TIM1_Public_Functions

Functions
static void	TI1_Config (uint8_t TIM1_ICPolarity, uint8_t TIM1_ICSelection, uint8_t TIM1_ICFilter)
	Configure the TI1 as Input.
static void	TI2_Config (uint8_t TIM1_ICPolarity, uint8_t TIM1_ICSelection, uint8_t TIM1_ICFilter)
	Configure the TI2 as Input.
static void	TI3_Config (uint8_t TIM1_ICPolarity, uint8_t TIM1_ICSelection, uint8_t TIM1_ICFilter)
	Configure the TI3 as Input.
static void	TI4_Config (uint8_t TIM1_ICPolarity, uint8_t TIM1_ICSelection, uint8_t TIM1_ICFilter)
	Configure the TI4 as Input.
void	TIM1_ARRPreloadConfig (FunctionalState NewState)
	Enables or disables TIM1 peripheral Preload register on ARR.
void	TIM1_BDTRConfig (TIM1_OSSIState_TypeDef TIM1_OSSIState, TIM1_LockLevel_TypeDef TIM1_LockLevel, uint8_t TIM1_DeadTime, TIM1_BreakState_TypeDef TIM1_Break, TIM1_BreakPolarity_TypeDef TIM1_BreakPolarity, TIM1_AutomaticOutput_TypeDef TIM1_AutomaticOutput)
	Configures the Break feature, dead time, Lock level, the OSSI, and the AOE(automatic output enable).
void	TIM1_CCPreloadControl (FunctionalState NewState)
	Sets or Resets the TIM1 peripheral Capture Compare Preload Control bit.
void	TIM1_CCxCmd (TIM1_Channel_TypeDef TIM1_Channel, FunctionalState NewState)
	Enables or disables the TIM1 Capture Compare Channel x (x=1,..,4).
void	TIM1_CCxNCmd (TIM1_Channel_TypeDef TIM1_Channel, FunctionalState NewState)
	Enables or disables the TIM1 Capture Compare Channel xN (xN=1,..,3).
void	TIM1_ClearFlag (TIM1_FLAG_TypeDef TIM1_FLAG)
	Clears the TIM1�s pending flags.
void	TIM1_ClearITPendingBit (TIM1_IT_TypeDef TIM1_IT)
	Clears the TIM1's interrupt pending bits.
void	TIM1_Cmd (FunctionalState NewState)
	Enables or disables the TIM1 peripheral.
void	TIM1_CounterModeConfig (TIM1_CounterMode_TypeDef TIM1_CounterMode)
	Specifies the TIM1 Counter Mode to be used.
void	TIM1_CtrlPWMOutputs (FunctionalState NewState)
	Enables or disables the TIM1 peripheral Main Outputs.
void	TIM1_DeInit (void)
	Deinitializes the TIM1 peripheral registers to their default reset values.
void	TIM1_EncoderInterfaceConfig (TIM1_EncoderMode_TypeDef TIM1_EncoderMode, TIM1_ICPolarity_TypeDef TIM1_IC1Polarity, TIM1_ICPolarity_TypeDef TIM1_IC2Polarity)
	Configures the TIM1 Encoder Interface.
void	TIM1_ETRClockMode1Config (TIM1_ExtTRGPSC_TypeDef TIM1_ExtTRGPrescaler, TIM1_ExtTRGPolarity_TypeDef TIM1_ExtTRGPolarity, uint8_t ExtTRGFilter)
	Configures the TIM1 External clock Mode1.
void	TIM1_ETRClockMode2Config (TIM1_ExtTRGPSC_TypeDef TIM1_ExtTRGPrescaler, TIM1_ExtTRGPolarity_TypeDef TIM1_ExtTRGPolarity, uint8_t ExtTRGFilter)
	Configures the TIM1 External clock Mode2.
void	TIM1_ETRConfig (TIM1_ExtTRGPSC_TypeDef TIM1_ExtTRGPrescaler, TIM1_ExtTRGPolarity_TypeDef TIM1_ExtTRGPolarity, uint8_t ExtTRGFilter)
	Configures the TIM1 External Trigger.
void	TIM1_ForcedOC1Config (TIM1_ForcedAction_TypeDef TIM1_ForcedAction)
	Forces the TIM1 Channel1 output waveform to active or inactive level.
void	TIM1_ForcedOC2Config (TIM1_ForcedAction_TypeDef TIM1_ForcedAction)
	Forces the TIM1 Channel2 output waveform to active or inactive level.
void	TIM1_ForcedOC3Config (TIM1_ForcedAction_TypeDef TIM1_ForcedAction)
	Forces the TIM1 Channel3 output waveform to active or inactive level.
void	TIM1_ForcedOC4Config (TIM1_ForcedAction_TypeDef TIM1_ForcedAction)
	Forces the TIM1 Channel4 output waveform to active or inactive level.
void	TIM1_GenerateEvent (TIM1_EventSource_TypeDef TIM1_EventSource)
	Configures the TIM1 event to be generated by software.
uint16_t	TIM1_GetCapture1 (void)
	Gets the TIM1 Input Capture 1 value.
uint16_t	TIM1_GetCapture2 (void)
	Gets the TIM1 Input Capture 2 value.
uint16_t	TIM1_GetCapture3 (void)
	Gets the TIM1 Input Capture 3 value.
uint16_t	TIM1_GetCapture4 (void)
	Gets the TIM1 Input Capture 4 value.
uint16_t	TIM1_GetCounter (void)
	Gets the TIM1 Counter value.
FlagStatus	TIM1_GetFlagStatus (TIM1_FLAG_TypeDef TIM1_FLAG)
	Checks whether the specified TIM1 flag is set or not.
ITStatus	TIM1_GetITStatus (TIM1_IT_TypeDef TIM1_IT)
	Checks whether the TIM1 interrupt has occurred or not.
uint16_t	TIM1_GetPrescaler (void)
	Gets the TIM1 Prescaler value.
void	TIM1_ICInit (TIM1_Channel_TypeDef TIM1_Channel, TIM1_ICPolarity_TypeDef TIM1_ICPolarity, TIM1_ICSelection_TypeDef TIM1_ICSelection, TIM1_ICPSC_TypeDef TIM1_ICPrescaler, uint8_t TIM1_ICFilter)
	Initializes the TIM1 peripheral according to the specified parameters.
void	TIM1_InternalClockConfig (void)
	Configures the TIM1 internal Clock.
void	TIM1_ITConfig (TIM1_IT_TypeDef TIM1_IT, FunctionalState NewState)
	Enables or disables the specified TIM1 interrupts.
void	TIM1_OC1FastConfig (FunctionalState NewState)
	Configures the TIM1 Capture Compare 1 Fast feature.
void	TIM1_OC1Init (TIM1_OCMode_TypeDef TIM1_OCMode, TIM1_OutputState_TypeDef TIM1_OutputState, TIM1_OutputNState_TypeDef TIM1_OutputNState, uint16_t TIM1_Pulse, TIM1_OCPolarity_TypeDef TIM1_OCPolarity, TIM1_OCNPolarity_TypeDef TIM1_OCNPolarity, TIM1_OCIdleState_TypeDef TIM1_OCIdleState, TIM1_OCNIdleState_TypeDef TIM1_OCNIdleState)
	Initializes the TIM1 Channel1 according to the specified parameters.
void	TIM1_OC1NPolarityConfig (TIM1_OCNPolarity_TypeDef TIM1_OCNPolarity)
	Configures the TIM1 Channel 1N polarity.
void	TIM1_OC1PolarityConfig (TIM1_OCPolarity_TypeDef TIM1_OCPolarity)
	Configures the TIM1 Channel 1 polarity.
void	TIM1_OC1PreloadConfig (FunctionalState NewState)
	Enables or disables the TIM1 peripheral Preload Register on CCR1.
void	TIM1_OC2FastConfig (FunctionalState NewState)
	Configures the TIM1 Capture Compare 2 Fast feature.
void	TIM1_OC2Init (TIM1_OCMode_TypeDef TIM1_OCMode, TIM1_OutputState_TypeDef TIM1_OutputState, TIM1_OutputNState_TypeDef TIM1_OutputNState, uint16_t TIM1_Pulse, TIM1_OCPolarity_TypeDef TIM1_OCPolarity, TIM1_OCNPolarity_TypeDef TIM1_OCNPolarity, TIM1_OCIdleState_TypeDef TIM1_OCIdleState, TIM1_OCNIdleState_TypeDef TIM1_OCNIdleState)
	Initializes the TIM1 Channel2 according to the specified parameters.
void	TIM1_OC2NPolarityConfig (TIM1_OCNPolarity_TypeDef TIM1_OCNPolarity)
	Configures the TIM1 Channel 2N polarity.
void	TIM1_OC2PolarityConfig (TIM1_OCPolarity_TypeDef TIM1_OCPolarity)
	Configures the TIM1 Channel 2 polarity.
void	TIM1_OC2PreloadConfig (FunctionalState NewState)
	Enables or disables the TIM1 peripheral Preload Register on CCR2.
void	TIM1_OC3FastConfig (FunctionalState NewState)
	Configures the TIM1 Capture Compare 3 Fast feature.
void	TIM1_OC3Init (TIM1_OCMode_TypeDef TIM1_OCMode, TIM1_OutputState_TypeDef TIM1_OutputState, TIM1_OutputNState_TypeDef TIM1_OutputNState, uint16_t TIM1_Pulse, TIM1_OCPolarity_TypeDef TIM1_OCPolarity, TIM1_OCNPolarity_TypeDef TIM1_OCNPolarity, TIM1_OCIdleState_TypeDef TIM1_OCIdleState, TIM1_OCNIdleState_TypeDef TIM1_OCNIdleState)
	Initializes the TIM1 Channel3 according to the specified parameters.
void	TIM1_OC3NPolarityConfig (TIM1_OCNPolarity_TypeDef TIM1_OCNPolarity)
	Configures the TIM1 Channel 3N polarity.
void	TIM1_OC3PolarityConfig (TIM1_OCPolarity_TypeDef TIM1_OCPolarity)
	Configures the TIM1 Channel 3 polarity.
void	TIM1_OC3PreloadConfig (FunctionalState NewState)
	Enables or disables the TIM1 peripheral Preload Register on CCR3.
void	TIM1_OC4FastConfig (FunctionalState NewState)
	Configures the TIM1 Capture Compare 4 Fast feature.
void	TIM1_OC4Init (TIM1_OCMode_TypeDef TIM1_OCMode, TIM1_OutputState_TypeDef TIM1_OutputState, uint16_t TIM1_Pulse, TIM1_OCPolarity_TypeDef TIM1_OCPolarity, TIM1_OCIdleState_TypeDef TIM1_OCIdleState)
	Initializes the TIM1 Channel4 according to the specified parameters.
void	TIM1_OC4PolarityConfig (TIM1_OCPolarity_TypeDef TIM1_OCPolarity)
	Configures the TIM1 Channel 4 polarity.
void	TIM1_OC4PreloadConfig (FunctionalState NewState)
	Enables or disables the TIM1 peripheral Preload Register on CCR4.
void	TIM1_PrescalerConfig (uint16_t Prescaler, TIM1_PSCReloadMode_TypeDef TIM1_PSCReloadMode)
	Configures the TIM1 Prescaler.
void	TIM1_PWMIConfig (TIM1_Channel_TypeDef TIM1_Channel, TIM1_ICPolarity_TypeDef TIM1_ICPolarity, TIM1_ICSelection_TypeDef TIM1_ICSelection, TIM1_ICPSC_TypeDef TIM1_ICPrescaler, uint8_t TIM1_ICFilter)
	Configures the TIM1 peripheral in PWM Input Mode according to the specified parameters.
void	TIM1_SelectCOM (FunctionalState NewState)
	Selects the TIM1 peripheral Commutation event.
void	TIM1_SelectHallSensor (FunctionalState NewState)
	Enables or Disables the TIM1�s Hall sensor interface.
void	TIM1_SelectInputTrigger (TIM1_TS_TypeDef TIM1_InputTriggerSource)
	Selects the TIM1 Input Trigger source.
void	TIM1_SelectMasterSlaveMode (FunctionalState NewState)
	Sets or Resets the TIM1 Master/Slave Mode.
void	TIM1_SelectOCxM (TIM1_Channel_TypeDef TIM1_Channel, TIM1_OCMode_TypeDef TIM1_OCMode)
	Selects the TIM1 Output Compare Mode.
void	TIM1_SelectOnePulseMode (TIM1_OPMode_TypeDef TIM1_OPMode)
	Selects the TIM1�s One Pulse Mode.
void	TIM1_SelectOutputTrigger (TIM1_TRGOSource_TypeDef TIM1_TRGOSource)
	Selects the TIM1 Trigger Output Mode.
void	TIM1_SelectSlaveMode (TIM1_SlaveMode_TypeDef TIM1_SlaveMode)
	Selects the TIM1 Slave Mode.
void	TIM1_SetAutoreload (uint16_t Autoreload)
	Sets the TIM1 Autoreload Register value.
void	TIM1_SetCompare1 (uint16_t Compare1)
	Sets the TIM1 Capture Compare1 Register value.
void	TIM1_SetCompare2 (uint16_t Compare2)
	Sets the TIM1 Capture Compare2 Register value.
void	TIM1_SetCompare3 (uint16_t Compare3)
	Sets the TIM1 Capture Compare3 Register value.
void	TIM1_SetCompare4 (uint16_t Compare4)
	Sets the TIM1 Capture Compare4 Register value.
void	TIM1_SetCounter (uint16_t Counter)
	Sets the TIM1 Counter Register value.
void	TIM1_SetIC1Prescaler (TIM1_ICPSC_TypeDef TIM1_IC1Prescaler)
	Sets the TIM1 Input Capture 1 prescaler.
void	TIM1_SetIC2Prescaler (TIM1_ICPSC_TypeDef TIM1_IC2Prescaler)
	Sets the TIM1 Input Capture 2 prescaler.
void	TIM1_SetIC3Prescaler (TIM1_ICPSC_TypeDef TIM1_IC3Prescaler)
	Sets the TIM1 Input Capture 3 prescaler.
void	TIM1_SetIC4Prescaler (TIM1_ICPSC_TypeDef TIM1_IC4Prescaler)
	Sets the TIM1 Input Capture 4 prescaler.
void	TIM1_TimeBaseInit (uint16_t TIM1_Prescaler, TIM1_CounterMode_TypeDef TIM1_CounterMode, uint16_t TIM1_Period, uint8_t TIM1_RepetitionCounter)
	Initializes the TIM1 Time Base Unit according to the specified parameters.
void	TIM1_TIxExternalClockConfig (TIM1_TIxExternalCLK1Source_TypeDef TIM1_TIxExternalCLKSource, TIM1_ICPolarity_TypeDef TIM1_ICPolarity, uint8_t ICFilter)
	Configures the TIM1 Trigger as External Clock.
void	TIM1_UpdateDisableConfig (FunctionalState NewState)
	Enables or Disables the TIM1 Update event.
void	TIM1_UpdateRequestConfig (TIM1_UpdateSource_TypeDef TIM1_UpdateSource)
	Selects the TIM1 Update Request Interrupt source.

