STM32F2xx_Nucleo_144 BSP User Manual: STM32F2XX NUCLEO 144 LOW LEVEL Exported Functions

This method returns the STM32F2xx NUCLEO BSP Driver revision.

Return values:

version,:

0xXYZR (8bits for each decimal, R for RC)

Definition at line 179 of file stm32f2xx_nucleo_144.c.

References __STM32F2xx_NUCLEO_BSP_VERSION.

DeInit joystick GPIOs.

Note:

JOY DeInit does not disable the Mfx, just set the Mfx pins in Off mode

Definition at line 794 of file stm32f2xx_nucleo_144.c.

References ADCx_DeInit().

Returns the Joystick key pressed.

Note:

To know which Joystick key is pressed we need to detect the voltage level on each key output

• None : 3.3 V / 4095
• SEL : 1.055 V / 1308
• DOWN : 0.71 V / 88
• LEFT : 3.0 V / 3720
• RIGHT : 0.595 V / 737
• UP : 1.65 V / 2046

Return values:

JOYState_TypeDef,:

Code of the Joystick key pressed.

Definition at line 811 of file stm32f2xx_nucleo_144.c.

References hnucleo_Adc, JOY_DOWN, JOY_LEFT, JOY_NONE, JOY_RIGHT, JOY_SEL, and JOY_UP.

Configures joystick available on adafruit 1.8" TFT shield managed through ADC to detect motion.

Return values:

Joystickstatus

(0=> success, 1=> fail)

Definition at line 774 of file stm32f2xx_nucleo_144.c.

References ADCx_Init(), hnucleo_Adc, NUCLEO_ADCx_CHANNEL, and sConfig.

DeInit LEDs.

Parameters:

Led,:

LED to be de-init. This parameter can be one of the following values: LED1 LED2 LED3

Note:

Led DeInit does not disable the GPIO clock nor disable the Mfx

Definition at line 218 of file stm32f2xx_nucleo_144.c.

References GPIO_PIN, and GPIO_PORT.

Configures LED GPIO.

Parameters:

Led,:

Specifies the Led to be configured. This parameter can be one of following parameters: LED1 LED2 LED3

Definition at line 192 of file stm32f2xx_nucleo_144.c.

References GPIO_PIN, GPIO_PORT, and LEDx_GPIO_CLK_ENABLE.

Turns selected LED Off.

Parameters:

Led,:

Specifies the Led to be set off. This parameter can be one of following parameters: LED1 LED2 LED3

Definition at line 248 of file stm32f2xx_nucleo_144.c.

References GPIO_PIN, and GPIO_PORT.

Turns selected LED On.

Parameters:

Led,:

Specifies the Led to be set on. This parameter can be one of following parameters: LED2

Definition at line 235 of file stm32f2xx_nucleo_144.c.

References GPIO_PIN, and GPIO_PORT.

Toggles the selected LED.

Parameters:

Led,:

Specifies the Led to be toggled. This parameter can be one of following parameters: LED1 LED2 LED3

Definition at line 261 of file stm32f2xx_nucleo_144.c.

References GPIO_PIN, and GPIO_PORT.

Push Button DeInit.

Parameters:

Button,:

Button to be configured This parameter should be: BUTTON_USER

Note:

PB DeInit does not disable the GPIO clock

Definition at line 313 of file stm32f2xx_nucleo_144.c.

References BUTTON_IRQn, BUTTON_PIN, and BUTTON_PORT.

Returns the selected Button state.

Parameters:

Button,:

Specifies the Button to be checked. This parameter should be: BUTTON_USER

Return values:

The	Button GPIO pin value.

Definition at line 328 of file stm32f2xx_nucleo_144.c.

References BUTTON_PIN, and BUTTON_PORT.

Configures Button GPIO and EXTI Line.

Parameters:

Button,:	Specifies the Button to be configured. This parameter should be: BUTTON_USER
ButtonMode,:	Specifies Button mode. This parameter can be one of following parameters: BUTTON_MODE_GPIO: Button will be used as simple IO BUTTON_MODE_EXTI: Button will be connected to EXTI line with interrupt generation capability

Definition at line 276 of file stm32f2xx_nucleo_144.c.

References BUTTON_IRQn, BUTTON_MODE_EXTI, BUTTON_MODE_GPIO, BUTTON_PIN, BUTTON_PORT, and BUTTONx_GPIO_CLK_ENABLE.