IO.Ethernet.IPSelect

Driver Modicon Modbus

previous page next page

IO.Ethernet.IPSelect

Type of Tag	I/O Tag
Type of Access	Reading or Writing
N1 Parameter	-1
N2 Parameter	0
N3 Parameter	4
N4 Parameter	0
String Configuration	IO.Ethernet.IPSelect

Indicates the active IP address. Possible values are the following:

·0: The main IP address is selected

·1: The alternative (backup) IP address is selected

If the Ethernet (or RAS) Interface is connected, this Tag indicates which of the two IP addresses configured is in use. If the Interface is disconnected, this Tag indicates which IP address is used first on the next connection attempt.

During the connection process, if the active IP address is not available, the I/O Interface tries to connect using the other IP address. If the connection with the alternative IP address works, this one is configured as the active IP address (automatic switchover).

To force a manual switchover, write the value 1 (one) or 0 (zero) to this Tag. This forces a reconnection with the specified IP address (0: Main IP address or 1: Alternative IP address) if the Driver is currently connected. If the Driver is disconnected, this Tag configures the active IP address for the next connection attempt.


Has this section of the documentation helped you configure this Driver?
Yes	No
Comments (optional):
</td> </tr> <tr class="calibre14"> <td colspan="2" class="calibre16"> <span id="txtCounter" class="contador">There are 150 characters left.</span> </td> </tr> <tr class="calibre14"> <td colspan="2" class="texto1">Contact (optional):</td> </tr> <tr class="calibre14"> <td colspan="2" class="calibre16"> <input id="txtContact" type="text" class="contato" title="E-mail or phone contact (50 characters)" name="texto_contato" maxlength="50"/> </td> </tr> <tr class="calibre17"> <td colspan="2" class="calibre16"> <input type="button" class="texto2" value="Reset" title="Clear form fields" onclick="javascript:resetForm()"/> <input type="button" class="texto2" value="Send" title="Send data to Elipse Software" onclick="javascript:validaSubmit(this.form)"/> </td> </tr> <tr class="calibre15"> <td colspan="2" class="calibre16"> <span class="texto2">Check our <a href="http://kb.elipse.com.br/en-us" title="Elipse Knowledgebase" target="_blank" class="calibre18 pcalibre">Knowledgebase</a> for more information about our products</span> </td> </tr> </table> </form> </div> <div class="calibreEbNav"> <a href="manual_ethernet_iotag.html" class="calibreAPrev">previous page</a> <a href="./" class="calibreAHome"> start</a> <a href="manual_ethernet_iotag_ipswitch.html" class="calibreANext"> next page</a> </div> </div> </table> </div> </section> <!-- Section <section> <header class="major"> <h2>Ipsum sed dolor</h2> </header> <div class="posts"> <article> <a href="#" class="image"><img src="images/pic01.jpg" alt="" /></a> <h3>Interdum aenean</h3> <p>Aenean ornare velit lacus, ac varius enim lorem ullamcorper dolore. Proin aliquam facilisis ante interdum. Sed nulla amet lorem feugiat tempus aliquam.</p> <ul class="actions"> <li><a href="#" class="button">More</a></li> </ul> </article> <article> <a href="#" class="image"><img src="images/pic02.jpg" alt="" /></a> <h3>Nulla amet dolore</h3> <p>Aenean ornare velit lacus, ac varius enim lorem ullamcorper dolore. Proin aliquam facilisis ante interdum. Sed nulla amet lorem feugiat tempus aliquam.