---

Function Documentation

static void TI1_Config	(	uint8_t	TIM1_ICPolarity,
		uint8_t	TIM1_ICSelection,
		uint8_t	TIM1_ICFilter
	)		[static]

Configure the TI1 as Input.

Parameters:

TIM1_ICPolarity	The Input Polarity. This parameter can be one of the following values: TIM1_ICPOLARITY_FALLING TIM1_ICPOLARITY_RISING
TIM1_ICSelection	specifies the input to be used. This parameter can be one of the following values: TIM1_ICSELECTION_DIRECTTI: TIM1 Input 1 is selected to be connected to IC1. TIM1_ICSELECTION_INDIRECTTI: TIM1 Input 1 is selected to be connected to IC2.
TIM1_ICFilter	Specifies the Input Capture Filter. This parameter must be a value between 0x00 and 0x0F.

Return values:

None

Definition at line 2174 of file stm8s_tim1.c.

References TIM1, TIM1_CCER1_CC1E, TIM1_CCER1_CC1P, TIM1_CCMR_CCxS, TIM1_CCMR_ICxF, and TIM1_ICPOLARITY_RISING.

Referenced by TIM1_ICInit(), TIM1_PWMIConfig(), and TIM1_TIxExternalClockConfig().

static void TI2_Config	(	uint8_t	TIM1_ICPolarity,
		uint8_t	TIM1_ICSelection,
		uint8_t	TIM1_ICFilter
	)		[static]

Configure the TI2 as Input.

Parameters:

TIM1_ICPolarity	The Input Polarity. This parameter can be one of the following values: TIM1_ICPOLARITY_FALLING TIM1_ICPOLARITY_RISING
TIM1_ICSelection	specifies the input to be used. This parameter can be one of the following values: TIM1_ICSELECTION_DIRECTTI: TIM1 Input 2 is selected to be connected to IC2. TIM1_ICSELECTION_INDIRECTTI: TIM1 Input 2 is selected to be connected to IC1.
TIM1_ICFilter	Specifies the Input Capture Filter. This parameter must be a value between 0x00 and 0x0F.

Return values:

None

Definition at line 2215 of file stm8s_tim1.c.

References TIM1, TIM1_CCER1_CC2E, TIM1_CCER1_CC2P, TIM1_CCMR_CCxS, TIM1_CCMR_ICxF, and TIM1_ICPOLARITY_RISING.

Referenced by TIM1_ICInit(), TIM1_PWMIConfig(), and TIM1_TIxExternalClockConfig().

static void TI3_Config	(	uint8_t	TIM1_ICPolarity,
		uint8_t	TIM1_ICSelection,
		uint8_t	TIM1_ICFilter
	)		[static]

Configure the TI3 as Input.

Parameters:

TIM1_ICPolarity	The Input Polarity. This parameter can be one of the following values: TIM1_ICPOLARITY_FALLING TIM1_ICPOLARITY_RISING
TIM1_ICSelection	specifies the input to be used. This parameter can be one of the following values: TIM1_ICSELECTION_DIRECTTI: TIM1 Input 3 is selected to be connected to IC3. TIM1_ICSELECTION_INDIRECTTI: TIM1 Input 3 is selected to be connected to IC4.
TIM1_ICFilter	Specifies the Input Capture Filter. This parameter must be a value between 0x00 and 0x0F.

Return values:

None

Definition at line 2254 of file stm8s_tim1.c.

References TIM1, TIM1_CCER2_CC3E, TIM1_CCER2_CC3P, TIM1_CCMR_CCxS, TIM1_CCMR_ICxF, and TIM1_ICPOLARITY_RISING.

Referenced by TIM1_ICInit().

static void TI4_Config	(	uint8_t	TIM1_ICPolarity,
		uint8_t	TIM1_ICSelection,
		uint8_t	TIM1_ICFilter
	)		[static]

Configure the TI4 as Input.

Parameters:

TIM1_ICPolarity	The Input Polarity. This parameter can be one of the following values: TIM1_ICPOLARITY_FALLING TIM1_ICPOLARITY_RISING
TIM1_ICSelection	specifies the input to be used. This parameter can be one of the following values: TIM1_ICSELECTION_DIRECTTI: TIM1 Input 4 is selected to be connected to IC4. TIM1_ICSELECTION_INDIRECTTI: TIM1 Input 4 is selected to be connected to IC3.
TIM1_ICFilter	Specifies the Input Capture Filter. This parameter must be a value between 0x00 and 0x0F.

Return values:

None

Definition at line 2294 of file stm8s_tim1.c.

