X-CUBE-SPN7 for X-NUCLEO-IHM07M1: C:/Users/giuseppe scuderi-sl/Desktop/MOTOR CONTROL/Peppe/trunk/Firmware/X-CUBE-SPN7-MC-6STEP/Projects/Multi/Examples/MotorControl/Inc/stm32f0xx_hal_conf.h File Reference

X-NUCLEO-IHM07M1 X-CUBE-SPN7

stm32f0xx_hal_conf.h File Reference

HAL configuration file. More...

#include "stm32f0xx_hal_rcc.h" #include "stm32f0xx_hal_gpio.h"
#include "stm32f0xx_hal_dma.h"
#include "stm32f0xx_hal_cortex.h"
#include "stm32f0xx_hal_adc.h"
#include "stm32f0xx_hal_crc.h"
#include "stm32f0xx_hal_flash.h"
#include "stm32f0xx_hal_pwr.h"
#include "stm32f0xx_hal_tim.h"
#include "stm32f0xx_hal_uart.h"
Include dependency graph for stm32f0xx_hal_conf.h:

Go to the source code of this file.

Macros

#define HAL_MODULE_ENABLED
 This is the list of modules to be used in the HAL driver.
 
#define HAL_ADC_MODULE_ENABLED
 
#define HAL_CRC_MODULE_ENABLED
 
#define HAL_TIM_MODULE_ENABLED
 
#define HAL_UART_MODULE_ENABLED
 
#define HAL_CORTEX_MODULE_ENABLED
 
#define HAL_DMA_MODULE_ENABLED
 
#define HAL_FLASH_MODULE_ENABLED
 
#define HAL_GPIO_MODULE_ENABLED
 
#define HAL_PWR_MODULE_ENABLED
 
#define HAL_RCC_MODULE_ENABLED
 
#define HSE_VALUE   ((uint32_t)8000000)
 Adjust the value of External High Speed oscillator (HSE) used in your application. This value is used by the RCC HAL module to compute the system frequency (when HSE is used as system clock source, directly or through the PLL). More...
 
#define HSE_STARTUP_TIMEOUT   ((uint32_t)5000)
 In the following line adjust the External High Speed oscillator (HSE) Startup Timeout value. More...
 
#define HSI_VALUE   ((uint32_t)8000000)
 Internal High Speed oscillator (HSI) value. This value is used by the RCC HAL module to compute the system frequency (when HSI is used as system clock source, directly or through the PLL). More...
 
#define HSI_STARTUP_TIMEOUT   ((uint32_t)5000)
 In the following line adjust the Internal High Speed oscillator (HSI) Startup Timeout value. More...
 
#define HSI14_VALUE   ((uint32_t)14000000)
 Internal High Speed oscillator for ADC (HSI14) value. More...
 
#define HSI48_VALUE   ((uint32_t)48000000)
 Internal High Speed oscillator for USB (HSI48) value. More...
 
#define LSI_VALUE   ((uint32_t)40000)
 Internal Low Speed oscillator (LSI) value.
 
#define LSE_VALUE   ((uint32_t)32768)
 External Low Speed oscillator (LSI) value. More...
 
#define VDD_VALUE   ((uint32_t)3300)
 This is the HAL system configuration section. More...
 
#define TICK_INT_PRIORITY   ((uint32_t)2)
 
#define USE_RTOS   0
 
#define PREFETCH_ENABLE   1
 
#define INSTRUCTION_CACHE_ENABLE   0
 
#define DATA_CACHE_ENABLE   0
 
#define assert_param(expr)   ((void)0)
 Uncomment the line below to expanse the "assert_param" macro in the HAL drivers code. More...
 

Detailed Description

HAL configuration file.

Attention

© COPYRIGHT(c) 2015 STMicroelectronics

Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:

  1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
  2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
  3. Neither the name of STMicroelectronics nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission.

THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

Macro Definition Documentation

#define assert_param (   expr)    ((void)0)

Uncomment the line below to expanse the "assert_param" macro in the HAL drivers code.

Include module's header file

#define HSE_STARTUP_TIMEOUT   ((uint32_t)5000)

In the following line adjust the External High Speed oscillator (HSE) Startup Timeout value.

Time out for HSE start up, in ms

#define HSE_VALUE   ((uint32_t)8000000)

Adjust the value of External High Speed oscillator (HSE) used in your application. This value is used by the RCC HAL module to compute the system frequency (when HSE is used as system clock source, directly or through the PLL).

Value of the External oscillator in Hz

#define HSI14_VALUE   ((uint32_t)14000000)

Internal High Speed oscillator for ADC (HSI14) value.

Value of the Internal High Speed oscillator for ADC in Hz. The real value may vary depending on the variations in voltage and temperature.

#define HSI48_VALUE   ((uint32_t)48000000)

Internal High Speed oscillator for USB (HSI48) value.

Value of the Internal High Speed oscillator for USB in Hz. The real value may vary depending on the variations in voltage and temperature.

#define HSI_STARTUP_TIMEOUT   ((uint32_t)5000)

In the following line adjust the Internal High Speed oscillator (HSI) Startup Timeout value.

Time out for HSI start up

#define HSI_VALUE   ((uint32_t)8000000)

Internal High Speed oscillator (HSI) value. This value is used by the RCC HAL module to compute the system frequency (when HSI is used as system clock source, directly or through the PLL).

Value of the Internal oscillator in Hz

#define LSE_VALUE   ((uint32_t)32768)

External Low Speed oscillator (LSI) value.

< Value of the Internal Low Speed oscillator in Hz The real value may vary depending on the variations in voltage and temperature. Value of the External Low Speed oscillator in Hz

#define TICK_INT_PRIORITY   ((uint32_t)2)

tick interrupt priority (lowest by default)

#define VDD_VALUE   ((uint32_t)3300)

This is the HAL system configuration section.

Value of VDD in mv

Generated on Fri Sep 11 2015 16:47:21 for X-CUBE-SPN7 for X-NUCLEO-IHM07M1 by   doxygen 1.8.9.1