</p> <ul class="actions"> <li><a href="#" class="button">More</a></li> </ul> </article> <article> <a href="#" class="image"><img src="images/pic03.jpg" alt="" /></a> <h3>Tempus ullamcorper</h3> <p>Aenean ornare velit lacus, ac varius enim lorem ullamcorper dolore. Proin aliquam facilisis ante interdum. Sed nulla amet lorem feugiat tempus aliquam.</p> <ul class="actions"> <li><a href="#" class="button">More</a></li> </ul> </article> <article> <a href="#" class="image"><img src="images/pic04.jpg" alt="" /></a> <h3>Sed etiam facilis</h3> <p>Aenean ornare velit lacus, ac varius enim lorem ullamcorper dolore. Proin aliquam facilisis ante interdum. Sed nulla amet lorem feugiat tempus aliquam.</p> <ul class="actions"> <li><a href="#" class="button">More</a></li> </ul> </article> <article> <a href="#" class="image"><img src="images/pic05.jpg" alt="" /></a> <h3>Feugiat lorem aenean</h3> <p>Aenean ornare velit lacus, ac varius enim lorem ullamcorper dolore. Proin aliquam facilisis ante interdum. Sed nulla amet lorem feugiat tempus aliquam.</p> <ul class="actions"> <li><a href="#" class="button">More</a></li> </ul> </article> <article> <a href="#" class="image"><img src="images/pic06.jpg" alt="" /></a> <h3>Amet varius aliquam</h3> <p>Aenean ornare velit lacus, ac varius enim lorem ullamcorper dolore. Proin aliquam facilisis ante interdum. Sed nulla amet lorem feugiat tempus aliquam.</p> <ul class="actions"> <li><a href="#" class="button">More</a></li> </ul> </article> </div> </section> --> </div> </div> <!-- Sidebar --> <!-- Sidebar --> <div id="sidebar"> <div class="inner"> <!-- Search <section id="search" class="alt"> <form method="get" action="https://arb.parts/eo-search.php"> <input type="text" name="executiveorder" id="eo" placeholder="E.O. Number" /> <input type="submit" value="Search E.O." /></form> </section> --> <!-- Menu --> <nav id="menu"> <header class="major"> <h2>Menu</h2> </header> <ul> <li><a href="https://documentation.help/">Homepage</a></li> <!-- <li> <span class="opener">Approved Vehicles</span> <ul> <li><a href="#">Motorcycles</a></li> <li><a href="#">On-Road Vehicles</a></li> <li><a href="#">Off-Road Vehicles</a></li> <li><a href="#">Compression Engines</a></li> </ul> </li> <li><a href="https://arb.parts/Contact-Us">Contact Us</a></li> <li><a href="https://arb.parts/About-Us">About Us</a></li> --> </ul> <div><div class="calibreTocIndex"> <h2> Table of contents</h2> <div> <ul> <li> <a href="modbus_intro.html">Modicon Modbus Driver</a> </li> <li> <a href="modbus_quick_config_guide.html">Quick Configuration Guide</a> <ul> <li> <a href="modbus_quick_config_guide_insert_driver.html">Inserting a Driver</a> <ul> <li> <a href="modbus_add_application.html">Adding a Driver to an Elipse Software Application</a> <ul> <li> <a href="modbus_add_application_e3_power.html">E3 or Elipse Power</a> </li> <li> <a href="modbus_add_application_scada.html">Elipse SCADA</a> </li> </ul> </li> </ul> </li> <li> <a href="modbus_quick_config_guide_config_driver.html">Configuring a Driver</a> </li> <li> <a href="modbus_quick_config_guide_config_iotag.html">Configuring I/O Tags</a> </li> </ul> </li> <li> <a