References TIM1, TIM1_CCER2_CC4E, TIM1_CCER2_CC4P, TIM1_CCMR_CCxS, TIM1_CCMR_ICxF, and TIM1_ICPOLARITY_RISING.

Referenced by TIM1_ICInit().

void TIM1_ARRPreloadConfig

(

FunctionalState

NewState

)

Enables or disables TIM1 peripheral Preload register on ARR.

Parameters:

NewState

new state of the TIM1 peripheral Preload register. This parameter can be ENABLE or DISABLE.

Return values:

None

Definition at line 1139 of file stm8s_tim1.c.

References DISABLE, IS_FUNCTIONALSTATE_OK, TIM1, and TIM1_CR1_ARPE.

void TIM1_BDTRConfig	(	TIM1_OSSIState_TypeDef	TIM1_OSSIState,
		TIM1_LockLevel_TypeDef	TIM1_LockLevel,
		uint8_t	TIM1_DeadTime,
		TIM1_BreakState_TypeDef	TIM1_Break,
		TIM1_BreakPolarity_TypeDef	TIM1_BreakPolarity,
		TIM1_AutomaticOutput_TypeDef	TIM1_AutomaticOutput
	)

Configures the Break feature, dead time, Lock level, the OSSI, and the AOE(automatic output enable).

Parameters:

TIM1_OSSIState	specifies the OSSIS State from TIM1_OSSIState_TypeDef.
TIM1_LockLevel	specifies the lock level from TIM1_LockLevel_TypeDef.
TIM1_DeadTime	specifies the dead time value.
TIM1_Break	specifies the Break state TIM1_BreakState_TypeDef.
TIM1_BreakPolarity	specifies the Break polarity from TIM1_BreakPolarity_TypeDef.
TIM1_AutomaticOutput	specifies the Automatic Output configuration from TIM1_AutomaticOutput_TypeDef.

Return values:

None

Definition at line 388 of file stm8s_tim1.c.

References IS_TIM1_AUTOMATIC_OUTPUT_STATE_OK, IS_TIM1_BREAK_POLARITY_OK, IS_TIM1_BREAK_STATE_OK, IS_TIM1_LOCK_LEVEL_OK, IS_TIM1_OSSI_STATE_OK, and TIM1.

void TIM1_CCPreloadControl

(

FunctionalState

NewState

)

Sets or Resets the TIM1 peripheral Capture Compare Preload Control bit.

Parameters:

NewState

new state of the Capture Compare Preload Control bit. This parameter can be ENABLE or DISABLE.

Return values:

None

Definition at line 1183 of file stm8s_tim1.c.

References DISABLE, IS_FUNCTIONALSTATE_OK, TIM1, and TIM1_CR2_CCPC.

void TIM1_CCxCmd	(	TIM1_Channel_TypeDef	TIM1_Channel,
		FunctionalState	NewState
	)

Enables or disables the TIM1 Capture Compare Channel x (x=1,..,4).

Parameters:

TIM1_Channel	specifies the TIM1 Channel. This parameter can be one of the following values: TIM1_CHANNEL_1: TIM1 Channel1 TIM1_CHANNEL_2: TIM1 Channel2 TIM1_CHANNEL_3: TIM1 Channel3 TIM1_CHANNEL_4: TIM1 Channel4
NewState	specifies the TIM1 Channel CCxE bit new state. This parameter can be: ENABLE or DISABLE.

Return values:

None

Definition at line 1579 of file stm8s_tim1.c.

References DISABLE, IS_FUNCTIONALSTATE_OK, IS_TIM1_CHANNEL_OK, TIM1, TIM1_CCER1_CC1E, TIM1_CCER1_CC2E, TIM1_CCER2_CC3E, TIM1_CCER2_CC4E, TIM1_CHANNEL_1, TIM1_CHANNEL_2, and TIM1_CHANNEL_3.

void TIM1_CCxNCmd	(	TIM1_Channel_TypeDef	TIM1_Channel,
		FunctionalState	NewState
	)

Enables or disables the TIM1 Capture Compare Channel xN (xN=1,..,3).

Parameters:

TIM1_Channel	specifies the TIM1 Channel. This parameter can be one of the following values: TIM1_CHANNEL_1: TIM1 Channel1 TIM1_CHANNEL_2: TIM1 Channel2 TIM1_CHANNEL_3: TIM1 Channel3
NewState	specifies the TIM1 Channel CCxNE bit new state. This parameter can be: ENABLE or DISABLE.

Return values:

None

Definition at line 1647 of file stm8s_tim1.c.

References DISABLE, IS_FUNCTIONALSTATE_OK, IS_TIM1_COMPLEMENTARY_CHANNEL_OK, TIM1, TIM1_CCER1_CC1NE, TIM1_CCER1_CC2NE, TIM1_CCER2_CC3NE, TIM1_CHANNEL_1, and TIM1_CHANNEL_2.

void TIM1_ClearFlag

(

TIM1_FLAG_TypeDef

TIM1_FLAG

)

Clears the TIM1�s pending flags.

Parameters:

TIM1_FLAG

specifies the flag to clear. This parameter can be one of the following values: TIM1_FLAG_UPDATE: TIM1 update Flag TIM1_FLAG_CC1: TIM1 Capture Compare 1 Flag TIM1_FLAG_CC2: TIM1 Capture Compare 2 Flag TIM1_FLAG_CC3: TIM1 Capture Compare 3 Flag TIM1_FLAG_CC4: TIM1 Capture Compare 4 Flag TIM1_FLAG_COM: TIM1 Commutation Flag TIM1_FLAG_TRIGGER: TIM1 Trigger Flag TIM1_FLAG_BREAK: TIM1 Break Flag TIM1_FLAG_CC1OF: TIM1 Capture Compare 1 overcapture Flag TIM1_FLAG_CC2OF: TIM1 Capture Compare 2 overcapture Flag TIM1_FLAG_CC3OF: TIM1 Capture Compare 3 overcapture Flag TIM1_FLAG_CC4OF: TIM1 Capture Compare 4 overcapture Flag

Return values:

None.

Definition at line 2087 of file stm8s_tim1.c.

References IS_TIM1_CLEAR_FLAG_OK, and TIM1.

void TIM1_ClearITPendingBit

(

TIM1_IT_TypeDef

TIM1_IT

)

Clears the TIM1's interrupt pending bits.

Parameters:

TIM1_IT

specifies the pending bit to clear. This parameter can be one of the following values: TIM1_IT_UPDATE: TIM1 update Interrupt source TIM1_IT_CC1: TIM1 Capture Compare 1 Interrupt source TIM1_IT_CC2: TIM1 Capture Compare 2 Interrupt source TIM1_IT_CC3: TIM1 Capture Compare 3 Interrupt source TIM1_IT_CC4: TIM1 Capture Compare 4 Interrupt source TIM1_IT_COM: TIM1 Commutation Interrupt source TIM1_IT_TRIGGER: TIM1 Trigger Interrupt source TIM1_IT_BREAK: TIM1 Break Interrupt source

Return values:

None.

Definition at line 2149 of file stm8s_tim1.c.

References IS_TIM1_IT_OK, and TIM1.

void TIM1_Cmd

(

FunctionalState

NewState

)

Enables or disables the TIM1 peripheral.

Parameters:

NewState

new state of the TIM1 peripheral. This parameter can be ENABLE or DISABLE.

Return values:

None

Definition at line 561 of file stm8s_tim1.c.

References DISABLE, IS_FUNCTIONALSTATE_OK, TIM1, and TIM1_CR1_CEN.

void TIM1_CounterModeConfig

(

TIM1_CounterMode_TypeDef

TIM1_CounterMode

)

Specifies the TIM1 Counter Mode to be used.

Parameters:

TIM1_CounterMode

specifies the Counter Mode to be used This parameter can be one of the following values: TIM1_COUNTERMODE_UP: TIM1 Up Counting Mode TIM1_COUNTERMODE_DOWN: TIM1 Down Counting Mode TIM1_COUNTERMODE_CENTERALIGNED1: TIM1 Center Aligned Mode1 TIM1_CounterMode_CenterAligned2: TIM1 Center Aligned Mode2 TIM1_COUNTERMODE_CENTERALIGNED3: TIM1 Center Aligned Mode3

Return values:

None

Definition at line 1048 of file stm8s_tim1.c.

References IS_TIM1_COUNTER_MODE_OK, TIM1, TIM1_CR1_CMS, and TIM1_CR1_DIR.

void TIM1_CtrlPWMOutputs

(

FunctionalState

NewState

)

Enables or disables the TIM1 peripheral Main Outputs.

Parameters:

NewState

new state of the TIM1 peripheral. This parameter can be ENABLE or DISABLE.

Return values:

None

Definition at line 583 of file stm8s_tim1.c.

References DISABLE, IS_FUNCTIONALSTATE_OK, TIM1, and TIM1_BKR_MOE.

void TIM1_DeInit

(

void

)

Deinitializes the TIM1 peripheral registers to their default reset values.

Parameters:

None

Return values:

None

Definition at line 58 of file stm8s_tim1.c.

