STM32H743I_EVAL BSP User Manual: stm32h743i_eval.h File Reference

STM32H743I_EVAL BSP

stm32h743i_eval.h File Reference

This file contains definitions for STM32H743I_EVAL LEDs, push-buttons and COM ports hardware resources. More...

#include "stm32h7xx_hal.h"

Go to the source code of this file.

Defines

#define LEDn   ((uint8_t)2)
#define LED1_GPIO_PORT   GPIOF
#define LED1_GPIO_CLK_ENABLE()   __HAL_RCC_GPIOF_CLK_ENABLE()
#define LED1_GPIO_CLK_DISABLE()   __HAL_RCC_GPIOF_CLK_DISABLE()
#define LED1_PIN   GPIO_PIN_10
#define LED3_GPIO_PORT   GPIOA
#define LED3_GPIO_CLK_ENABLE()   __HAL_RCC_GPIOA_CLK_ENABLE()
#define LED3_GPIO_CLK_DISABLE()   __HAL_RCC_GPIOA_CLK_DISABLE()
#define LED3_PIN   GPIO_PIN_4
#define MFX_IRQOUT_PIN   GPIO_PIN_8
 MFX_IRQOUt pin.
#define MFX_IRQOUT_GPIO_PORT   GPIOI
#define MFX_IRQOUT_GPIO_CLK_ENABLE()   __HAL_RCC_GPIOI_CLK_ENABLE()
#define MFX_IRQOUT_GPIO_CLK_DISABLE()   __HAL_RCC_GPIOI_CLK_DISABLE()
#define MFX_IRQOUT_EXTI_IRQn   EXTI9_5_IRQn
#define BUTTONn   ((uint8_t)3)
#define WAKEUP_BUTTON_PIN   GPIO_PIN_0
 Wakeup push-button.
#define WAKEUP_BUTTON_GPIO_PORT   GPIOA
#define WAKEUP_BUTTON_GPIO_CLK_ENABLE()   __HAL_RCC_GPIOA_CLK_ENABLE()
#define WAKEUP_BUTTON_GPIO_CLK_DISABLE()   __HAL_RCC_GPIOA_CLK_DISABLE()
#define WAKEUP_BUTTON_EXTI_IRQn   EXTI0_IRQn
#define TAMPER_BUTTON_PIN   GPIO_PIN_13
 Tamper push-button.
#define TAMPER_BUTTON_GPIO_PORT   GPIOC
#define TAMPER_BUTTON_GPIO_CLK_ENABLE()   __HAL_RCC_GPIOC_CLK_ENABLE()
#define TAMPER_BUTTON_GPIO_CLK_DISABLE()   __HAL_RCC_GPIOC_CLK_DISABLE()
#define TAMPER_BUTTON_EXTI_IRQn   EXTI15_10_IRQn
#define KEY_BUTTON_PIN   GPIO_PIN_13
 Key push-button.
#define KEY_BUTTON_GPIO_PORT   GPIOC
#define KEY_BUTTON_GPIO_CLK_ENABLE()   __HAL_RCC_GPIOC_CLK_ENABLE()
#define KEY_BUTTON_GPIO_CLK_DISABLE()   __HAL_RCC_GPIOC_CLK_DISABLE()
#define KEY_BUTTON_EXTI_IRQn   EXTI15_10_IRQn
#define BUTTONx_GPIO_CLK_ENABLE(__INDEX__)
#define BUTTONx_GPIO_CLK_DISABLE(__INDEX__)
#define COMn   ((uint8_t)1)
#define EVAL_COM1   USART1
 Definition for COM port1, connected to USART1.
#define EVAL_COM1_CLK_ENABLE()   __HAL_RCC_USART1_CLK_ENABLE()
#define EVAL_COM1_CLK_DISABLE()   __HAL_RCC_USART1_CLK_DISABLE()
#define EVAL_COM1_TX_PIN   GPIO_PIN_14
#define EVAL_COM1_TX_GPIO_PORT   GPIOB
#define EVAL_COM1_TX_GPIO_CLK_ENABLE()   __HAL_RCC_GPIOB_CLK_ENABLE()
#define EVAL_COM1_TX_GPIO_CLK_DISABLE()   __HAL_RCC_GPIOB_CLK_DISABLE()
#define EVAL_COM1_TX_AF   GPIO_AF4_USART1
#define EVAL_COM1_RX_PIN   GPIO_PIN_15
#define EVAL_COM1_RX_GPIO_PORT   GPIOB
#define EVAL_COM1_RX_GPIO_CLK_ENABLE()   __HAL_RCC_GPIOB_CLK_ENABLE()
#define EVAL_COM1_RX_GPIO_CLK_DISABLE()   __HAL_RCC_GPIOB_CLK_DISABLE()
