|
STM32L152D_EVAL BSP User Manual
|
This file contains the common defines and functions prototypes for the stm32l152d_eval_nor.c driver. More...
#include "stm32l1xx_hal.h"
Go to the source code of this file.
Defines | |
| #define | NOR_STATUS_OK 0x00 |
| NOR status structure definition. | |
| #define | NOR_STATUS_ERROR 0x01 |
| #define | NOR_DEVICE_ADDR ((uint32_t)0x64000000) |
| #define | NOR_MEMORY_WIDTH FSMC_NORSRAM_MEM_BUS_WIDTH_16 |
| #define | NOR_BURSTACCESS FSMC_BURST_ACCESS_MODE_DISABLE |
| #define | NOR_WRITEBURST FSMC_WRITE_BURST_DISABLE |
| #define | BLOCKERASE_TIMEOUT ((uint32_t)0x00A00000) /* NOR block erase timeout */ |
| #define | CHIPERASE_TIMEOUT ((uint32_t)0x30000000) /* NOR chip erase timeout */ |
| #define | PROGRAM_TIMEOUT ((uint32_t)0x00004400) /* NOR program timeout */ |
| #define | NOR_READY_BUSY_PIN GPIO_PIN_6 |
| #define | NOR_READY_BUSY_GPIO GPIOD |
| #define | NOR_READY_STATE GPIO_PIN_SET |
| #define | NOR_BUSY_STATE GPIO_PIN_RESET |
Functions | |
| uint8_t | BSP_NOR_Init (void) |
| Initializes the NOR device. | |
| uint8_t | BSP_NOR_ReadData (uint32_t uwStartAddress, uint16_t *pData, uint32_t uwDataSize) |
| Reads an amount of data from the NOR device. | |
| uint8_t | BSP_NOR_WriteData (uint32_t uwStartAddress, uint16_t *pData, uint32_t uwDataSize) |
| Writes an amount of data to the NOR device. | |
| uint8_t | BSP_NOR_ProgramData (uint32_t uwStartAddress, uint16_t *pData, uint32_t uwDataSize) |
| Programs an amount of data to the NOR device. | |
| uint8_t | BSP_NOR_Erase_Block (uint32_t BlockAddress) |
| Erases the specified block of the NOR device. | |
| uint8_t | BSP_NOR_Erase_Chip (void) |
| Erases the entire NOR chip. | |
| uint8_t | BSP_NOR_Read_ID (NOR_IDTypeDef *pNOR_ID) |
| Reads NOR flash IDs. | |
| void | BSP_NOR_ReturnToReadMode (void) |
| Returns the NOR memory to read mode. | |
Detailed Description
This file contains the common defines and functions prototypes for the stm32l152d_eval_nor.c driver.
- Attention:
© COPYRIGHT(c) 2017 STMicroelectronics
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. 2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. 3. Neither the name of STMicroelectronics nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
Definition in file stm32l152d_eval_nor.h.
Generated on Thu Aug 24 2017 17:57:47 for STM32L152D_EVAL BSP User Manual by
1.7.6.1