References TIM1, TIM1_ARRH_RESET_VALUE, TIM1_ARRL_RESET_VALUE, TIM1_BKR_RESET_VALUE, TIM1_CCER1_RESET_VALUE, TIM1_CCER2_RESET_VALUE, TIM1_CCMR1_RESET_VALUE, TIM1_CCMR2_RESET_VALUE, TIM1_CCMR3_RESET_VALUE, TIM1_CCMR4_RESET_VALUE, TIM1_CCR1H_RESET_VALUE, TIM1_CCR1L_RESET_VALUE, TIM1_CCR2H_RESET_VALUE, TIM1_CCR2L_RESET_VALUE, TIM1_CCR3H_RESET_VALUE, TIM1_CCR3L_RESET_VALUE, TIM1_CCR4H_RESET_VALUE, TIM1_CCR4L_RESET_VALUE, TIM1_CNTRH_RESET_VALUE, TIM1_CNTRL_RESET_VALUE, TIM1_CR1_RESET_VALUE, TIM1_CR2_RESET_VALUE, TIM1_DTR_RESET_VALUE, TIM1_ETR_RESET_VALUE, TIM1_IER_RESET_VALUE, TIM1_OISR_RESET_VALUE, TIM1_PSCRH_RESET_VALUE, TIM1_PSCRL_RESET_VALUE, TIM1_RCR_RESET_VALUE, TIM1_SMCR_RESET_VALUE, TIM1_SR1_RESET_VALUE, and TIM1_SR2_RESET_VALUE.

void TIM1_EncoderInterfaceConfig	(	TIM1_EncoderMode_TypeDef	TIM1_EncoderMode,
		TIM1_ICPolarity_TypeDef	TIM1_IC1Polarity,
		TIM1_ICPolarity_TypeDef	TIM1_IC2Polarity
	)

Configures the TIM1 Encoder Interface.

Parameters:

TIM1_EncoderMode	specifies the TIM1 Encoder Mode. This parameter can be one of the following values TIM1_ENCODERMODE_TI1: Counter counts on TI1FP1 edge depending on TI2FP2 level. TIM1_ENCODERMODE_TI2: Counter counts on TI2FP2 edge depending on TI1FP1 level. TIM1_ENCODERMODE_TI12: Counter counts on both TI1FP1 and TI2FP2 edges depending on the level of the other input.
TIM1_IC1Polarity	specifies the IC1 Polarity. This parameter can be one of the following values TIM1_ICPOLARITY_FALLING TIM1_ICPOLARITY_RISING
TIM1_IC2Polarity	specifies the IC2 Polarity. This parameter can be one of the following values TIM1_ICPOLARITY_FALLING TIM1_ICPOLARITY_RISING

Return values:

None

Definition at line 975 of file stm8s_tim1.c.

References CCMR_TIxDirect_Set, IS_TIM1_ENCODER_MODE_OK, IS_TIM1_IC_POLARITY_OK, TIM1, TIM1_CCER1_CC1P, TIM1_CCER1_CC2P, TIM1_CCMR_CCxS, TIM1_ICPOLARITY_RISING, TIM1_SMCR_MSM, and TIM1_SMCR_TS.

void TIM1_ETRClockMode1Config	(	TIM1_ExtTRGPSC_TypeDef	TIM1_ExtTRGPrescaler,
		TIM1_ExtTRGPolarity_TypeDef	TIM1_ExtTRGPolarity,
		uint8_t	ExtTRGFilter
	)

Configures the TIM1 External clock Mode1.

Parameters:

TIM1_ExtTRGPrescaler	specifies the external Trigger Prescaler. This parameter can be one of the following values: TIM1_EXTTRGPSC_OFF TIM1_EXTTRGPSC_DIV2 TIM1_EXTTRGPSC_DIV4 TIM1_EXTTRGPSC_DIV8.
TIM1_ExtTRGPolarity	specifies the external Trigger Polarity. This parameter can be one of the following values: TIM1_EXTTRGPOLARITY_INVERTED TIM1_EXTTRGPOLARITY_NONINVERTED
ExtTRGFilter	specifies the External Trigger Filter. This parameter must be a value between 0x00 and 0x0F

Return values:

None

Definition at line 662 of file stm8s_tim1.c.

References IS_TIM1_EXT_POLARITY_OK, IS_TIM1_EXT_PRESCALER_OK, TIM1, TIM1_ETRConfig(), TIM1_SLAVEMODE_EXTERNAL1, TIM1_SMCR_SMS, TIM1_SMCR_TS, and TIM1_TS_ETRF.

void TIM1_ETRClockMode2Config	(	TIM1_ExtTRGPSC_TypeDef	TIM1_ExtTRGPrescaler,
		TIM1_ExtTRGPolarity_TypeDef	TIM1_ExtTRGPolarity,
		uint8_t	ExtTRGFilter
	)

Configures the TIM1 External clock Mode2.

Parameters:

TIM1_ExtTRGPrescaler	specifies the external Trigger Prescaler. This parameter can be one of the following values: TIM1_EXTTRGPSC_OFF TIM1_EXTTRGPSC_DIV2 TIM1_EXTTRGPSC_DIV4 TIM1_EXTTRGPSC_DIV8.
TIM1_ExtTRGPolarity	specifies the external Trigger Polarity. This parameter can be one of the following values: TIM1_EXTTRGPOLARITY_INVERTED TIM1_EXTTRGPOLARITY_NONINVERTED
ExtTRGFilter	specifies the External Trigger Filter. This parameter must be a value between 0x00 and 0x0F

Return values:

None

Definition at line 694 of file stm8s_tim1.c.

References IS_TIM1_EXT_POLARITY_OK, IS_TIM1_EXT_PRESCALER_OK, TIM1, TIM1_ETR_ECE, and TIM1_ETRConfig().

void TIM1_ETRConfig	(	TIM1_ExtTRGPSC_TypeDef	TIM1_ExtTRGPrescaler,
		TIM1_ExtTRGPolarity_TypeDef	TIM1_ExtTRGPolarity,
		uint8_t	ExtTRGFilter
	)

Configures the TIM1 External Trigger.

Parameters:

TIM1_ExtTRGPrescaler	specifies the external Trigger Prescaler. This parameter can be one of the following values: TIM1_EXTTRGPSC_OFF TIM1_EXTTRGPSC_DIV2 TIM1_EXTTRGPSC_DIV4 TIM1_EXTTRGPSC_DIV8.
TIM1_ExtTRGPolarity	specifies the external Trigger Polarity. This parameter can be one of the following values: TIM1_EXTTRGPOLARITY_INVERTED TIM1_EXTTRGPOLARITY_NONINVERTED
ExtTRGFilter	specifies the External Trigger Filter. This parameter must be a value between 0x00 and 0x0F

Return values:

None

Definition at line 725 of file stm8s_tim1.c.

References IS_TIM1_EXT_TRG_FILTER_OK, and TIM1.

Referenced by TIM1_ETRClockMode1Config(), and TIM1_ETRClockMode2Config().

void TIM1_ForcedOC1Config

(

TIM1_ForcedAction_TypeDef

TIM1_ForcedAction

)

Forces the TIM1 Channel1 output waveform to active or inactive level.

Parameters:

TIM1_ForcedAction

specifies the forced Action to be set to the output waveform. This parameter can be one of the following values: TIM1_FORCEDACTION_ACTIVE: Force active level on OC1REF TIM1_FORCEDACTION_INACTIVE: Force inactive level on OC1REF.

Return values:

None

Definition at line 1067 of file stm8s_tim1.c.

References IS_TIM1_FORCED_ACTION_OK, TIM1, and TIM1_CCMR_OCM.

void TIM1_ForcedOC2Config

(

TIM1_ForcedAction_TypeDef

TIM1_ForcedAction

)

Forces the TIM1 Channel2 output waveform to active or inactive level.

Parameters:

TIM1_ForcedAction

specifies the forced Action to be set to the output waveform. This parameter can be one of the following values: TIM1_FORCEDACTION_ACTIVE: Force active level on OC2REF TIM1_FORCEDACTION_INACTIVE: Force inactive level on OC2REF.

Return values:

None

Definition at line 1085 of file stm8s_tim1.c.

References IS_TIM1_FORCED_ACTION_OK, TIM1, and TIM1_CCMR_OCM.

void TIM1_ForcedOC3Config

(

TIM1_ForcedAction_TypeDef

TIM1_ForcedAction

)

Forces the TIM1 Channel3 output waveform to active or inactive level.

Parameters:

TIM1_ForcedAction

specifies the forced Action to be set to the output waveform. This parameter can be one of the following values: TIM1_FORCEDACTION_ACTIVE: Force active level on OC3REF TIM1_FORCEDACTION_INACTIVE: Force inactive level on OC3REF.

Return values:

None

Definition at line 1104 of file stm8s_tim1.c.

References IS_TIM1_FORCED_ACTION_OK, TIM1, and TIM1_CCMR_OCM.

void TIM1_ForcedOC4Config

(

TIM1_ForcedAction_TypeDef

TIM1_ForcedAction

)

Forces the TIM1 Channel4 output waveform to active or inactive level.

Parameters:

TIM1_ForcedAction

specifies the forced Action to be set to the output waveform. This parameter can be one of the following values: TIM1_FORCEDACTION_ACTIVE: Force active level on OC4REF TIM1_FORCEDACTION_INACTIVE: Force inactive level on OC4REF.

Return values:

None

Definition at line 1123 of file stm8s_tim1.c.

References IS_TIM1_FORCED_ACTION_OK, TIM1, and TIM1_CCMR_OCM.

void TIM1_GenerateEvent

(

TIM1_EventSource_TypeDef

TIM1_EventSource

)

Configures the TIM1 event to be generated by software.

Parameters:

TIM1_EventSource

specifies the event source. This parameter can be one of the following values: TIM1_EVENTSOURCE_UPDATE: TIM1 update Event source TIM1_EVENTSOURCE_CC1: TIM1 Capture Compare 1 Event source TIM1_EVENTSOURCE_CC2: TIM1 Capture Compare 2 Event source TIM1_EVENTSOURCE_CC3: TIM1 Capture Compare 3 Event source TIM1_EVENTSOURCE_CC4: TIM1 Capture Compare 4 Event source TIM1_EVENTSOURCE_COM: TIM1 COM Event source TIM1_EVENTSOURCE_TRIGGER: TIM1 Trigger Event source TIM1_EventSourceBreak: TIM1 Break Event source

Return values:

None

Definition at line 1389 of file stm8s_tim1.c.

References IS_TIM1_EVENT_SOURCE_OK, and TIM1.

uint16_t TIM1_GetCapture1

(

void

)

Gets the TIM1 Input Capture 1 value.

Parameters:

None

Return values:

Capture

Compare 1 Register value.

