the analog watchdog new state. can have one of the values of FunctionalState.

Return values:

None

Definition at line 405 of file stm8s_adc1.c.

References DISABLE, IS_ADC1_CHANNEL_OK, and IS_FUNCTIONALSTATE_OK.

void ADC1_ClearFlag ( ADC1_Flag_TypeDef Flag )

Clear the specified ADC1 Flag.

Parameters:

Flag,: ADC1 flag. can be one of the values of ADC1_Flag_TypeDef.

Return values:

None

Definition at line 567 of file stm8s_adc1.c.

References IS_ADC1_FLAG_OK.

void ADC1_ClearITPendingBit ( ADC1_IT_TypeDef ITPendingBit )

Clear the ADC1 End of Conversion pending bit.

Parameters:

ITPendingBit

: the IT pending bit to clear. This parameter can be one of the following values:

ADC1_IT_AWD : Analog WDG IT status
ADC1_IT_AWS0 : Analog channel 0 IT status
ADC1_IT_AWS1 : Analog channel 1 IT status
ADC1_IT_AWS2 : Analog channel 2 IT status
ADC1_IT_AWS3 : Analog channel 3 IT status
ADC1_IT_AWS4 : Analog channel 4 IT status
ADC1_IT_AWS5 : Analog channel 5 IT status
ADC1_IT_AWS6 : Analog channel 6 IT status
ADC1_IT_AWS7 : Analog channel 7 IT status
ADC1_IT_AWS8 : Analog channel 8 IT status
ADC1_IT_AWS9 : Analog channel 9 IT status
ADC1_IT_EOC : EOC pending bit

Return values:

None

Definition at line 662 of file stm8s_adc1.c.

References IS_ADC1_ITPENDINGBIT_OK.

void ADC1_Cmd ( FunctionalState NewState )

Enables or Disables the ADC1 peripheral.

Parameters:

NewState,: specifies the peripheral enabled or disabled state.

Return values:

None

Definition at line 126 of file stm8s_adc1.c.

References DISABLE, and IS_FUNCTIONALSTATE_OK.

void ADC1_ConversionConfig	(	ADC1_ConvMode_TypeDef	ADC1_ConversionMode,
		ADC1_Channel_TypeDef	ADC1_Channel,
		ADC1_Align_TypeDef	ADC1_Align
	)

Configure the ADC1 conversion on selected channel.

Parameters:

ADC1_ConversionMode	Specifies the conversion type. It can be set of the values of ADC1_ConvMode_TypeDef
ADC1_Channel	specifies the ADC1 Channel. It can be set of the values of ADC1_Channel_TypeDef
ADC1_Align	specifies the converted data alignment. It can be set of the values of ADC1_Align_TypeDef

Return values:

None

Definition at line 286 of file stm8s_adc1.c.

References ADC1_CONVERSIONMODE_CONTINUOUS, IS_ADC1_ALIGN_OK, IS_ADC1_CHANNEL_OK, and IS_ADC1_CONVERSIONMODE_OK.

Referenced by ADC1_Init().

void ADC1_DataBufferCmd ( FunctionalState NewState )

Enables or Disables the ADC1 data store into the Data Buffer registers rather than in the Data Register.

Parameters:

NewState,: specifies the selected mode enabled or disabled state.

Return values:

None

Definition at line 166 of file stm8s_adc1.c.

References DISABLE, and IS_FUNCTIONALSTATE_OK.

void ADC1_DeInit ( void )

Deinitializes the ADC1 peripheral registers to their default reset values.

Parameters:

None

Return values:

None

Definition at line 52 of file stm8s_adc1.c.

void ADC1_ExternalTriggerConfig	(	ADC1_ExtTrig_TypeDef	ADC1_ExtTrigger,
		FunctionalState	NewState
	)

Configure the ADC1 conversion on external trigger event.

Full description:: The selected external trigger event can be enabled or disabled.

Parameters:

ADC1_ExtTrigger	to select the External trigger event. can have one of the values of ADC1_ExtTrig_TypeDef.
NewState	to enable/disable the selected external trigger can have one of the values of FunctionalState.

Return values:

None

Definition at line 325 of file stm8s_adc1.c.