href="modbus_protocol.html">The Modbus Protocol</a> <ul> <li> <a href="modbus_recommended_site.html">Recommended Websites</a> </li> <li> <a href="modbus_supported_function.html">Supported Functions</a> </li> <li> <a href="modbus_special_function.html">Special Functions</a> </li> </ul> </li> <li> <a href="modbus_config.html">Configuration</a> <ul> <li> <a href="modbus_config_property.html">Properties</a> <ul> <li> <a href="modbus_config_property_modbus_tab.html">Modbus Tab</a> </li> <li> <a href="modbus_config_property_operations_tab.html">Operations Tab</a> <ul> <li> <a href="modbus_config_property_operations_tab_supported_datatype.html">Supported Data Types</a> <ul> <li> <a href="modbus_config_property_operations_tab_supported_datatype_gentime.html">GenTime Type</a> </li> <li> <a href="modbus_config_property_operations_tab_supported_datatype_user_defined.html">User-Defined Data Types</a> </li> </ul> </li> <li> <a href="modbus_config_property_operations_tab_import_export_operation.html">Importing and Exporting Operations</a> </li> </ul> </li> <li> <a href="modbus_config_property_gen_soe_tab.html">Gen SOE Tab</a> </li> <li> <a href="modbus_config_property_config_offline_mode.html">Offline Mode Configuration</a> </li> </ul> </li> <li> <a href="modbus_config_tag.html">Configuring Tags</a> <ul> <li> <a href="modbus_config_tag_io.html">Configuring an I/O Tag</a> <ul> <li> <a href="modbus_config_tagsio_string_parametrization.html">String Configuration</a> </li> <li> <a href="modbus_config_tagsio_numericconfig.html">Numerical Configuration</a> </li> <li> <a href="modbus_config_tag_io_tip_modbus_convention.html">Addressing Tips (Modbus Convention)</a> </li> <li> <a href="modbus_config_tag_io_automatic_block_partition.html">Automatic Block Partition</a> </li> <li> <a href="modbus_config_tag_io_superblock_reading.html">Superblock Reading (Grouping)</a> </li> </ul> </li> <li> <a href="modbus_config_tag_special.html">Configuring Special Tags</a> <ul> <li> <a href="modbus_config_tag_special_force_wait_silence.html">Forcing a Wait Silence</a> </li> <li> <a href="modbus_config_tag_special_reading_last_exception_code.html">Reading the Last Exception Code</a> </li> </ul> </li> </ul> </li> <li> <a href="modbus_config_mass_memory_reading.html">Mass Memory Reading</a> <ul> <li> <a href="modbus_config_mass_memory_reading_gepacrx7.html">Reading an Event Buffer from GE PAC RX7 Controllers</a> </li> <li> <a href="modbus_config_mass_memory_reading_sepam204080.html">Reading Events from Schneider Electric Relays from SEPAM 20, 40, and 80 Series</a> </li> <li> <a href="modbus_config_mass_memory_reading_generic_soe_algorithm.html">Elipse Software's Generic SOE Reading Algorithm</a> <ul> <li> <a href="modbus_config_mass_memory_reading_generic_soe_algorithm_event_table.html">Event Table</a> </li> <li> <a href="modbus_config_mass_memory_reading_generic_soe_algorithm_acquisition_plc.html">Acquisition Procedure in a PLC</a> </li> <li> <a href="modbus_config_mass_memory_reading_generic_soe_algorithm_acquisition_application.html">Acquisition Procedure in an Application</a> </li> </ul> </li> <li> <a href="modbus_config_mass_memory_reading_abbmge144.html">Reading Mass Memory Registers from ABB MGE 144 Meters</a> </li> </ul> </li> </ul> </li> <li> <a