Definition at line 1922 of file stm8s_tim1.c.

References TIM1.

uint16_t TIM1_GetCapture2

(

void

)

Gets the TIM1 Input Capture 2 value.

Parameters:

None

Return values:

Capture

Compare 2 Register value.

Definition at line 1943 of file stm8s_tim1.c.

References TIM1.

uint16_t TIM1_GetCapture3

(

void

)

Gets the TIM1 Input Capture 3 value.

Parameters:

None

Return values:

Capture

Compare 3 Register value.

Definition at line 1964 of file stm8s_tim1.c.

References TIM1.

uint16_t TIM1_GetCapture4

(

void

)

Gets the TIM1 Input Capture 4 value.

Parameters:

None

Return values:

Capture

Compare 4 Register value.

Definition at line 1984 of file stm8s_tim1.c.

References TIM1.

uint16_t TIM1_GetCounter

(

void

)

Gets the TIM1 Counter value.

Parameters:

None

Return values:

Counter

Register value.

Definition at line 2004 of file stm8s_tim1.c.

References TIM1.

FlagStatus TIM1_GetFlagStatus

(

TIM1_FLAG_TypeDef

TIM1_FLAG

)

Checks whether the specified TIM1 flag is set or not.

Parameters:

TIM1_FLAG

specifies the flag to check. This parameter can be one of the following values: TIM1_FLAG_UPDATE: TIM1 update Flag TIM1_FLAG_CC1: TIM1 Capture Compare 1 Flag TIM1_FLAG_CC2: TIM1 Capture Compare 2 Flag TIM1_FLAG_CC3: TIM1 Capture Compare 3 Flag TIM1_FLAG_CC4: TIM1 Capture Compare 4 Flag TIM1_FLAG_COM: TIM1 Commutation Flag TIM1_FLAG_TRIGGER: TIM1 Trigger Flag TIM1_FLAG_BREAK: TIM1 Break Flag TIM1_FLAG_CC1OF: TIM1 Capture Compare 1 overcapture Flag TIM1_FLAG_CC2OF: TIM1 Capture Compare 2 overcapture Flag TIM1_FLAG_CC3OF: TIM1 Capture Compare 3 overcapture Flag TIM1_FLAG_CC4OF: TIM1 Capture Compare 4 overcapture Flag

Return values:

FlagStatus

The new state of TIM1_FLAG (SET or RESET).

Definition at line 2047 of file stm8s_tim1.c.

References IS_TIM1_GET_FLAG_OK, RESET, SET, and TIM1.

ITStatus TIM1_GetITStatus

(

TIM1_IT_TypeDef

TIM1_IT

)

Checks whether the TIM1 interrupt has occurred or not.

Parameters:

TIM1_IT

specifies the TIM1 interrupt source to check. This parameter can be one of the following values: TIM1_IT_UPDATE: TIM1 update Interrupt source TIM1_IT_CC1: TIM1 Capture Compare 1 Interrupt source TIM1_IT_CC2: TIM1 Capture Compare 2 Interrupt source TIM1_IT_CC3: TIM1 Capture Compare 3 Interrupt source TIM1_IT_CC4: TIM1 Capture Compare 4 Interrupt source TIM1_IT_COM: TIM1 Commutation Interrupt source TIM1_IT_TRIGGER: TIM1 Trigger Interrupt source TIM1_IT_BREAK: TIM1 Break Interrupt source

Return values:

ITStatus

The new state of the TIM1_IT(SET or RESET).

Definition at line 2112 of file stm8s_tim1.c.

References IS_TIM1_GET_IT_OK, RESET, SET, and TIM1.

uint16_t TIM1_GetPrescaler

(

void

)

Gets the TIM1 Prescaler value.

Parameters:

None

Return values:

Prescaler

Register value.

Definition at line 2019 of file stm8s_tim1.c.

References TIM1.

void TIM1_ICInit	(	TIM1_Channel_TypeDef	TIM1_Channel,
		TIM1_ICPolarity_TypeDef	TIM1_ICPolarity,
		TIM1_ICSelection_TypeDef	TIM1_ICSelection,
		TIM1_ICPSC_TypeDef	TIM1_ICPrescaler,
		uint8_t	TIM1_ICFilter
	)

Initializes the TIM1 peripheral according to the specified parameters.

Parameters:

TIM1_Channel	specifies the input capture channel from TIM1_Channel_TypeDef.
TIM1_ICPolarity	specifies the Input capture polarity from TIM1_ICPolarity_TypeDef .
TIM1_ICSelection	specifies the Input capture source selection from TIM1_ICSelection_TypeDef.
TIM1_ICPrescaler	specifies the Input capture Prescaler from TIM1_ICPSC_TypeDef.
TIM1_ICFilter	specifies the Input capture filter value.

Return values:

None

Definition at line 423 of file stm8s_tim1.c.

References IS_TIM1_CHANNEL_OK, IS_TIM1_IC_FILTER_OK, IS_TIM1_IC_POLARITY_OK, IS_TIM1_IC_PRESCALER_OK, IS_TIM1_IC_SELECTION_OK, TI1_Config(), TI2_Config(), TI3_Config(), TI4_Config(), TIM1_CHANNEL_1, TIM1_CHANNEL_2, TIM1_CHANNEL_3, TIM1_SetIC1Prescaler(), TIM1_SetIC2Prescaler(), TIM1_SetIC3Prescaler(), and TIM1_SetIC4Prescaler().

void TIM1_InternalClockConfig

(

void

)

Configures the TIM1 internal Clock.

Parameters:

None

Return values:

None

Definition at line 640 of file stm8s_tim1.c.

References TIM1, and TIM1_SMCR_SMS.

void TIM1_ITConfig	(	TIM1_IT_TypeDef	TIM1_IT,
		FunctionalState	NewState
	)

Enables or disables the specified TIM1 interrupts.

Parameters:

NewState	new state of the TIM1 peripheral. This parameter can be: ENABLE or DISABLE.
TIM1_IT	specifies the TIM1 interrupts sources to be enabled or disabled. This parameter can be any combination of the following values: TIM1_IT_UPDATE: TIM1 update Interrupt source TIM1_IT_CC1: TIM1 Capture Compare 1 Interrupt source TIM1_IT_CC2: TIM1 Capture Compare 2 Interrupt source TIM1_IT_CC3: TIM1 Capture Compare 3 Interrupt source TIM1_IT_CC4: TIM1 Capture Compare 4 Interrupt source TIM1_IT_CCUpdate: TIM1 Capture Compare Update Interrupt source TIM1_IT_TRIGGER: TIM1 Trigger Interrupt source TIM1_IT_BREAK: TIM1 Break Interrupt source
NewState	new state of the TIM1 peripheral.

Return values:

None

Definition at line 617 of file stm8s_tim1.c.

References DISABLE, IS_FUNCTIONALSTATE_OK, IS_TIM1_IT_OK, and TIM1.

void TIM1_OC1FastConfig

(

FunctionalState

NewState

)

Configures the TIM1 Capture Compare 1 Fast feature.

Parameters:

NewState

new state of the Output Compare Fast Enable bit. This parameter can be ENABLE or DISABLE.

Return values:

None

Definition at line 1293 of file stm8s_tim1.c.

References DISABLE, IS_FUNCTIONALSTATE_OK, TIM1, and TIM1_CCMR_OCxFE.

void TIM1_OC1Init	(	TIM1_OCMode_TypeDef	TIM1_OCMode,
		TIM1_OutputState_TypeDef	TIM1_OutputState,
		TIM1_OutputNState_TypeDef	TIM1_OutputNState,
		uint16_t	TIM1_Pulse,
		TIM1_OCPolarity_TypeDef	TIM1_OCPolarity,
		TIM1_OCNPolarity_TypeDef	TIM1_OCNPolarity,
		TIM1_OCIdleState_TypeDef	TIM1_OCIdleState,
		TIM1_OCNIdleState_TypeDef	TIM1_OCNIdleState
	)

Initializes the TIM1 Channel1 according to the specified parameters.

Parameters:

TIM1_OCMode	specifies the Output Compare mode from TIM1_OCMode_TypeDef.
TIM1_OutputState	specifies the Output State from TIM1_OutputState_TypeDef.
TIM1_OutputNState	specifies the Complementary Output State from TIM1_OutputNState_TypeDef.
TIM1_Pulse	specifies the Pulse width value.
TIM1_OCPolarity	specifies the Output Compare Polarity from TIM1_OCPolarity_TypeDef.
TIM1_OCNPolarity	specifies the Complementary Output Compare Polarity from TIM1_OCNPolarity_TypeDef.
TIM1_OCIdleState	specifies the Output Compare Idle State from TIM1_OCIdleState_TypeDef.
TIM1_OCNIdleState	specifies the Complementary Output Compare Idle State from TIM1_OCIdleState_TypeDef.

Return values:

None

Definition at line 154 of file stm8s_tim1.c.

References IS_TIM1_OC_MODE_OK, IS_TIM1_OC_POLARITY_OK, IS_TIM1_OCIDLE_STATE_OK, IS_TIM1_OCN_POLARITY_OK, IS_TIM1_OCNIDLE_STATE_OK, IS_TIM1_OUTPUT_STATE_OK, IS_TIM1_OUTPUTN_STATE_OK, TIM1, TIM1_CCER1_CC1E, TIM1_CCER1_CC1NE, TIM1_CCER1_CC1NP, TIM1_CCER1_CC1P, TIM1_CCMR_OCM, TIM1_OISR_OIS1, and TIM1_OISR_OIS1N.

void TIM1_OC1NPolarityConfig

(

TIM1_OCNPolarity_TypeDef

TIM1_OCNPolarity

)

Configures the TIM1 Channel 1N polarity.

Parameters:

TIM1_OCNPolarity

specifies the OC1N Polarity. This parameter can be one of the following values: TIM1_OCNPOLARITY_LOW: Output Compare active low TIM1_OCNPOLARITY_HIGH: Output Compare active high

Return values:

None

Definition at line 1430 of file stm8s_tim1.c.