#define EVAL_COM1_RX_AF   GPIO_AF4_USART1
#define EVAL_COM1_IRQn   USART1_IRQn
#define EVAL_COMx_CLK_ENABLE(__INDEX__)   do { if((__INDEX__) == COM1) EVAL_COM1_CLK_ENABLE(); } while(0)
#define EVAL_COMx_CLK_DISABLE(__INDEX__)   (((__INDEX__) == 0) ? EVAL_COM1_CLK_DISABLE() : 0)
#define EVAL_COMx_TX_GPIO_CLK_ENABLE(__INDEX__)   do { if((__INDEX__) == COM1) EVAL_COM1_TX_GPIO_CLK_ENABLE(); } while(0)
#define EVAL_COMx_TX_GPIO_CLK_DISABLE(__INDEX__)   (((__INDEX__) == 0) ? EVAL_COM1_TX_GPIO_CLK_DISABLE() : 0)
#define EVAL_COMx_RX_GPIO_CLK_ENABLE(__INDEX__)   do { if((__INDEX__) == COM1) EVAL_COM1_RX_GPIO_CLK_ENABLE(); } while(0)
#define EVAL_COMx_RX_GPIO_CLK_DISABLE(__INDEX__)   (((__INDEX__) == 0) ? EVAL_COM1_RX_GPIO_CLK_DISABLE() : 0)
#define ADCx   ADC1
 Definition for Potentiometer, connected to ADC1.
#define ADCx_CLK_ENABLE()   __HAL_RCC_ADC12_CLK_ENABLE()
#define ADCx_CHANNEL_GPIO_CLK_ENABLE()   __HAL_RCC_GPIOA_CLK_ENABLE()
#define ADCx_FORCE_RESET()   __HAL_RCC_ADC12_FORCE_RESET()
#define ADCx_RELEASE_RESET()   __HAL_RCC_ADC12_RELEASE_RESET()
#define ADCx_CHANNEL_PIN   GPIO_PIN_0
#define ADCx_CHANNEL_GPIO_PORT   GPIOA
#define ADCx_CHANNEL   ADC_CHANNEL_0
#define ADCx_POLL_TIMEOUT   10
#define IO_I2C_ADDRESS   ((uint16_t)0x84) /*mfx MFX_I2C_ADDR 0*/
#define IO_I2C_ADDRESS_2   ((uint16_t)0x86) /*mfx MFX_I2C_ADDR 1*/
#define TS_I2C_ADDRESS   ((uint16_t)0x82) /*stmpe811 used on MB1046 board */
#define TS3510_I2C_ADDRESS   ((uint16_t)0x80)
#define EXC7200_I2C_ADDRESS   ((uint16_t)0x08)
#define AUDIO_I2C_ADDRESS   ((uint16_t)0x34)
#define EEPROM_I2C_ADDRESS_A01   ((uint16_t)0xA0)
#define EEPROM_I2C_ADDRESS_A02   ((uint16_t)0xA6)
#define EVAL_I2Cx   I2C1
#define EVAL_I2Cx_CLK_ENABLE()   __HAL_RCC_I2C1_CLK_ENABLE()
#define EVAL_DMAx_CLK_ENABLE()   __HAL_RCC_DMA1_CLK_ENABLE()
#define EVAL_I2Cx_SCL_SDA_GPIO_CLK_ENABLE()   __HAL_RCC_GPIOB_CLK_ENABLE()
#define EVAL_I2Cx_FORCE_RESET()   __HAL_RCC_I2C1_FORCE_RESET()
#define EVAL_I2Cx_RELEASE_RESET()   __HAL_RCC_I2C1_RELEASE_RESET()
#define EVAL_I2Cx_SCL_PIN   GPIO_PIN_6
#define EVAL_I2Cx_SCL_SDA_GPIO_PORT   GPIOB
#define EVAL_I2Cx_SCL_SDA_AF   GPIO_AF4_I2C1
#define EVAL_I2Cx_SDA_PIN   GPIO_PIN_7
#define EVAL_I2Cx_EV_IRQn   I2C1_EV_IRQn
#define EVAL_I2Cx_ER_IRQn   I2C1_ER_IRQn
#define LCD_TIMx   TIM3
 Definition for LCD Timer used to control the Brightnes.
#define LCD_TIMx_CLK_ENABLE()   __HAL_RCC_TIM3_CLK_ENABLE()
#define LCD_TIMx_CLK_DISABLE()   __HAL_RCC_TIM3_CLK_DISABLE()
#define LCD_TIMx_CHANNEL   TIM_CHANNEL_1
#define LCD_TIMx_CHANNEL_AF   GPIO_AF2_TIM3
#define LCD_TIMX_PERIOD_VALUE   ((uint32_t)50000) /* Period Value */
#define LCD_TIMX_PRESCALER_VALUE   ((uint32_t)4) /* Prescaler Value */