href="modbus_appendix.html">Appendix</a> <ul> <li> <a href="modbus_appendix_optimization_tip.html">Optimization Tips</a> </li> <li> <a href="modbus_appendix_faq.html">Frequently Asked Questions</a> </li> <li> <a href="modbus_appendix_device_list.html">List of Devices that Communicate with Modbus</a> </li> <li> <a href="modbus_appendix_default_exception_list.html">List of Protocol's Default Exceptions</a> </li> <li> <a href="modbus_appendix_max_limit_block_size.html">Maximum Limit for the Size of Blocks Supported by the Protocol</a> </li> <li> <a href="modbus_appendix_bcd_encoding.html">BCD Encoding</a> </li> </ul> </li> <li> <a href="modbus_iokit.html">Documentation of I/O Interfaces</a> <ul> <li> <a href="manual_config.html">Driver Configuration</a> <ul> <li> <a href="manual_config_iokit_dialog_box.html">Configuration Dialog Box</a> </li> <li> <a href="manual_config_setup.html">Setup Tab</a> </li> <li> <a href="manual_config_serial.html">Serial Tab</a> </li> <li> <a href="manual_config_ethernet.html">Ethernet Tab</a> </li> <li> <a href="manual_config_modem.html">Modem Tab</a> </li> <li> <a href="manual_config_ras.html">RAS Tab</a> </li> </ul> </li> <li> <a href="manual_general.html">General Configurations</a> <ul> <li> <a href="manual_general_iotag.html">I/O Tags</a> <ul> <li> <a href="manual_general_iotag_iokitevent.html">IO.IOKitEvent</a> </li> <li> <a href="manual_general_iotag_physicallayerstatus.html">IO.PhysicalLayerStatus</a> </li> <li> <a href="manual_general_iotag_setconfigurationparameters.html">IO.SetConfigurationParameters</a> </li> <li> <a href="manual_general_iotag_workonline.html">IO.WorkOnline</a> </li> </ul> </li> <li> <a href="manual_general_property.html">Properties</a> <ul> <li> <a href="manual_io_connectionmode.html">IO.ConnectionMode</a> </li> <li> <a href="manual_io_giveupenable.html">IO.GiveUpEnable</a> </li> <li> <a href="manual_io_giveuptries.html">IO.GiveUpTries</a> </li> <li> <a href="manual_io_inactivityenable.html">IO.InactivityEnable</a> </li> <li> <a href="manual_io_inactivityperiodsec.html">IO.InactivityPeriodSec</a> </li> <li> <a href="manual_io_recoverenable.html">IO.RecoverEnable</a> </li> <li> <a href="manual_io_recoverperiodsec.html">IO.RecoverPeriodSec</a> </li> <li> <a href="manual_io_startoffline.html">IO.StartOffline</a> </li> <li> <a href="manual_io_timeoutms.html">IO.TimeoutMs</a> </li> <li> <a href="manual_io_type.html">IO.Type</a> </li> </ul> </li> </ul> </li> <li> <a href="manual_stats.html">Statistical Configuration</a> <ul> <li> <a href="manual_stats_iotag.html">I/O Tags</a> <ul> <li> <a href="manual_stats_iotag_io_stats_partial_bytesrecv.html">IO.Stats.Partial.BytesRecv</a> </li> <li> <a href="manual_stats_iotag_io_stats_partial_bytessent.html">IO.Stats.Partial.BytesSent</a> </li> <li> <a href="manual_stats_iotag_io_stats_partial_timeconnectedseconds.html">IO.Stats.Partial.TimeConnectedSeconds</a> </li> <li> <a href="manual_stats_iotag_io_stats_partial_timedisconnectedseconds.html">IO.Stats.Partial.TimeDisconnectedSeconds</a> </li> <li> <a href="manual_stats_iotag_io_stats_total_bytesrecv.html">IO.Stats.Total.BytesRecv</a> </li> <li> <a href="manual_stats_iotag_io_stats_total_bytessent.html">IO.Stats.Total.BytesSent</a> </li> <li> <a