References DISABLE, IS_ADC1_EXTTRIG_OK, and IS_FUNCTIONALSTATE_OK.

Referenced by ADC1_Init().

FlagStatus ADC1_GetAWDChannelStatus ( ADC1_Channel_TypeDef Channel )

Checks the specified analog watchdog channel status.

Parameters:

Channel,: specify the channel of which to check the analog watchdog can be one of the values of ADC1_Channel_TypeDef.

Return values:

FlagStatus Status of the analog watchdog.

Definition at line 502 of file stm8s_adc1.c.

References IS_ADC1_CHANNEL_OK.

uint16_t ADC1_GetBufferValue ( uint8_t Buffer )

Get one sample of measured signal.

Parameters:

Buffer specifies the buffer to read.

Return values:

BufferValue,: value read from the given buffer.

Required preconditions:: ADC1 conversion finished.

Definition at line 466 of file stm8s_adc1.c.

References ADC1_BaseAddress, and IS_ADC1_BUFFER_OK.

uint16_t ADC1_GetConversionValue ( void )

Get one sample of measured signal.

Parameters:

None

Return values:

ConversionValue,: value of the measured signal.

Required preconditions:: ADC1 conversion finished.

Definition at line 370 of file stm8s_adc1.c.

FlagStatus ADC1_GetFlagStatus ( ADC1_Flag_TypeDef Flag )

Checks the specified ADC1 flag status.

Parameters:

Flag,: ADC1 flag. can be one of the values of ADC1_Flag_TypeDef.

Return values:

FlagStatus Status of the ADC1 flag.

Definition at line 527 of file stm8s_adc1.c.

References IS_ADC1_FLAG_OK.

ITStatus ADC1_GetITStatus ( ADC1_IT_TypeDef ITPendingBit )

Returns the specified pending bit status.

Parameters:

ITPendingBit

: the IT pending bit to check. This parameter can be one of the following values:

ADC1_IT_AWD : Analog WDG IT status
ADC1_IT_AWS0 : Analog channel 0 IT status
ADC1_IT_AWS1 : Analog channel 1 IT status
ADC1_IT_AWS2 : Analog channel 2 IT status
ADC1_IT_AWS3 : Analog channel 3 IT status
ADC1_IT_AWS4 : Analog channel 4 IT status
ADC1_IT_AWS5 : Analog channel 5 IT status
ADC1_IT_AWS6 : Analog channel 6 IT status
ADC1_IT_AWS7 : Analog channel 7 IT status
ADC1_IT_AWS8 : Analog channel 8 IT status
ADC1_IT_AWS9 : Analog channel 9 IT status
ADC1_IT_EOC : EOC pending bit

Return values:

ITStatus,: status of the specified pending bit.

Definition at line 616 of file stm8s_adc1.c.

References IS_ADC1_ITPENDINGBIT_OK, and RESET.

void ADC1_Init	(	ADC1_ConvMode_TypeDef	ADC1_ConversionMode,
		ADC1_Channel_TypeDef	ADC1_Channel,
		ADC1_PresSel_TypeDef	ADC1_PrescalerSelection,
		ADC1_ExtTrig_TypeDef	ADC1_ExtTrigger,
		FunctionalState	ADC1_ExtTriggerState,
		ADC1_Align_TypeDef	ADC1_Align,
		ADC1_SchmittTrigg_TypeDef	ADC1_SchmittTriggerChannel,
		FunctionalState	ADC1_SchmittTriggerState
	)

Initializes the ADC1 peripheral according to the specified parameters.

Parameters:

ADC1_ConversionMode,:	specifies the conversion mode can be one of the values of ADC1_ConvMode_TypeDef.
ADC1_Channel,:	specifies the channel to convert can be one of the values of ADC1_Channel_TypeDef.
ADC1_PrescalerSelection,:	specifies the ADC1 prescaler can be one of the values of ADC1_PresSel_TypeDef.
ADC1_ExtTrigger,:	specifies the external trigger can be one of the values of ADC1_ExtTrig_TypeDef.
ADC1_ExtTriggerState,:	specifies the external trigger new state can be one of the values of FunctionalState.
ADC1_Align,:	specifies the converted data alignment can be one of the values of ADC1_Align_TypeDef.
ADC1_SchmittTriggerChannel,:	specifies the schmitt trigger channel can be one of the values of ADC1_SchmittTrigg_TypeDef.
ADC1_SchmittTriggerState,:	specifies the schmitt trigger state can be one of the values of FunctionalState.