References IS_TIM1_OCN_POLARITY_OK, TIM1, TIM1_CCER1_CC1NP, and TIM1_OCNPOLARITY_HIGH.

void TIM1_OC1PolarityConfig

(

TIM1_OCPolarity_TypeDef

TIM1_OCPolarity

)

Configures the TIM1 Channel 1 polarity.

Parameters:

TIM1_OCPolarity

specifies the OC1 Polarity. This parameter can be one of the following values: TIM1_OCPOLARITY_LOW: Output Compare active low TIM1_OCPOLARITY_HIGH: Output Compare active high

Return values:

None

Definition at line 1406 of file stm8s_tim1.c.

References IS_TIM1_OC_POLARITY_OK, TIM1, TIM1_CCER1_CC1P, and TIM1_OCPOLARITY_HIGH.

void TIM1_OC1PreloadConfig

(

FunctionalState

NewState

)

Enables or disables the TIM1 peripheral Preload Register on CCR1.

Parameters:

NewState

new state of the Capture Compare Preload register. This parameter can be ENABLE or DISABLE.

Return values:

None

Definition at line 1205 of file stm8s_tim1.c.

References DISABLE, IS_FUNCTIONALSTATE_OK, TIM1, and TIM1_CCMR_OCxPE.

void TIM1_OC2FastConfig

(

FunctionalState

NewState

)

Configures the TIM1 Capture Compare 2 Fast feature.

Parameters:

NewState

new state of the Output Compare Fast Enable bit. This parameter can be ENABLE or DISABLE.

Return values:

None

Definition at line 1315 of file stm8s_tim1.c.

References DISABLE, IS_FUNCTIONALSTATE_OK, TIM1, and TIM1_CCMR_OCxFE.

void TIM1_OC2Init	(	TIM1_OCMode_TypeDef	TIM1_OCMode,
		TIM1_OutputState_TypeDef	TIM1_OutputState,
		TIM1_OutputNState_TypeDef	TIM1_OutputNState,
		uint16_t	TIM1_Pulse,
		TIM1_OCPolarity_TypeDef	TIM1_OCPolarity,
		TIM1_OCNPolarity_TypeDef	TIM1_OCNPolarity,
		TIM1_OCIdleState_TypeDef	TIM1_OCIdleState,
		TIM1_OCNIdleState_TypeDef	TIM1_OCNIdleState
	)

Initializes the TIM1 Channel2 according to the specified parameters.

Parameters:

TIM1_OCMode	specifies the Output Compare mode from TIM1_OCMode_TypeDef.
TIM1_OutputState	specifies the Output State from TIM1_OutputState_TypeDef.
TIM1_OutputNState	specifies the Complementary Output State from TIM1_OutputNState_TypeDef.
TIM1_Pulse	specifies the Pulse width value.
TIM1_OCPolarity	specifies the Output Compare Polarity from TIM1_OCPolarity_TypeDef.
TIM1_OCNPolarity	specifies the Complementary Output Compare Polarity from TIM1_OCNPolarity_TypeDef.
TIM1_OCIdleState	specifies the Output Compare Idle State from TIM1_OCIdleState_TypeDef.
TIM1_OCNIdleState	specifies the Complementary Output Compare Idle State from TIM1_OCIdleState_TypeDef.

Return values:

None

Definition at line 217 of file stm8s_tim1.c.

References IS_TIM1_OC_MODE_OK, IS_TIM1_OC_POLARITY_OK, IS_TIM1_OCIDLE_STATE_OK, IS_TIM1_OCN_POLARITY_OK, IS_TIM1_OCNIDLE_STATE_OK, IS_TIM1_OUTPUT_STATE_OK, IS_TIM1_OUTPUTN_STATE_OK, TIM1, TIM1_CCER1_CC2E, TIM1_CCER1_CC2NE, TIM1_CCER1_CC2NP, TIM1_CCER1_CC2P, TIM1_CCMR_OCM, TIM1_OISR_OIS2, and TIM1_OISR_OIS2N.

void TIM1_OC2NPolarityConfig

(

TIM1_OCNPolarity_TypeDef

TIM1_OCNPolarity

)

Configures the TIM1 Channel 2N polarity.

Parameters:

TIM1_OCNPolarity

specifies the OC2N Polarity. This parameter can be one of the following values: TIM1_OCNPOLARITY_LOW: Output Compare active low TIM1_OCNPOLARITY_HIGH: Output Compare active high

Return values:

None

Definition at line 1478 of file stm8s_tim1.c.

References IS_TIM1_OCN_POLARITY_OK, TIM1, TIM1_CCER1_CC2NP, and TIM1_OCNPOLARITY_HIGH.

void TIM1_OC2PolarityConfig

(

TIM1_OCPolarity_TypeDef

TIM1_OCPolarity

)

Configures the TIM1 Channel 2 polarity.

Parameters:

TIM1_OCPolarity

specifies the OC2 Polarity. This parameter can be one of the following values: TIM1_OCPOLARITY_LOW: Output Compare active low TIM1_OCPOLARITY_HIGH: Output Compare active high

Return values:

None

Definition at line 1454 of file stm8s_tim1.c.

References IS_TIM1_OC_POLARITY_OK, TIM1, TIM1_CCER1_CC2P, and TIM1_OCPOLARITY_HIGH.

void TIM1_OC2PreloadConfig

(

FunctionalState

NewState

)

Enables or disables the TIM1 peripheral Preload Register on CCR2.

Parameters:

NewState

new state of the Capture Compare Preload register. This parameter can be ENABLE or DISABLE.

Return values:

None

Definition at line 1227 of file stm8s_tim1.c.

References DISABLE, IS_FUNCTIONALSTATE_OK, TIM1, and TIM1_CCMR_OCxPE.

void TIM1_OC3FastConfig

(

FunctionalState

NewState

)

Configures the TIM1 Capture Compare 3 Fast feature.

Parameters:

NewState

new state of the Output Compare Fast Enable bit. This parameter can be ENABLE or DISABLE.

Return values:

None

Definition at line 1337 of file stm8s_tim1.c.

References DISABLE, IS_FUNCTIONALSTATE_OK, TIM1, and TIM1_CCMR_OCxFE.

void TIM1_OC3Init	(	TIM1_OCMode_TypeDef	TIM1_OCMode,
		TIM1_OutputState_TypeDef	TIM1_OutputState,
		TIM1_OutputNState_TypeDef	TIM1_OutputNState,
		uint16_t	TIM1_Pulse,
		TIM1_OCPolarity_TypeDef	TIM1_OCPolarity,
		TIM1_OCNPolarity_TypeDef	TIM1_OCNPolarity,
		TIM1_OCIdleState_TypeDef	TIM1_OCIdleState,
		TIM1_OCNIdleState_TypeDef	TIM1_OCNIdleState
	)

Initializes the TIM1 Channel3 according to the specified parameters.

Parameters:

TIM1_OCMode	specifies the Output Compare mode from TIM1_OCMode_TypeDef.
TIM1_OutputState	specifies the Output State from TIM1_OutputState_TypeDef.
TIM1_OutputNState	specifies the Complementary Output State from TIM1_OutputNState_TypeDef.
TIM1_Pulse	specifies the Pulse width value.
TIM1_OCPolarity	specifies the Output Compare Polarity from TIM1_OCPolarity_TypeDef.
TIM1_OCNPolarity	specifies the Complementary Output Compare Polarity from TIM1_OCNPolarity_TypeDef.
TIM1_OCIdleState	specifies the Output Compare Idle State from TIM1_OCIdleState_TypeDef.
TIM1_OCNIdleState	specifies the Complementary Output Compare Idle State from TIM1_OCIdleState_TypeDef.

Return values:

None

Definition at line 281 of file stm8s_tim1.c.

References IS_TIM1_OC_MODE_OK, IS_TIM1_OC_POLARITY_OK, IS_TIM1_OCIDLE_STATE_OK, IS_TIM1_OCN_POLARITY_OK, IS_TIM1_OCNIDLE_STATE_OK, IS_TIM1_OUTPUT_STATE_OK, IS_TIM1_OUTPUTN_STATE_OK, TIM1, TIM1_CCER2_CC3E, TIM1_CCER2_CC3NE, TIM1_CCER2_CC3NP, TIM1_CCER2_CC3P, TIM1_CCMR_OCM, TIM1_OISR_OIS3, and TIM1_OISR_OIS3N.

void TIM1_OC3NPolarityConfig

(

TIM1_OCNPolarity_TypeDef

TIM1_OCNPolarity

)

Configures the TIM1 Channel 3N polarity.

Parameters:

TIM1_OCNPolarity

specifies the OC3N Polarity. This parameter can be one of the following values: TIM1_OCNPOLARITY_LOW: Output Compare active low TIM1_OCNPOLARITY_HIGH: Output Compare active high

Return values:

None

Definition at line 1527 of file stm8s_tim1.c.

References IS_TIM1_OCN_POLARITY_OK, TIM1, TIM1_CCER2_CC3NP, and TIM1_OCNPOLARITY_HIGH.

void TIM1_OC3PolarityConfig

(

TIM1_OCPolarity_TypeDef

TIM1_OCPolarity

)

Configures the TIM1 Channel 3 polarity.

Parameters:

TIM1_OCPolarity

specifies the OC3 Polarity. This parameter can be one of the following values: TIM1_OCPOLARITY_LOW: Output Compare active low TIM1_OCPOLARITY_HIGH: Output Compare active high

Return values:

None

Definition at line 1502 of file stm8s_tim1.c.

References IS_TIM1_OC_POLARITY_OK, TIM1, TIM1_CCER2_CC3P, and TIM1_OCPOLARITY_HIGH.

void TIM1_OC3PreloadConfig

(

FunctionalState

NewState

)

Enables or disables the TIM1 peripheral Preload Register on CCR3.

