stm32h743i_eval_eeprom.c File Reference

This file provides a set of functions needed to manage an I2C M24LR64 EEPROM memory. More...

#include "stm32h743i_eval_eeprom.h"

Go to the source code of this file.

Functions
uint32_t	BSP_EEPROM_Init (void)
	Initializes peripherals used by the I2C EEPROM driver.
uint8_t	BSP_EEPROM_DeInit (void)
	DeInitializes the EEPROM.
uint32_t	BSP_EEPROM_ReadBuffer (uint8_t *pBuffer, uint16_t ReadAddr, uint16_t *NumByteToRead)
	Reads a block of data from the EEPROM.
uint32_t	BSP_EEPROM_WritePage (uint8_t *pBuffer, uint16_t WriteAddr, uint8_t *NumByteToWrite)
	Writes more than one byte to the EEPROM with a single WRITE cycle.
uint32_t	BSP_EEPROM_WriteBuffer (uint8_t *pBuffer, uint16_t WriteAddr, uint16_t NumByteToWrite)
	Writes buffer of data to the I2C EEPROM.
uint32_t	BSP_EEPROM_WaitEepromStandbyState (void)
	Wait for EEPROM Standby state.
__weak void	BSP_EEPROM_TIMEOUT_UserCallback (void)
	Basic management of the timeout situation.
Variables
__IO uint16_t	EEPROMAddress = 0
__IO uint16_t	EEPROMDataRead
__IO uint8_t	EEPROMDataWrite

---

Detailed Description

This file provides a set of functions needed to manage an I2C M24LR64 EEPROM memory.

Author:

MCD Application Team

Version:

V1.0.0

Date:

21-April-2017

            To be able to use this driver, the switch EE_M24LR64 must be defined
            in your toolchain compiler preprocessor

            ===================================================================
            Notes:
             - The I2C EEPROM memory (M24LR64) is available on separate daughter
               board ANT7-M24LR-A, which is not provided with the STM32H743I_EVAL
               board.
               To use this driver you have to connect the ANT7-M24LR-A to CN2
               connector of STM32H743I_EVAL board.
            ===================================================================

            It implements a high level communication layer for read and write
            from/to this memory. The needed STM32H7xx hardware resources (I2C and
            GPIO) are defined in stm32h743i_eval.h file, and the initialization is
            performed in EEPROM_IO_Init() function declared in stm32h743i_eval.c
            file.
            You can easily tailor this driver to any other development board,
            by just adapting the defines for hardware resources and
            EEPROM_IO_Init() function.

            @note In this driver, basic read and write functions (BSP_EEPROM_ReadBuffer()
                  and BSP_EEPROM_WritePage()) use DMA mode to perform the data
                  transfer to/from EEPROM memory.

           @note   Regarding BSP_EEPROM_WritePage(), it is an optimized function to perform
                  small write (less than 1 page) BUT the number of bytes (combined to write start address) must not
                  cross the EEPROM page boundary. This function can only writes into
                  the boundaries of an EEPROM page.
                  This function doesn't check on boundaries condition (in this driver
                  the function BSP_EEPROM_WriteBuffer() which calls BSP_EEPROM_WritePage() is
                  responsible of checking on Page boundaries).


       +-----------------------------------------------------------------+
       |               Pin assignment for M24LR64 EEPROM                 |
       +---------------------------------------+-----------+-------------+
       |  STM32H7xx I2C Pins                   |   EEPROM  |   Pin       |
       +---------------------------------------+-----------+-------------+
       | .                                     |   E0(GND) |    1  (0V)  |
       | .                                     |   AC0     |    2        |
       | .                                     |   AC1     |    3        |
       | .                                     |   VSS     |    4  (0V)  |
       | SDA                                   |   SDA     |    5        |
       | SCL                                   |   SCL     |    6        |
       | .                                     |   E1(GND) |    7  (0V)  |
       | .                                     |   VDD     |    8 (3.3V) |
       +---------------------------------------+-----------+-------------+
  

Attention:

© COPYRIGHT(c) 2017 STMicroelectronics

Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. 2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. 3. Neither the name of STMicroelectronics nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission.

THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

Definition in file stm32h743i_eval_eeprom.c.