stm32f769i_eval.c File Reference

This file provides a set of firmware functions to manage LEDs, push-buttons and COM ports available on STM32F769I-EVAL evaluation board(MB1219) from STMicroelectronics. More...

#include "stm32f769i_eval.h"

Go to the source code of this file.

Defines
#define	__STM32F769I_EVAL_BSP_VERSION_MAIN   (0x02)
	STM32F769I EVAL BSP Driver version number V2.0.1.
#define	__STM32F769I_EVAL_BSP_VERSION_SUB1   (0x00)
#define	__STM32F769I_EVAL_BSP_VERSION_SUB2   (0x01)
#define	__STM32F769I_EVAL_BSP_VERSION_RC   (0x00)
#define	__STM32F769I_EVAL_BSP_VERSION
Functions
static void	I2Cx_MspInit (void)
	Initializes I2C MSP.
static void	I2Cx_Init (void)
	Initializes I2C HAL.
static void	I2Cx_Write (uint8_t Addr, uint8_t Reg, uint8_t Value)
	Writes a single data.
static uint8_t	I2Cx_Read (uint8_t Addr, uint8_t Reg)
	Reads a single data.
static HAL_StatusTypeDef	I2Cx_ReadMultiple (uint8_t Addr, uint16_t Reg, uint16_t MemAddress, uint8_t *Buffer, uint16_t Length)
	Reads multiple data.
static HAL_StatusTypeDef	I2Cx_WriteMultiple (uint8_t Addr, uint16_t Reg, uint16_t MemAddress, uint8_t *Buffer, uint16_t Length)
	Writes a value in a register of the device through BUS in using DMA mode.
static HAL_StatusTypeDef	I2Cx_IsDeviceReady (uint16_t DevAddress, uint32_t Trials)
	Checks if target device is ready for communication.
static void	I2Cx_Error (uint8_t Addr)
	Manages error callback by re-initializing I2C.
void	AUDIO_IO_Init (void)
	Initializes Audio low level.
void	AUDIO_IO_DeInit (void)
	Deinitializes Audio low level.
void	AUDIO_IO_Write (uint8_t Addr, uint16_t Reg, uint16_t Value)
	Writes a single data.
uint16_t	AUDIO_IO_Read (uint8_t Addr, uint16_t Reg)
	Reads a single data.
void	AUDIO_IO_Delay (uint32_t Delay)
	AUDIO Codec delay.
void	CAMERA_IO_Init (void)
	Initializes Camera low level.
void	CAMERA_Delay (uint32_t Delay)
	Camera delay.
void	CAMERA_IO_Write (uint8_t Addr, uint16_t Reg, uint16_t Value)
	Camera writes single data.
uint16_t	CAMERA_IO_Read (uint8_t Addr, uint16_t Reg)
	Camera reads single data.
void	EEPROM_IO_Init (void)
	Initializes peripherals used by the I2C EEPROM driver.
HAL_StatusTypeDef	EEPROM_IO_WriteData (uint16_t DevAddress, uint16_t MemAddress, uint8_t *pBuffer, uint32_t BufferSize)
	Write data to I2C EEPROM driver in using DMA channel.
HAL_StatusTypeDef	EEPROM_IO_ReadData (uint16_t DevAddress, uint16_t MemAddress, uint8_t *pBuffer, uint32_t BufferSize)
	Read data from I2C EEPROM driver in using DMA channel.
HAL_StatusTypeDef	EEPROM_IO_IsDeviceReady (uint16_t DevAddress, uint32_t Trials)
	Checks if target device is ready for communication.
void	TS_IO_Init (void)
	Initialize I2C communication channel from MCU to TouchScreen (TS).
void	TS_IO_Write (uint8_t Addr, uint8_t Reg, uint8_t Value)
	Writes single data with I2C communication channel from MCU to TouchScreen.
uint8_t	TS_IO_Read (uint8_t Addr, uint8_t Reg)
	Reads single data with I2C communication channel from TouchScreen.
