stm3210e_eval.c File Reference

This file provides a set of firmware functions to manage Leds, push-button and COM ports for STM3210E_EVAL. More...

#include "stm3210e_eval.h"

Go to the source code of this file.

Data Structures
struct	LCD_CONTROLLER_TypeDef
Defines
#define	__STM3210E_EVAL_BSP_VERSION_MAIN   (0x06)
	STM3210E EVAL BSP Driver version number.
#define	__STM3210E_EVAL_BSP_VERSION_SUB1   (0x00)
#define	__STM3210E_EVAL_BSP_VERSION_SUB2   (0x02)
#define	__STM3210E_EVAL_BSP_VERSION_RC   (0x00)
#define	__STM3210E_EVAL_BSP_VERSION
#define	TFT_LCD_BASE   FSMC_BANK1_4
#define	TFT_LCD   ((LCD_CONTROLLER_TypeDef *) TFT_LCD_BASE)
Functions
static void	FSMC_BANK1NORSRAM4_WriteData (uint16_t Data)
	Writes register value.
static void	FSMC_BANK1NORSRAM4_WriteReg (uint8_t Reg)
	Writes register address.
static uint16_t	FSMC_BANK1NORSRAM4_ReadData (uint8_t Reg)
	Reads register value.
static void	FSMC_BANK1NORSRAM4_Init (void)
	Initializes LCD IO.
static void	FSMC_BANK1NORSRAM4_MspInit (void)
	Initializes FSMC_BANK4 MSP.
void	LCD_IO_Init (void)
	Initializes LCD low level.
void	LCD_IO_WriteData (uint16_t RegValue)
	Writes data on LCD data register.
void	LCD_IO_WriteMultipleData (uint8_t *pData, uint32_t Size)
	Writes multiple data on LCD data register.
void	LCD_IO_WriteReg (uint8_t Reg)
	Writes register on LCD register.
uint16_t	LCD_IO_ReadData (uint16_t Reg)
	Reads data from LCD data register.
void	LCD_Delay (uint32_t Delay)
	Wait for loop in ms.
static void	I2Cx_Init (void)
	Eval I2Cx Bus initialization.
static void	I2Cx_WriteData (uint16_t Addr, uint8_t Reg, uint8_t Value)
	Write a value in a register of the device through BUS.
static HAL_StatusTypeDef	I2Cx_WriteBuffer (uint16_t Addr, uint8_t Reg, uint16_t RegSize, uint8_t *pBuffer, uint16_t Length)
	Write a value in a register of the device through BUS.
static uint8_t	I2Cx_ReadData (uint16_t Addr, uint8_t Reg)
	Read a value in a register of the device through BUS.
static HAL_StatusTypeDef	I2Cx_ReadBuffer (uint16_t Addr, uint8_t Reg, uint16_t RegSize, uint8_t *pBuffer, uint16_t Length)
	Reads multiple data on the BUS.
static HAL_StatusTypeDef	I2Cx_IsDeviceReady (uint16_t DevAddress, uint32_t Trials)
	Checks if target device is ready for communication.
static void	I2Cx_Error (void)
	Eval I2Cx error treatment function.
static void	I2Cx_MspInit (I2C_HandleTypeDef *hi2c)
	Eval I2Cx MSP Initialization.
void	TSENSOR_IO_Init (void)
	Initializes peripherals used by the I2C Temperature Sensor driver.
void	TSENSOR_IO_Write (uint16_t DevAddress, uint8_t *pBuffer, uint8_t WriteAddr, uint16_t Length)
	Writes one byte to the TSENSOR.
void	TSENSOR_IO_Read (uint16_t DevAddress, uint8_t *pBuffer, uint8_t ReadAddr, uint16_t Length)
	Reads one byte from the TSENSOR.
uint16_t	TSENSOR_IO_IsDeviceReady (uint16_t DevAddress, uint32_t Trials)
	Checks if Temperature Sensor is ready for communication.
void	AUDIO_IO_Init (void)
	Initializes Audio low level.
void	AUDIO_IO_DeInit (void)
	DeInitializes Audio low level.
void	AUDIO_IO_Write (uint8_t Addr, uint8_t Reg, uint8_t Value)
	Writes a single data.
uint8_t	AUDIO_IO_Read (uint8_t Addr, uint8_t Reg)
	Reads a single data.
static HAL_StatusTypeDef	SPIx_Init (void)
	Initializes SPI HAL.