Parameters:

NewState

new state of the Capture Compare Preload register. This parameter can be ENABLE or DISABLE.

Return values:

None

Definition at line 1249 of file stm8s_tim1.c.

References DISABLE, IS_FUNCTIONALSTATE_OK, TIM1, and TIM1_CCMR_OCxPE.

void TIM1_OC4FastConfig

(

FunctionalState

NewState

)

Configures the TIM1 Capture Compare 4 Fast feature.

Parameters:

NewState

new state of the Output Compare Fast Enable bit. This parameter can be ENABLE or DISABLE.

Return values:

None

Definition at line 1359 of file stm8s_tim1.c.

References DISABLE, IS_FUNCTIONALSTATE_OK, TIM1, and TIM1_CCMR_OCxFE.

void TIM1_OC4Init	(	TIM1_OCMode_TypeDef	TIM1_OCMode,
		TIM1_OutputState_TypeDef	TIM1_OutputState,
		uint16_t	TIM1_Pulse,
		TIM1_OCPolarity_TypeDef	TIM1_OCPolarity,
		TIM1_OCIdleState_TypeDef	TIM1_OCIdleState
	)

Initializes the TIM1 Channel4 according to the specified parameters.

Parameters:

TIM1_OCMode	specifies the Output Compare mode from TIM1_OCMode_TypeDef.
TIM1_OutputState	specifies the Output State from TIM1_OutputState_TypeDef.
TIM1_Pulse	specifies the Pulse width value.
TIM1_OCPolarity	specifies the Output Compare Polarity from TIM1_OCPolarity_TypeDef.
TIM1_OCIdleState	specifies the Output Compare Idle State from TIM1_OCIdleState_TypeDef.

Return values:

None

Definition at line 338 of file stm8s_tim1.c.

References IS_TIM1_OC_MODE_OK, IS_TIM1_OC_POLARITY_OK, IS_TIM1_OCIDLE_STATE_OK, IS_TIM1_OUTPUT_STATE_OK, TIM1, TIM1_CCER2_CC4E, TIM1_CCER2_CC4P, TIM1_CCMR_OCM, TIM1_OCIDLESTATE_RESET, and TIM1_OISR_OIS4.

void TIM1_OC4PolarityConfig

(

TIM1_OCPolarity_TypeDef

TIM1_OCPolarity

)

Configures the TIM1 Channel 4 polarity.

Parameters:

TIM1_OCPolarity

specifies the OC4 Polarity. This parameter can be one of the following values: TIM1_OCPOLARITY_LOW: Output Compare active low TIM1_OCPOLARITY_HIGH: Output Compare active high

Return values:

None

Definition at line 1551 of file stm8s_tim1.c.

References IS_TIM1_OC_POLARITY_OK, TIM1, TIM1_CCER2_CC4P, and TIM1_OCPOLARITY_HIGH.

void TIM1_OC4PreloadConfig

(

FunctionalState

NewState

)

Enables or disables the TIM1 peripheral Preload Register on CCR4.

Parameters:

NewState

new state of the Capture Compare Preload register. This parameter can be ENABLE or DISABLE.

Return values:

None

Definition at line 1271 of file stm8s_tim1.c.

References DISABLE, IS_FUNCTIONALSTATE_OK, TIM1, and TIM1_CCMR_OCxPE.

void TIM1_PrescalerConfig	(	uint16_t	Prescaler,
		TIM1_PSCReloadMode_TypeDef	TIM1_PSCReloadMode
	)

Configures the TIM1 Prescaler.

Parameters:

Prescaler	specifies the Prescaler Register value This parameter must be a value between 0x0000 and 0xFFFF
TIM1_PSCReloadMode	specifies the TIM1 Prescaler Reload mode. This parameter can be one of the following values TIM1_PSCRELOADMODE_IMMEDIATE: The Prescaler is loaded immediately. TIM1_PSCRELOADMODE_UPDATE: The Prescaler is loaded at the update event.

Return values:

None

Definition at line 1023 of file stm8s_tim1.c.

References IS_TIM1_PRESCALER_RELOAD_OK, and TIM1.

void TIM1_PWMIConfig	(	TIM1_Channel_TypeDef	TIM1_Channel,
		TIM1_ICPolarity_TypeDef	TIM1_ICPolarity,
		TIM1_ICSelection_TypeDef	TIM1_ICSelection,
		TIM1_ICPSC_TypeDef	TIM1_ICPrescaler,
		uint8_t	TIM1_ICFilter
	)

Configures the TIM1 peripheral in PWM Input Mode according to the specified parameters.

Parameters:

TIM1_Channel	specifies the input capture channel from TIM1_Channel_TypeDef.
TIM1_ICPolarity	specifies the Input capture polarity from TIM1_ICPolarity_TypeDef .
TIM1_ICSelection	specifies the Input capture source selection from TIM1_ICSelection_TypeDef.
TIM1_ICPrescaler	specifies the Input capture Prescaler from TIM1_ICPSC_TypeDef.
TIM1_ICFilter	specifies the Input capture filter value.

Return values:

None

Definition at line 488 of file stm8s_tim1.c.

References IS_TIM1_IC_POLARITY_OK, IS_TIM1_IC_PRESCALER_OK, IS_TIM1_IC_SELECTION_OK, IS_TIM1_PWMI_CHANNEL_OK, TI1_Config(), TI2_Config(), TIM1_CHANNEL_1, TIM1_ICPOLARITY_FALLING, TIM1_ICPOLARITY_RISING, TIM1_ICSELECTION_DIRECTTI, TIM1_ICSELECTION_INDIRECTTI, TIM1_SetIC1Prescaler(), and TIM1_SetIC2Prescaler().

void TIM1_SelectCOM

(

FunctionalState

NewState

)

Selects the TIM1 peripheral Commutation event.

Parameters:

NewState

new state of the Commutation event. This parameter can be ENABLE or DISABLE.

Return values:

None

Definition at line 1161 of file stm8s_tim1.c.

References DISABLE, IS_FUNCTIONALSTATE_OK, TIM1, and TIM1_CR2_COMS.

void TIM1_SelectHallSensor

(

FunctionalState

NewState

)

Enables or Disables the TIM1�s Hall sensor interface.

Parameters:

NewState

new state of the TIM1 Hall sensor interface.This parameter can be ENABLE or DISABLE.

Return values:

None

Definition at line 849 of file stm8s_tim1.c.

References DISABLE, IS_FUNCTIONALSTATE_OK, TIM1, and TIM1_CR2_TI1S.

void TIM1_SelectInputTrigger

(

TIM1_TS_TypeDef

TIM1_InputTriggerSource

)

Selects the TIM1 Input Trigger source.

Parameters:

TIM1_InputTriggerSource

specifies Input Trigger source. This parameter can be one of the following values: TIM1_TS_TI1F_ED: TI1 Edge Detector TIM1_TS_TI1FP1: Filtered Timer Input 1 TIM1_TS_TI2FP2: Filtered Timer Input 2 TIM1_TS_ETRF: External Trigger input

Return values:

None

Definition at line 787 of file stm8s_tim1.c.

References IS_TIM1_TRIGGER_SELECTION_OK, TIM1, and TIM1_SMCR_TS.

Referenced by TIM1_TIxExternalClockConfig().

void TIM1_SelectMasterSlaveMode

(

FunctionalState

NewState

)

Sets or Resets the TIM1 Master/Slave Mode.

Parameters:

NewState

new state of the synchronization between TIM1 and its slaves (through TRGO). This parameter can be ENABLE or DISABLE.

Return values:

None

Definition at line 939 of file stm8s_tim1.c.

References DISABLE, IS_FUNCTIONALSTATE_OK, TIM1, and TIM1_SMCR_MSM.

void TIM1_SelectOCxM	(	TIM1_Channel_TypeDef	TIM1_Channel,
		TIM1_OCMode_TypeDef	TIM1_OCMode
	)

Selects the TIM1 Output Compare Mode.

This function disables the selected channel before changing the Output Compare Mode. User has to enable this channel using TIM1_CCxCmd and TIM1_CCxNCmd functions.

Parameters:

TIM1_Channel	specifies the TIM1 Channel. This parameter can be one of the following values: TIM1_CHANNEL_1: TIM1 Channel1 TIM1_CHANNEL_2: TIM1 Channel2 TIM1_CHANNEL_3: TIM1 Channel3 TIM1_CHANNEL_4: TIM1 Channel4
TIM1_OCMode	specifies the TIM1 Output Compare Mode. This parameter can be one of the following values: TIM1_OCMODE_TIMING TIM1_OCMODE_ACTIVE TIM1_OCMODE_TOGGLE TIM1_OCMODE_PWM1 TIM1_OCMODE_PWM2 TIM1_FORCEDACTION_ACTIVE TIM1_FORCEDACTION_INACTIVE

Return values:

None

Definition at line 1712 of file stm8s_tim1.c.

References IS_TIM1_CHANNEL_OK, IS_TIM1_OCM_OK, TIM1, TIM1_CCER1_CC1E, TIM1_CCER1_CC2E, TIM1_CCER2_CC3E, TIM1_CCER2_CC4E, TIM1_CCMR_OCM, TIM1_CHANNEL_1, TIM1_CHANNEL_2, and TIM1_CHANNEL_3.

void TIM1_SelectOnePulseMode

(

TIM1_OPMode_TypeDef

TIM1_OPMode

)

Selects the TIM1�s One Pulse Mode.

Parameters:

TIM1_OPMode

specifies the OPM Mode to be used. This parameter can be one of the following values TIM1_OPMODE_SINGLE TIM1_OPMODE_REPETITIVE

Return values:

None

Definition at line 873 of file stm8s_tim1.c.

References IS_TIM1_OPM_MODE_OK, TIM1, TIM1_CR1_OPM, and TIM1_OPMODE_REPETITIVE.

void TIM1_SelectOutputTrigger

(

TIM1_TRGOSource_TypeDef

TIM1_TRGOSource

)

Selects the TIM1 Trigger Output Mode.

