Frequency
| Power
| Source
Ports| #
Points | Trigger
:Ext
Sweep settings:..Time
| Setup
| Segment
| Power |
New See Remotely Specifying a Source Port .
Description |
SCPI |
|
|---|---|---|
Start Freq |
|
|
Stop Freq |
|
|
Center Freq |
|
|
Span |
|
|
CW Frequency |
|
|
Number of Points |
|
|
Step size |
|
|
Power Settings See Remotely Specifying a Source Port . |
|
Power ON | OFF |
|
Source Power (Auto | ON | OFF) |
|
Power Value |
|
Port Selection |
|
Couple Ports OFF | ON |
|
Attenuator Mode Auto|Manual |
|
Attenuation Value |
|
Power Slope ON | OFF |
|
Power Slope Value |
|
Set power limit |
|
Power limit ON/OFF |
|
Power limit UI lock |
|
Specifying Source Ports See Remotely Specifying a Source Port. |
|
Returns the number of source ports. |
None |
Returns the string names of source ports. |
|
Returns the source port number of the specified string port name. |
None |
IF Bandwidth |
|
Previous IF Bandwidth |
None |
Next IFBandwidth |
None |
Reduce IF BW |
|
Sweep Time Value |
|
Number of Points |
|
Sweep Type (Lin | Pwr | CW | Seg | Phase) |
|
Sweep Generation (Stepped | Analog) |
|
Dwell Time Value |
|
Dwell Time Auto set the minimum dwell time |
|
Sweep Delay |
|
Alternate Sweeps |
|
External ALC |
|
Enable Point Sweep |
|
Fast Sweep |
|
Fast CW |
|
Start Power |
|
Stop Power |
|
Center |
|
Span |
|
ON|OFF |
|
Add a segment |
|
Delete a segment |
|
Delete all segments |
|
Count the segments |
|
Read the segment number |
None |
Segment Center Frequency |
|
Segment Frequency Span |
|
Segment Start Frequency |
|
Segment Stop Frequency |
|
Number of Points |
|
IF Bandwidth |
|
IF Bandwidth Option |
|
Source Power |
|
Source Power Option |
|
X-Axis Point Spacing |
|
Allow Arbitrary Segments |
|
Upload a segment table |
|
Download a segment table |
|
|
Source (where trigger comes from) |
|
Source (Int | Ext | Manual) |
|
Internal | Manual |
|
Trigger! (for Manual Source) |
|
Scope (what is triggered) |
|
Scope (Global | Channel) |
|
Channel Settings (how the channel responds to triggers) |
|
Continuous |
|
Read Continuous Mode |
None |
Number of Groups |
|
Read Groups |
None |
Hold |
|
Hold Mode (read-only) |
None |
All channels in Hold |
|
All channels Resume |
|
Single |
|
Trigger Mode (Channel | Point | Sweep) |
|
Restart |
|
Abort |
|
Scope (Global/Chan) |
|
Trigger Delay (Global) |
|
Trigger Delay (Channel) |
|
MeasTrigIn/ Hand I/O |
|
Level or Edge |
|
Neg/Low or Pos/High |
|
Ready for Trigger Indicator (Out) |
|
MeasTrig Rdy/ Hand I/O |
|
High / Low |
|
Which AuxTrig connector pair being used. |
N/A |
How many Aux connector pairs. |
|
AUX TRIG OUT |
|
Enable |
|
Global or Channel Pref. |
|
Polarity (Pos/Neg) |
|
Position (Before/After acq) |
|
OUT Pulse width |
|
Point or Sweep. |
|
AUX TRIG (Ready) IN |
|
Enable Handshake |
|
Edge or Level Level NOT in UI. |
|
Polarity High/leading or Low/trailing. |
|
Delay |
|