href="manual_stats_iotag_io_stats_total_connectioncount.html">IO.Stats.Total.ConnectionCount</a> </li> <li> <a href="manual_stats_iotag_io_stats_total_timeconnectedseconds.html">IO.Stats.Total.TimeConnectedSeconds</a> </li> <li> <a href="manual_stats_iotag_io_stats_total_timedisconnectedseconds.html">IO.Stats.Total.TimeDisconnectedSeconds</a> </li> </ul> </li> <li> <a href="manual_stats_property.html">Properties</a> </li> </ul> </li> <li> <a href="manual_ethernet.html">Ethernet Interface Configuration</a> <ul> <li> <a href="manual_ethernet_iotag.html">I/O Tags</a> <ul> <li> <a href="manual_ethernet_iotag_ipselect.html">IO.Ethernet.IPSelect</a> </li> <li> <a href="manual_ethernet_iotag_ipswitch.html">IO.Ethernet.IPSwitch</a> </li> </ul> </li> <li> <a href="manual_ethernet_property.html">Properties</a> <ul> <li> <a href="manual_io_ethernet_acceptconnection.html">IO.Ethernet.AcceptConnection</a> </li> <li> <a href="manual_io_ethernet_backupenable.html">IO.Ethernet.BackupEnable</a> </li> <li> <a href="manual_io_ethernet_backupip.html">IO.Ethernet.BackupIP</a> </li> <li> <a href="manual_io_ethernet_backupport.html">IO.Ethernet.BackupPort</a> </li> <li> <a href="manual_io_ethernet_listenport.html">IO.Ethernet.ListenPort</a> </li> <li> <a href="manual_io_ethernet_mainip.html">IO.Ethernet.MainIP</a> </li> <li> <a href="manual_io_ethernet_mainport.html">IO.Ethernet.MainPort</a> </li> <li> <a href="manual_io_ethernet_pingenable.html">IO.Ethernet.PingEnable</a> </li> <li> <a href="manual_io_ethernet_pingtimeoutms.html">IO.Ethernet.PingTimeoutMs</a> </li> <li> <a href="manual_io_ethernet_pingtries.html">IO.Ethernet.PingTries</a> </li> <li> <a href="manual_io_ethernet_transport.html">IO.Ethernet.Transport</a> </li> </ul> </li> </ul> </li> <li> <a href="manual_tapi.html">Modem Interface Configuration</a> <ul> <li> <a href="manual_tapi_iotag.html">I/O Tags</a> <ul> <li> <a href="manual_tapi_iotag_connectionbaudrate.html">IO.TAPI.ConnectionBaudRate</a> </li> <li> <a href="manual_tapi_iotag_dial.html">IO.TAPI.Dial</a> </li> <li> <a href="manual_tapi_iotag_hangup.html">IO.TAPI.HangUp</a> </li> <li> <a href="manual_tapi_iotag_ismodemconnected.html">IO.TAPI.IsModemConnected</a> </li> <li> <a href="manual_tapi_iotag_ismodemconnecting.html">IO.TAPI.IsModemConnecting</a> </li> <li> <a href="manual_tapi_iotag_modemstatus.html">IO.TAPI.ModemStatus</a> </li> <li> <a href="manual_tapi_iotag_phonenumber.html">IO.TAPI.PhoneNumber</a> </li> </ul> </li> <li> <a href="manual_tapi_property.html">Properties</a> <ul> <li> <a href="manual_io_tapi_acceptincoming.html">IO.TAPI.AcceptIncoming</a> </li> <li> <a href="manual_io_tapi_modemid.html">IO.TAPI.ModemID</a> </li> <li> <a href="manual_io_tapi_phonenumber.html">IO.TAPI.PhoneNumber</a> </li> </ul> </li> </ul> </li> <li> <a href="manual_ras.html">RAS Interface Configuration</a> <ul> <li> <a href="manual_ras_iotag.html">I/O Tags</a> </li> <li> <a href="manual_ras_property.html">Properties</a> <ul> <li> <a href="manual_io_ras_atcommand.html">IO.RAS.ATCommand</a> </li> <li> <a href="manual_io_ras_commandtimeoutsec.html">IO.RAS.CommandTimeoutSec</a> </li> </ul> </li> </ul> </li> <li> <a href="manual_serial.html">Serial Interface Configuration</a> <ul> <li> <a href="manual_serial_iotag.html">I/O