Return values:

None

Definition at line 88 of file stm8s_adc1.c.

References ADC1_ConversionConfig(), ADC1_ExternalTriggerConfig(), ADC1_PrescalerConfig(), ADC1_SchmittTriggerConfig(), IS_ADC1_ALIGN_OK, IS_ADC1_CHANNEL_OK, IS_ADC1_CONVERSIONMODE_OK, IS_ADC1_EXTTRIG_OK, IS_ADC1_PRESSEL_OK, IS_ADC1_SCHMITTTRIG_OK, and IS_FUNCTIONALSTATE_OK.

void ADC1_ITConfig	(	ADC1_IT_TypeDef	ADC1_IT,
		FunctionalState	NewState
	)

Enables or disables the ADC1 interrupt.

Parameters:

ADC1_IT	specifies the name of the interrupt to enable or disable. This parameter can be one of the following values: ADC1_IT_AWDITEN : Analog WDG interrupt enable ADC1_IT_EOCITEN : EOC iterrupt enable
NewState	specifies the state of the interrupt to apply.

Return values:

None

Definition at line 190 of file stm8s_adc1.c.

References DISABLE, IS_ADC1_IT_OK, and IS_FUNCTIONALSTATE_OK.

void ADC1_PrescalerConfig ( ADC1_PresSel_TypeDef ADC1_Prescaler )

Configure the ADC1 prescaler division factor.

Parameters:

ADC1_Prescaler,: the selected precaler. It can be one of the values of ADC1_PresSel_TypeDef.

Return values:

None

Definition at line 214 of file stm8s_adc1.c.

References IS_ADC1_PRESSEL_OK.

Referenced by ADC1_Init().

void ADC1_ScanModeCmd ( FunctionalState NewState )

Enables or Disables the ADC1 scan mode.

Parameters:

NewState,: specifies the selected mode enabled or disabled state.

Return values:

None

Definition at line 146 of file stm8s_adc1.c.

References DISABLE, and IS_FUNCTIONALSTATE_OK.

void ADC1_SchmittTriggerConfig	(	ADC1_SchmittTrigg_TypeDef	ADC1_SchmittTriggerChannel,
		FunctionalState	NewState
	)

Enables or disables the ADC1 Schmitt Trigger on a selected channel.

Parameters:

ADC1_SchmittTriggerChannel	specifies the desired Channel. It can be set of the values of ADC1_SchmittTrigg_TypeDef.
NewState	specifies Channel new status. can have one of the values of FunctionalState.

Return values:

None

Definition at line 233 of file stm8s_adc1.c.

References ADC1_SCHMITTTRIG_ALL, ADC1_SCHMITTTRIG_CHANNEL8, DISABLE, IS_ADC1_SCHMITTTRIG_OK, and IS_FUNCTIONALSTATE_OK.

Referenced by ADC1_Init().

void ADC1_SetHighThreshold ( uint16_t Threshold )

Sets the high threshold of the analog watchdog.

Parameters:

Threshold specifies the high threshold value. this value depends on the reference voltage range.

Return values:

None

Definition at line 441 of file stm8s_adc1.c.

void ADC1_SetLowThreshold ( uint16_t Threshold )

Sets the low threshold of the analog watchdog.

Parameters:

Threshold specifies the low threshold value. this value depends on the reference voltage range.

Return values:

None

Definition at line 453 of file stm8s_adc1.c.

void ADC1_StartConversion ( void )

Start ADC1 conversion.

Full description:: This function triggers the start of conversion, after ADC1 configuration.

Parameters:

None

Return values:

None

Required preconditions:: Enable the ADC1 peripheral before calling this function

Definition at line 358 of file stm8s_adc1.c.

STM8S/A Standard Peripherals Drivers: ADC1_Public_Functions

STM8S/A

Functions

Function Documentation

Get in touch