stm32l152d_eval.h File Reference

This file contains definitions for STM32L152D_EVAL's LEDs, push-buttons and COM ports hardware resources. More...

#include "stm32l1xx_hal.h"

Go to the source code of this file.

Defines
#define	LEDn   4
#define	LED1_PIN   GPIO_PIN_3 /* PD.03*/
#define	LED1_GPIO_PORT   GPIOD
#define	LED1_GPIO_CLK_ENABLE()   __HAL_RCC_GPIOD_CLK_ENABLE()
#define	LED1_GPIO_CLK_DISABLE()   __HAL_RCC_GPIOD_CLK_DISABLE()
#define	LED2_PIN   GPIO_PIN_7 /* PD.07*/
#define	LED2_GPIO_PORT   GPIOD
#define	LED2_GPIO_CLK_ENABLE()   __HAL_RCC_GPIOD_CLK_ENABLE()
#define	LED2_GPIO_CLK_DISABLE()   __HAL_RCC_GPIOD_CLK_DISABLE()
#define	LED3_PIN   GPIO_PIN_14 /* PG.14*/
#define	LED3_GPIO_PORT   GPIOG
#define	LED3_GPIO_CLK_ENABLE()   __HAL_RCC_GPIOG_CLK_ENABLE()
#define	LED3_GPIO_CLK_DISABLE()   __HAL_RCC_GPIOG_CLK_DISABLE()
#define	LED4_PIN   GPIO_PIN_15 /* PG.15*/
#define	LED4_GPIO_PORT   GPIOG
#define	LED4_GPIO_CLK_ENABLE()   __HAL_RCC_GPIOG_CLK_ENABLE()
#define	LED4_GPIO_CLK_DISABLE()   __HAL_RCC_GPIOG_CLK_DISABLE()
#define	LEDx_GPIO_CLK_ENABLE(__LED__)
#define	LEDx_GPIO_CLK_DISABLE(__LED__)
#define	JOYn   5
#define	BUTTONn   1 + JOYn
#define	TAMPER_BUTTON_PIN   GPIO_PIN_0 /* PA.00*/
	Key push-button.
#define	TAMPER_BUTTON_GPIO_PORT   GPIOA
#define	TAMPER_BUTTON_GPIO_CLK_ENABLE()   __HAL_RCC_GPIOA_CLK_ENABLE()
#define	TAMPER_BUTTON_GPIO_CLK_DISABLE()   __HAL_RCC_GPIOA_CLK_DISABLE()
#define	TAMPER_BUTTON_EXTI_IRQn   EXTI0_IRQn
#define	RIGHT_JOY_PIN   GPIO_PIN_7 /* PG.07*/
	Joystick Right push-button.
#define	RIGHT_JOY_GPIO_PORT   GPIOG
#define	RIGHT_JOY_GPIO_CLK_ENABLE()   __HAL_RCC_GPIOG_CLK_ENABLE()
#define	RIGHT_JOY_GPIO_CLK_DISABLE()   __HAL_RCC_GPIOG_CLK_DISABLE()
#define	RIGHT_JOY_EXTI_IRQn   EXTI9_5_IRQn
#define	LEFT_JOY_PIN   GPIO_PIN_6 /* PG.06*/
	Joystick Left push-button.
#define	LEFT_JOY_GPIO_PORT   GPIOG
#define	LEFT_JOY_GPIO_CLK_ENABLE()   __HAL_RCC_GPIOG_CLK_ENABLE()
#define	LEFT_JOY_GPIO_CLK_DISABLE()   __HAL_RCC_GPIOG_CLK_DISABLE()
#define	LEFT_JOY_EXTI_IRQn   EXTI9_5_IRQn
#define	UP_JOY_PIN   GPIO_PIN_11 /* PG.11*/
	Joystick Up push-button.
#define	UP_JOY_GPIO_PORT   GPIOG
#define	UP_JOY_GPIO_CLK_ENABLE()   __HAL_RCC_GPIOG_CLK_ENABLE()
#define	UP_JOY_GPIO_CLK_DISABLE()   __HAL_RCC_GPIOG_CLK_DISABLE()
#define	UP_JOY_EXTI_IRQn   EXTI15_10_IRQn
#define	DOWN_JOY_PIN   GPIO_PIN_8 /* PG.08*/
	Joystick Down push-button.
#define	DOWN_JOY_GPIO_PORT   GPIOG
#define	DOWN_JOY_GPIO_CLK_ENABLE()   __HAL_RCC_GPIOG_CLK_ENABLE()
#define	DOWN_JOY_GPIO_CLK_DISABLE()   __HAL_RCC_GPIOG_CLK_DISABLE()
#define	DOWN_JOY_EXTI_IRQn   EXTI9_5_IRQn
#define	SEL_JOY_PIN   GPIO_PIN_13 /* PG.13*/
	Joystick Sel push-button.
#define	SEL_JOY_GPIO_PORT   GPIOG
#define	SEL_JOY_GPIO_CLK_ENABLE()   __HAL_RCC_GPIOG_CLK_ENABLE()
#define	SEL_JOY_GPIO_CLK_DISABLE()   __HAL_RCC_GPIOG_CLK_DISABLE()
#define	SEL_JOY_EXTI_IRQn   EXTI15_10_IRQn
#define	BUTTONx_GPIO_CLK_ENABLE(__BUTTON__)