static uint8_t	SPIx_Write (uint8_t WriteValue)
	SPI Write a byte to device.
static uint8_t	SPIx_Read (void)
	SPI Read 1 byte from device.
static void	SPIx_Error (void)
	SPI error treatment function.
static void	SPIx_MspInit (SPI_HandleTypeDef *hspi)
	Initializes SPI MSP.
HAL_StatusTypeDef	FLASH_SPI_IO_Init (void)
	Initializes the FLASH SPI and put it into StandBy State (Ready for data transfer).
uint8_t	FLASH_SPI_IO_WriteByte (uint8_t Data)
	Write a byte on the FLASH SPI.
uint8_t	FLASH_SPI_IO_ReadByte (void)
	Read a byte from the FLASH SPI.
HAL_StatusTypeDef	FLASH_SPI_IO_ReadData (uint32_t MemAddress, uint8_t *pBuffer, uint32_t BufferSize)
	Read data from FLASH SPI driver.
void	FLASH_SPI_IO_WriteEnable (void)
	Select the FLASH SPI and send "Write Enable" instruction.
HAL_StatusTypeDef	FLASH_SPI_IO_WaitForWriteEnd (void)
	Wait response from the FLASH SPI and Deselect the device.
uint32_t	FLASH_SPI_IO_ReadID (void)
	Reads FLASH SPI identification.
uint32_t	BSP_GetVersion (void)
	This method returns the STM3210E EVAL BSP Driver revision.
void	BSP_LED_Init (Led_TypeDef Led)
	Configures LED GPIO.
void	BSP_LED_On (Led_TypeDef Led)
	Turns selected LED On.
void	BSP_LED_Off (Led_TypeDef Led)
	Turns selected LED Off.
void	BSP_LED_Toggle (Led_TypeDef Led)
	Toggles the selected LED.
void	BSP_PB_Init (Button_TypeDef Button, ButtonMode_TypeDef Button_Mode)
	Configures push button GPIO and EXTI Line.
uint32_t	BSP_PB_GetState (Button_TypeDef Button)
	Returns the selected button state.
uint8_t	BSP_JOY_Init (JOYMode_TypeDef Joy_Mode)
	Configures all button of the joystick in GPIO or EXTI modes.
JOYState_TypeDef	BSP_JOY_GetState (void)
	Returns the current joystick status.
void	BSP_COM_Init (COM_TypeDef COM, UART_HandleTypeDef *huart)
	Configures COM port.
Variables
GPIO_TypeDef *	LED_PORT [LEDn]
	LED variables.
const uint16_t	LED_PIN [LEDn]
GPIO_TypeDef *	BUTTON_PORT [BUTTONn]
	BUTTON variables.
const uint16_t	BUTTON_PIN [BUTTONn]
const uint8_t	BUTTON_IRQn [BUTTONn]
GPIO_TypeDef *	JOY_PORT [JOYn]
	JOYSTICK variables.
const uint16_t	JOY_PIN [JOYn]
const uint8_t	JOY_IRQn [JOYn]
USART_TypeDef *	COM_USART [COMn] = {EVAL_COM1, EVAL_COM2}
	COM variables.
GPIO_TypeDef *	COM_TX_PORT [COMn] = {EVAL_COM1_TX_GPIO_PORT, EVAL_COM2_TX_GPIO_PORT}
GPIO_TypeDef *	COM_RX_PORT [COMn] = {EVAL_COM1_RX_GPIO_PORT, EVAL_COM2_RX_GPIO_PORT}
const uint16_t	COM_TX_PIN [COMn] = {EVAL_COM1_TX_PIN, EVAL_COM2_TX_PIN}
const uint16_t	COM_RX_PIN [COMn] = {EVAL_COM1_RX_PIN, EVAL_COM2_RX_PIN}
uint32_t	SpixTimeout = EVAL_SPIx_TIMEOUT_MAX
	BUS variables.
static SPI_HandleTypeDef	heval_Spi
uint32_t	I2cxTimeout = EVAL_I2Cx_TIMEOUT_MAX
I2C_HandleTypeDef	heval_I2c

---

Detailed Description

This file provides a set of firmware functions to manage Leds, push-button and COM ports for STM3210E_EVAL.

Author:

MCD Application Team

Version:

V6.0.2

Date:

29-April-2016

Attention:

© COPYRIGHT(c) 2016 STMicroelectronics

Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. 2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. 3. Neither the name of STMicroelectronics nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission.

THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

Definition in file stm3210e_eval.c.