uint16_t	TS_IO_ReadMultiple (uint8_t Addr, uint8_t Reg, uint8_t *Buffer, uint16_t Length)
	Reads multiple data with I2C communication channel from TouchScreen.
void	TS_IO_WriteMultiple (uint8_t Addr, uint8_t Reg, uint8_t *Buffer, uint16_t Length)
	Writes multiple data with I2C communication channel from MCU to TouchScreen.
void	TS_IO_Delay (uint32_t Delay)
	Delay function used in TouchScreen low level driver.
void	OTM8009A_IO_Delay (uint32_t Delay)
	OTM8009A delay.
uint32_t	BSP_GetVersion (void)
	This method returns the STM32F769I EVAL BSP Driver revision.
void	BSP_LED_Init (Led_TypeDef Led)
	Configures LED on GPIO and/or on MFX.
void	BSP_LED_DeInit (Led_TypeDef Led)
	DeInit LEDs.
void	BSP_LED_On (Led_TypeDef Led)
	Turns selected LED On.
void	BSP_LED_Off (Led_TypeDef Led)
	Turns selected LED Off.
void	BSP_LED_Toggle (Led_TypeDef Led)
	Toggles the selected LED.
void	BSP_PB_Init (Button_TypeDef Button, ButtonMode_TypeDef ButtonMode)
	Configures button GPIO and EXTI Line.
void	BSP_PB_DeInit (Button_TypeDef Button)
	Push Button DeInit.
uint32_t	BSP_PB_GetState (Button_TypeDef Button)
	Returns the selected button state.
void	BSP_COM_Init (COM_TypeDef COM, UART_HandleTypeDef *huart)
	Configures COM port.
void	BSP_COM_DeInit (COM_TypeDef COM, UART_HandleTypeDef *huart)
	DeInit COM port.
void	BSP_POTENTIOMETER_Init (void)
	Init Potentiometer.
uint32_t	BSP_POTENTIOMETER_GetLevel (void)
	Get Potentiometer level in 12 bits.
Variables
GPIO_TypeDef *	GPIO_PORT [LEDn]
const uint32_t	GPIO_PIN [LEDn]
GPIO_TypeDef *	BUTTON_PORT [BUTTONn]
const uint16_t	BUTTON_PIN [BUTTONn]
const uint16_t	BUTTON_IRQn [BUTTONn]
USART_TypeDef *	COM_USART [COMn] = {EVAL_COM1}
GPIO_TypeDef *	COM_TX_PORT [COMn] = {EVAL_COM1_TX_GPIO_PORT}
GPIO_TypeDef *	COM_RX_PORT [COMn] = {EVAL_COM1_RX_GPIO_PORT}
const uint16_t	COM_TX_PIN [COMn] = {EVAL_COM1_TX_PIN}
const uint16_t	COM_RX_PIN [COMn] = {EVAL_COM1_RX_PIN}
const uint16_t	COM_TX_AF [COMn] = {EVAL_COM1_TX_AF}
const uint16_t	COM_RX_AF [COMn] = {EVAL_COM1_RX_AF}
static I2C_HandleTypeDef	hEvalI2c
static ADC_HandleTypeDef	hEvalADC

---

Detailed Description

This file provides a set of firmware functions to manage LEDs, push-buttons and COM ports available on STM32F769I-EVAL evaluation board(MB1219) from STMicroelectronics.

Author:

MCD Application Team

            This driver requires the stm32f769i_eval_io.c/.h files to manage the 
            IO module resources mapped on the MFX IO expander.
            These resources are mainly LEDs, Joystick push buttons, SD detect pin, 
            USB OTG power switch/over current drive pins, Camera plug pin, Audio
            INT pin
  

Attention:

© COPYRIGHT(c) 2017 STMicroelectronics

Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. 2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. 3. Neither the name of STMicroelectronics nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission.

THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

Definition in file stm32f769i_eval.c.