#define	BUTTONx_GPIO_CLK_DISABLE(__BUTTON__)
#define	JOYx_GPIO_CLK_ENABLE(__JOY__)
#define	JOYx_GPIO_CLK_DISABLE(__JOY__)
#define	COMn   1
#define	EVAL_COM1   USART1
	Definition for COM port1, connected to USART1.
#define	EVAL_COM1_CLK_ENABLE()   __HAL_RCC_USART1_CLK_ENABLE()
#define	EVAL_COM1_CLK_DISABLE()   __HAL_RCC_USART1_CLK_DISABLE()
#define	EVAL_COM1_TX_PIN   GPIO_PIN_9 /* PA.09*/
#define	EVAL_COM1_TX_GPIO_PORT   GPIOA
#define	EVAL_COM1_TX_GPIO_CLK_ENABLE()   __HAL_RCC_GPIOA_CLK_ENABLE()
#define	EVAL_COM1_TX_GPIO_CLK_DISABLE()   __HAL_RCC_GPIOA_CLK_DISABLE()
#define	EVAL_COM1_TX_AF   GPIO_AF7_USART1
#define	EVAL_COM1_RX_PIN   GPIO_PIN_10 /* PA.10*/
#define	EVAL_COM1_RX_GPIO_PORT   GPIOA
#define	EVAL_COM1_RX_GPIO_CLK_ENABLE()   __HAL_RCC_GPIOA_CLK_ENABLE()
#define	EVAL_COM1_RX_GPIO_CLK_DISABLE()   __HAL_RCC_GPIOA_CLK_DISABLE()
#define	EVAL_COM1_RX_AF   GPIO_AF7_USART1
#define	EVAL_COM1_IRQn   USART1_IRQn
#define	COMx_CLK_ENABLE(__INDEX__)   do { if((__INDEX__) == COM1) EVAL_COM1_CLK_ENABLE();} while(0)
#define	COMx_CLK_DISABLE(__INDEX__)   (((__INDEX__) == COM1) ? EVAL_COM1_CLK_DISABLE() : 0)
#define	COMx_TX_GPIO_CLK_ENABLE(__INDEX__)   do { if((__INDEX__) == COM1) EVAL_COM1_TX_GPIO_CLK_ENABLE();} while(0)
#define	COMx_TX_GPIO_CLK_DISABLE(__INDEX__)   (((__INDEX__) == COM1) ? EVAL_COM1_TX_GPIO_CLK_DISABLE() : 0)
#define	COMx_RX_GPIO_CLK_ENABLE(__INDEX__)   do { if((__INDEX__) == COM1) EVAL_COM1_RX_GPIO_CLK_ENABLE();} while(0)
#define	COMx_RX_GPIO_CLK_DISABLE(__INDEX__)   (((__INDEX__) == COM1) ? EVAL_COM1_RX_GPIO_CLK_DISABLE() : 0)
#define	EVAL_I2Cx_SCL_PIN   GPIO_PIN_8 /* PB.08*/
#define	EVAL_I2Cx_SCL_GPIO_PORT   GPIOB
#define	EVAL_I2Cx_SDA_PIN   GPIO_PIN_9 /* PB.09*/
#define	EVAL_I2Cx_SDA_GPIO_PORT   GPIOB
#define	EVAL_I2Cx_SCL_SDA_AF   GPIO_AF4_I2C1
#define	EVAL_I2Cx   I2C1
#define	EVAL_I2Cx_CLK_ENABLE()   __HAL_RCC_I2C1_CLK_ENABLE()
#define	EVAL_I2Cx_SDA_GPIO_CLK_ENABLE()   __HAL_RCC_GPIOB_CLK_ENABLE()
#define	EVAL_I2Cx_SCL_GPIO_CLK_ENABLE()   __HAL_RCC_GPIOB_CLK_ENABLE()
#define	EVAL_I2Cx_FORCE_RESET()   __HAL_RCC_I2C1_FORCE_RESET()
#define	EVAL_I2Cx_RELEASE_RESET()   __HAL_RCC_I2C1_RELEASE_RESET()
#define	EVAL_I2Cx_EV_IRQn   I2C1_EV_IRQn
#define	EVAL_I2Cx_EV_IRQHandler   I2C1_EV_IRQHandler
#define	EVAL_I2Cx_ER_IRQn   I2C1_ER_IRQn
#define	EVAL_I2Cx_ER_IRQHandler   I2C1_ER_IRQHandler
#define	EVAL_I2Cx_TIMEOUT_MAX   3000
#define	EVAL_SPIx   SPI1
#define	EVAL_SPIx_CLK_ENABLE()   __HAL_RCC_SPI1_CLK_ENABLE()
#define	EVAL_SPIx_SCK_AF   GPIO_AF5_SPI1
#define	EVAL_SPIx_SCK_GPIO_PORT   GPIOA /* PA.05*/
#define	EVAL_SPIx_SCK_PIN   GPIO_PIN_5
#define	EVAL_SPIx_SCK_GPIO_CLK_ENABLE()   __HAL_RCC_GPIOA_CLK_ENABLE()
#define	EVAL_SPIx_SCK_GPIO_CLK_DISABLE()   __HAL_RCC_GPIOA_CLK_DISABLE()
#define	EVAL_SPIx_MISO_MOSI_AF   GPIO_AF5_SPI1
#define	EVAL_SPIx_MISO_MOSI_GPIO_PORT   GPIOE
#define	EVAL_SPIx_MISO_MOSI_GPIO_CLK_ENABLE()   __HAL_RCC_GPIOE_CLK_ENABLE()