Parameters:

TIM1_TRGOSource

specifies the Trigger Output source. This parameter can be one of the following values TIM1_TRGOSOURCE_RESET TIM1_TRGOSOURCE_ENABLE TIM1_TRGOSOURCE_UPDATE TIM1_TRGOSource_OC1 TIM1_TRGOSOURCE_OC1REF TIM1_TRGOSOURCE_OC2REF TIM1_TRGOSOURCE_OC3REF

Return values:

None

Definition at line 903 of file stm8s_tim1.c.

References IS_TIM1_TRGO_SOURCE_OK, TIM1, and TIM1_CR2_MMS.

void TIM1_SelectSlaveMode

(

TIM1_SlaveMode_TypeDef

TIM1_SlaveMode

)

Selects the TIM1 Slave Mode.

Parameters:

TIM1_SlaveMode

specifies the TIM1 Slave Mode. This parameter can be one of the following values TIM1_SLAVEMODE_RESET TIM1_SLAVEMODE_GATED TIM1_SLAVEMODE_TRIGGER TIM1_SLAVEMODE_EXTERNAL1

Return values:

None

Definition at line 923 of file stm8s_tim1.c.

References IS_TIM1_SLAVE_MODE_OK, TIM1, and TIM1_SMCR_SMS.

void TIM1_SetAutoreload

(

uint16_t

Autoreload

)

Sets the TIM1 Autoreload Register value.

Parameters:

Autoreload

specifies the Autoreload register new value. This parameter is between 0x0000 and 0xFFFF.

Return values:

None

Definition at line 1775 of file stm8s_tim1.c.

References TIM1.

void TIM1_SetCompare1

(

uint16_t

Compare1

)

Sets the TIM1 Capture Compare1 Register value.

Parameters:

Compare1

specifies the Capture Compare1 register new value. This parameter is between 0x0000 and 0xFFFF.

Return values:

None

Definition at line 1788 of file stm8s_tim1.c.

References TIM1.

void TIM1_SetCompare2

(

uint16_t

Compare2

)

Sets the TIM1 Capture Compare2 Register value.

Parameters:

Compare2

specifies the Capture Compare2 register new value. This parameter is between 0x0000 and 0xFFFF.

Return values:

None

Definition at line 1801 of file stm8s_tim1.c.

References TIM1.

void TIM1_SetCompare3

(

uint16_t

Compare3

)

Sets the TIM1 Capture Compare3 Register value.

Parameters:

Compare3

specifies the Capture Compare3 register new value. This parameter is between 0x0000 and 0xFFFF.

Return values:

None

Definition at line 1814 of file stm8s_tim1.c.

References TIM1.

void TIM1_SetCompare4

(

uint16_t

Compare4

)

Sets the TIM1 Capture Compare4 Register value.

Parameters:

Compare4

specifies the Capture Compare4 register new value. This parameter is between 0x0000 and 0xFFFF.

Return values:

None

Definition at line 1827 of file stm8s_tim1.c.

References TIM1.

void TIM1_SetCounter

(

uint16_t

Counter

)

Sets the TIM1 Counter Register value.

Parameters:

Counter

specifies the Counter register new value. This parameter is between 0x0000 and 0xFFFF.

Return values:

None

Definition at line 1762 of file stm8s_tim1.c.

References TIM1.

void TIM1_SetIC1Prescaler

(

TIM1_ICPSC_TypeDef

TIM1_IC1Prescaler

)

Sets the TIM1 Input Capture 1 prescaler.

Parameters:

TIM1_IC1Prescaler

specifies the Input Capture prescaler new value This parameter can be one of the following values: TIM1_ICPSC_DIV1: no prescaler TIM1_ICPSC_DIV2: capture is done once every 2 events TIM1_ICPSC_DIV4: capture is done once every 4 events TIM1_ICPSC_DIV8: capture is done once every 8 events

Return values:

None

Definition at line 1844 of file stm8s_tim1.c.

References IS_TIM1_IC_PRESCALER_OK, TIM1, and TIM1_CCMR_ICxPSC.

Referenced by TIM1_ICInit(), and TIM1_PWMIConfig().

void TIM1_SetIC2Prescaler

(

TIM1_ICPSC_TypeDef

TIM1_IC2Prescaler

)

Sets the TIM1 Input Capture 2 prescaler.

Parameters:

TIM1_IC2Prescaler

specifies the Input Capture prescaler new value This parameter can be one of the following values: TIM1_ICPSC_DIV1: no prescaler TIM1_ICPSC_DIV2: capture is done once every 2 events TIM1_ICPSC_DIV4: capture is done once every 4 events TIM1_ICPSC_DIV8: capture is done once every 8 events

Return values:

None

Definition at line 1864 of file stm8s_tim1.c.

References IS_TIM1_IC_PRESCALER_OK, TIM1, and TIM1_CCMR_ICxPSC.

Referenced by TIM1_ICInit(), and TIM1_PWMIConfig().

void TIM1_SetIC3Prescaler

(

TIM1_ICPSC_TypeDef

TIM1_IC3Prescaler

)

Sets the TIM1 Input Capture 3 prescaler.

Parameters:

TIM1_IC3Prescaler

specifies the Input Capture prescaler new value This parameter can be one of the following values: TIM1_ICPSC_DIV1: no prescaler TIM1_ICPSC_DIV2: capture is done once every 2 events TIM1_ICPSC_DIV4: capture is done once every 4 events TIM1_ICPSC_DIV8: capture is done once every 8 events

Return values:

None

Definition at line 1885 of file stm8s_tim1.c.

References IS_TIM1_IC_PRESCALER_OK, TIM1, and TIM1_CCMR_ICxPSC.

Referenced by TIM1_ICInit().

void TIM1_SetIC4Prescaler

(

TIM1_ICPSC_TypeDef

TIM1_IC4Prescaler

)

Sets the TIM1 Input Capture 4 prescaler.

Parameters:

TIM1_IC4Prescaler

specifies the Input Capture prescaler new value This parameter can be one of the following values: TIM1_ICPSC_DIV1: no prescaler TIM1_ICPSC_DIV2: capture is done once every 2 events TIM1_ICPSC_DIV4: capture is done once every 4 events TIM1_ICPSC_DIV8: capture is done once every 8 events

Return values:

None

Definition at line 1906 of file stm8s_tim1.c.

References IS_TIM1_IC_PRESCALER_OK, TIM1, and TIM1_CCMR_ICxPSC.

Referenced by TIM1_ICInit().

void TIM1_TimeBaseInit	(	uint16_t	TIM1_Prescaler,
		TIM1_CounterMode_TypeDef	TIM1_CounterMode,
		uint16_t	TIM1_Period,
		uint8_t	TIM1_RepetitionCounter
	)

Initializes the TIM1 Time Base Unit according to the specified parameters.

Parameters:

TIM1_Prescaler	specifies the Prescaler value.
TIM1_CounterMode	specifies the counter mode from TIM1_CounterMode_TypeDef .
TIM1_Period	specifies the Period value.
TIM1_RepetitionCounter	specifies the Repetition counter value

Return values:

None

Definition at line 111 of file stm8s_tim1.c.

References IS_TIM1_COUNTER_MODE_OK, TIM1, TIM1_CR1_CMS, and TIM1_CR1_DIR.

void TIM1_TIxExternalClockConfig	(	TIM1_TIxExternalCLK1Source_TypeDef	TIM1_TIxExternalCLKSource,
		TIM1_ICPolarity_TypeDef	TIM1_ICPolarity,
		uint8_t	ICFilter
	)

Configures the TIM1 Trigger as External Clock.

Parameters:

TIM1_TIxExternalCLKSource	specifies Trigger source. This parameter can be one of the following values: TIM1_TIXEXTERNALCLK1SOURCE_TI1: TI1 Edge Detector TIM1_TIXEXTERNALCLK1SOURCE_TI2: Filtered TIM1 Input 1 TIM1_TIXEXTERNALCLK1SOURCE_TI1ED: Filtered TIM1 Input 2
TIM1_ICPolarity	specifies the TIx Polarity. This parameter can be: TIM1_ICPOLARITY_RISING TIM1_ICPOLARITY_FALLING
ICFilter	specifies the filter value. This parameter must be a value between 0x00 and 0x0F

Return values:

None

Definition at line 751 of file stm8s_tim1.c.

References IS_TIM1_IC_FILTER_OK, IS_TIM1_IC_POLARITY_OK, IS_TIM1_TIXCLK_SOURCE_OK, TI1_Config(), TI2_Config(), TIM1, TIM1_ICSELECTION_DIRECTTI, TIM1_SelectInputTrigger(), TIM1_SLAVEMODE_EXTERNAL1, and TIM1_TIXEXTERNALCLK1SOURCE_TI2.

void TIM1_UpdateDisableConfig

(

FunctionalState

NewState

)

Enables or Disables the TIM1 Update event.

Parameters:

NewState

new state of the TIM1 peripheral Preload register. This parameter can be ENABLE or DISABLE.

Return values:

None

Definition at line 803 of file stm8s_tim1.c.

References DISABLE, IS_FUNCTIONALSTATE_OK, TIM1, and TIM1_CR1_UDIS.

void TIM1_UpdateRequestConfig

(

TIM1_UpdateSource_TypeDef

TIM1_UpdateSource

)

Selects the TIM1 Update Request Interrupt source.

Parameters:

TIM1_UpdateSource

specifies the Update source. This parameter can be one of the following values TIM1_UPDATESOURCE_REGULAR TIM1_UPDATESOURCE_GLOBAL

Return values:

None

Definition at line 827 of file stm8s_tim1.c.

References IS_TIM1_UPDATE_SOURCE_OK, TIM1, TIM1_CR1_URS, and TIM1_UPDATESOURCE_GLOBAL.