Tags</a> </li> <li> <a href="manual_serial_property.html">Properties</a> <ul> <li> <a href="manual_io_serial_baudrate.html">IO.Serial.Baudrate</a> </li> <li> <a href="manual_io_serial_ctstimeoutms.html">IO.Serial.CTSTimeoutMs</a> </li> <li> <a href="manual_io_serial_databits.html">IO.Serial.DataBits</a> </li> <li> <a href="manual_io_serial_delayafterms.html">IO.Serial.DelayAfterMs</a> </li> <li> <a href="manual_io_serial_delaybeforems.html">IO.Serial.DelayBeforeMs</a> </li> <li> <a href="manual_io_serial_dtr.html">IO.Serial.DTR</a> </li> <li> <a href="manual_io_serial_interbytedelayus.html">IO.Serial.InterbyteDelayUs</a> </li> <li> <a href="manual_io_serial_interframedelayms.html">IO.Serial.InterframeDelayMs</a> </li> <li> <a href="manual_io_serial_parity.html">IO.Serial.Parity</a> </li> <li> <a href="manual_io_serial_port.html">IO.Serial.Port</a> </li> <li> <a href="manual_io_serial_rts.html">IO.Serial.RTS</a> </li> <li> <a href="manual_io_serial_stopbits.html">IO.Serial.StopBits</a> </li> <li> <a href="manual_io_serial_supressecho.html">IO.Serial.SupressEcho</a> </li> <li> <a href="manual_io_serial_waitcts.html">IO.Serial.WaitCTS</a> </li> </ul> </li> </ul> </li> </ul> </li> <li> <a href="modbus_driver_revision_history.html">Driver Revision History</a> </li> </ul> </div> </div> </div> </nav> <!-- Section <section> <header class="major"> <h2>Ante interdum</h2> </header> <div class="mini-posts"> <article> <a href="#" class="image"><img src="images/pic07.jpg" alt="" /></a> <p>Aenean ornare velit lacus, ac varius enim lorem ullamcorper dolore aliquam.</p> </article> <article> <a href="#" class="image"><img src="images/pic08.jpg" alt="" /></a> <p>Aenean ornare velit lacus, ac varius enim lorem ullamcorper dolore aliquam.</p> </article> <article> <a href="#" class="image"><img src="images/pic09.jpg" alt="" /></a> <p>Aenean ornare velit lacus, ac varius enim lorem ullamcorper dolore aliquam.</p> </article> </div> <ul class="actions"> <li><a href="#" class="button">More</a></li> </ul> </section> --> <!-- Section --> <section> <header class="major"> <h2>Get in touch</h2> </header> <p>Submit feedback about this site to:</p> <ul class="contact"> <li class="fa-envelope-o"><a href="mailto:helpdocs@rehmann.co">helpdocs@rehmann.co</a></li> </ul> </section> <!-- Footer --> <footer id="footer"> <p class="copyright">© <a href="https://documentation.help">documentation.help</a>. Design: <a href="https://rehmann.co">rehmann.co</a>.</p> <ul class="icons"> <!-- <li><a href="https://twitter.com/ca_carb" class="icon fa-twitter"><span class="label">Twitter</span></a></li> <li><a href="http://fb.me/carbparts" class="icon fa-facebook"><span class="label">Facebook</span></a></li> <li><a href="#" class="icon fa-instagram"><span class="label">Instagram</span></a></li>--> </ul> </footer> </div> </div> </div> <!-- Scripts --> <script src="/assets/js/jquery.min.js"></script> <script src="/assets/js/skel.min.js"></script> <script src="/assets/js/util.js"></script> <!--[if lte IE 8]><script src="assets/js/ie/respond.min.js"></script><![endif]--> <script src="/assets/js/main.js"></script> </body> </html> <script src="/cdn-cgi/scripts/7d0fa10a/cloudflare-static/rocket-loader.min.js" data-cf-settings="9a22b3ce181b04e2f1f78765-\|49" defer></script>