#define	EVAL_SPIx_MISO_MOSI_GPIO_CLK_DISABLE()   __HAL_RCC_GPIOE_CLK_DISABLE()
#define	EVAL_SPIx_MISO_PIN   GPIO_PIN_14 /* PE.14*/
#define	EVAL_SPIx_MOSI_PIN   GPIO_PIN_15 /* PE.15*/
#define	EVAL_SPIx_TIMEOUT_MAX   1000
#define	EEPROM_CS_LOW()   HAL_GPIO_WritePin(EEPROM_CS_GPIO_PORT, EEPROM_CS_PIN, GPIO_PIN_RESET)
#define	EEPROM_CS_HIGH()   HAL_GPIO_WritePin(EEPROM_CS_GPIO_PORT, EEPROM_CS_PIN, GPIO_PIN_SET)
#define	EEPROM_CS_PIN   GPIO_PIN_5 /* PC.05*/
	EEPROM Control Interface pins.
#define	EEPROM_CS_GPIO_PORT   GPIOC
#define	EEPROM_CS_GPIO_CLK_ENABLE()   __HAL_RCC_GPIOC_CLK_ENABLE()
#define	EEPROM_CS_GPIO_CLK_DISABLE()   __HAL_RCC_GPIOC_CLK_DISABLE()
#define	AUDIO_I2C_ADDRESS   0x94
	AUDIO I2C Interface pins.
#define	AUDIO_RESET_GPIO_CLK_ENABLE()   __HAL_RCC_GPIOB_CLK_ENABLE()
#define	AUDIO_RESET_PIN   GPIO_PIN_1 /* PB.01*/
#define	AUDIO_RESET_GPIO   GPIOB
Enumerations
enum	Led_TypeDef {   LED1 = 0, LED2 = 1, LED3 = 2, LED4 = 3,   LED_GREEN = LED1, LED_ORANGE = LED2, LED_RED = LED3, LED_BLUE = LED4 }
	LED Types Definition. More...
enum	Button_TypeDef {   BUTTON_TAMPER = 0, BUTTON_SEL = 1, BUTTON_LEFT = 2, BUTTON_RIGHT = 3,   BUTTON_DOWN = 4, BUTTON_UP = 5, BUTTON_KEY = BUTTON_TAMPER }
	BUTTON Types Definition. More...
enum	ButtonMode_TypeDef { BUTTON_MODE_GPIO = 0, BUTTON_MODE_EXTI = 1 }
enum	JOYState_TypeDef {   JOY_SEL = 0, JOY_LEFT = 1, JOY_RIGHT = 2, JOY_DOWN = 3,   JOY_UP = 4, JOY_NONE = 5 }
	JOYSTICK Types Definition. More...
enum	JOYMode_TypeDef { JOY_MODE_GPIO = 0, JOY_MODE_EXTI = 1 }
enum	COM_TypeDef { COM1 = 0 }
	COM Types Definition. More...
Functions
uint32_t	BSP_GetVersion (void)
	This method returns the STM32L152D EVAL BSP Driver revision.
void	BSP_LED_Init (Led_TypeDef Led)
	Configures LED GPIO.
void	BSP_LED_On (Led_TypeDef Led)
	Turns selected LED On.
void	BSP_LED_Off (Led_TypeDef Led)
	Turns selected LED Off.
void	BSP_LED_Toggle (Led_TypeDef Led)
	Toggles the selected LED.
void	BSP_PB_Init (Button_TypeDef Button, ButtonMode_TypeDef Button_Mode)
	Configures push button GPIO and EXTI Line.
uint32_t	BSP_PB_GetState (Button_TypeDef Button)
	Returns the selected button state.
void	BSP_COM_Init (COM_TypeDef COM, UART_HandleTypeDef *huart)
	Configures COM port.
uint8_t	BSP_JOY_Init (JOYMode_TypeDef Joy_Mode)
	Configures all button of the joystick in GPIO or EXTI modes.
JOYState_TypeDef	BSP_JOY_GetState (void)
	Returns the current joystick status.

---

Detailed Description

This file contains definitions for STM32L152D_EVAL's LEDs, push-buttons and COM ports hardware resources.

Author:

MCD Application Team

Attention:

© COPYRIGHT(c) 2017 STMicroelectronics

Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. 2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. 3. Neither the name of STMicroelectronics nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission.

THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

Definition in file stm32l152d_eval.h.