Functions
uint8_t	BSP_SD_Init (void)
	Initializes the SD/SD communication.
uint8_t	BSP_SD_IsDetected (void)
	Detects if SD card is correctly plugged in the memory slot or not.
uint8_t	BSP_SD_ReadBlocks (uint32_t *p32Data, uint64_t ReadAddr, uint16_t BlockSize, uint32_t NumberOfBlocks)
	Reads block(s) from a specified address in an SD card, in polling mode.
uint8_t	BSP_SD_WriteBlocks (uint32_t *p32Data, uint64_t WriteAddr, uint16_t BlockSize, uint32_t NumberOfBlocks)
	Writes block(s) to a specified address in an SD card, in polling mode.
uint8_t	BSP_SD_Erase (uint32_t StartAddr, uint32_t EndAddr)
	Erases the specified memory area of the given SD card.
uint8_t	BSP_SD_GetStatus (void)
	Returns the SD status.
uint8_t	BSP_SD_GetCardInfo (SD_CardInfo *pCardInfo)
	Returns information about specific card.
void	SD_IO_Init (void)
	Initializes the SD Card and put it into StandBy State (Ready for data transfer).
void	SD_IO_WriteByte (uint8_t Data)
	Writes a byte on the SD.
uint8_t	SD_IO_ReadByte (void)
	Reads a byte from the SD.
HAL_StatusTypeDef	SD_IO_WriteCmd (uint8_t Cmd, uint32_t Arg, uint8_t Crc, uint8_t Response)
	Sends 5 bytes command to the SD card and get response.
HAL_StatusTypeDef	SD_IO_WaitResponse (uint8_t Response)
	Waits response from the SD card.
void	SD_IO_WriteDummy (void)
	Sends dummy byte with CS High.

Function Documentation

uint8_t BSP_SD_Erase	(	uint32_t	StartAddr,
		uint32_t	EndAddr
	)

Erases the specified memory area of the given SD card.

Parameters:

StartAddr	Start byte address
EndAddr	End byte address

Return values:

SD status

Definition at line 664 of file stm32303e_eval_sd.c.

References MSD_ERROR, MSD_OK, SD_CMD_ERASE, SD_CMD_SD_ERASE_GRP_END, SD_CMD_SD_ERASE_GRP_START, SD_IO_WaitResponse(), SD_RESPONSE_NO_ERROR, and SD_SendCmd().

uint8_t BSP_SD_GetCardInfo ( SD_CardInfo * pCardInfo )

Returns information about specific card.

Parameters:

pCardInfo pointer to a SD_CardInfo structure that contains all SD card information.

Return values:

The	SD Response: MSD_ERROR : Sequence failed MSD_OK : Sequence succeed

Definition at line 197 of file stm32303e_eval_sd.c.

References SD_CardInfo::CardBlockSize, SD_CardInfo::CardCapacity, SD_CardInfo::Cid, SD_CardInfo::Csd, SD_CSD::DeviceSize, SD_CSD::DeviceSizeMul, MSD_ERROR, SD_CSD::RdBlockLen, SD_GetCIDRegister(), and SD_GetCSDRegister().

uint8_t BSP_SD_GetStatus ( void )

Returns the SD status.

Return values:

The	SD status.

Definition at line 632 of file stm32303e_eval_sd.c.

References MSD_OK.

uint8_t BSP_SD_Init ( void )

Initializes the SD/SD communication.

Return values:

The	SD Response: MSD_ERROR : Sequence failed MSD_OK : Sequence succeed

Definition at line 152 of file stm32303e_eval_sd.c.

References BSP_SD_IsDetected(), MSD_ERROR, SD_GoIdleState(), SD_IO_Init(), SD_NOT_PRESENT, SD_PRESENT, and SdStatus.

uint8_t BSP_SD_IsDetected ( void )

Detects if SD card is correctly plugged in the memory slot or not.

Return values:

Returns if SD is detected or not

Definition at line 176 of file stm32303e_eval_sd.c.

References SD_DETECT_GPIO_PORT, SD_DETECT_PIN, SD_NOT_PRESENT, and SD_PRESENT.

Referenced by BSP_SD_Init().

uint8_t BSP_SD_ReadBlocks	(	uint32_t *	p32Data,
		uint64_t	ReadAddr,
		uint16_t	BlockSize,
		uint32_t	NumberOfBlocks
	)

Reads block(s) from a specified address in an SD card, in polling mode.

Parameters:

p32Data	Pointer to the buffer that will contain the data to transmit
ReadAddr	Address from where data is to be read
BlockSize	SD card data block size, that should be 512
NumberOfBlocks	Number of SD blocks to read

Return values:

SD status

Definition at line 220 of file stm32303e_eval_sd.c.

References MSD_ERROR, MSD_OK, SD_CMD_READ_SINGLE_BLOCK, SD_CMD_SET_BLOCKLEN, SD_IO_ReadByte(), SD_IO_WaitResponse(), SD_IO_WriteCmd(), SD_IO_WriteDummy(), SD_RESPONSE_NO_ERROR, and SD_START_DATA_SINGLE_BLOCK_READ.

uint8_t BSP_SD_WriteBlocks	(	uint32_t *	p32Data,
		uint64_t	WriteAddr,
		uint16_t	BlockSize,
		uint32_t	NumberOfBlocks
	)

Writes block(s) to a specified address in an SD card, in polling mode.

Parameters:

p32Data	Pointer to the buffer that will contain the data to transmit
WriteAddr	Address from where data is to be written
BlockSize	SD card data block size, that should be 512
NumberOfBlocks	Number of SD blocks to write

Return values:

SD status

Definition at line 286 of file stm32303e_eval_sd.c.

References MSD_ERROR, MSD_OK, SD_CMD_WRITE_SINGLE_BLOCK, SD_DATA_OK, SD_DUMMY_BYTE, SD_GetDataResponse(), SD_IO_ReadByte(), SD_IO_WriteByte(), SD_IO_WriteCmd(), SD_IO_WriteDummy(), SD_RESPONSE_NO_ERROR, and SD_START_DATA_SINGLE_BLOCK_WRITE.