Enumerations

enum  Led_TypeDef { LED1 = 0, LED_GREEN = LED1, LED3 = 1, LED_RED = LED3 }
enum  Button_TypeDef { BUTTON_WAKEUP = 0, BUTTON_TAMPER = 1, BUTTON_KEY = 2 }
enum  ButtonMode_TypeDef { BUTTON_MODE_GPIO = 0, BUTTON_MODE_EXTI = 1 }
enum  COM_TypeDef { COM1 = 0, COM2 = 1 }

Functions

uint32_t BSP_GetVersion (void)
 This method returns the STM32H743I EVAL BSP Driver revision.
void BSP_LED_Init (Led_TypeDef Led)
 Configures LED on GPIO and/or on MFX.
void BSP_LED_DeInit (Led_TypeDef Led)
 DeInit LEDs.
void BSP_LED_On (Led_TypeDef Led)
 Turns selected LED On.
void BSP_LED_Off (Led_TypeDef Led)
 Turns selected LED Off.
void BSP_LED_Toggle (Led_TypeDef Led)
 Toggles the selected LED.
void BSP_PB_Init (Button_TypeDef Button, ButtonMode_TypeDef ButtonMode)
 Configures button GPIO and EXTI Line.
void BSP_PB_DeInit (Button_TypeDef Button)
 Push Button DeInit.
uint32_t BSP_PB_GetState (Button_TypeDef Button)
 Returns the selected button state.
void BSP_COM_Init (COM_TypeDef COM, UART_HandleTypeDef *huart)
 Configures COM port.
void BSP_COM_DeInit (COM_TypeDef COM, UART_HandleTypeDef *huart)
 DeInit COM port.
void BSP_POTENTIOMETER_Init (void)
 Init Potentiometer.
uint32_t BSP_POTENTIOMETER_GetLevel (void)
 Get Potentiometer level in 12 bits.

Detailed Description

This file contains definitions for STM32H743I_EVAL LEDs, push-buttons and COM ports hardware resources.

Author:
MCD Application Team
Version:
V1.0.0
Date:
21-April-2017
Attention:

© COPYRIGHT(c) 2017 STMicroelectronics

Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. 2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. 3. Neither the name of STMicroelectronics nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission.

THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

Definition in file stm32h743i_eval.h.

Generated on Wed Aug 23 2017 17:45:13 for STM32H743I_EVAL BSP User Manual by   doxygen 1.7.6.1