|
STM3210E_EVAL BSP User Manual
|
This file contains the common defines and functions prototypes for the stm3210e_eval_flash driver. More...
#include "stm3210e_eval.h"
Go to the source code of this file.
Defines | |
| #define | FLASH_OK 0x00 |
| #define | FLASH_ERROR 0x01 |
Functions | |
| uint8_t | BSP_SERIAL_FLASH_Init (void) |
| Initializes peripherals used by the Serial FLASH device. | |
| uint8_t | BSP_SERIAL_FLASH_EraseSector (uint32_t SectorAddr) |
| Erases the specified FLASH sector. | |
| uint8_t | BSP_SERIAL_FLASH_EraseBulk (void) |
| Erases the entire FLASH. | |
| uint8_t | BSP_SERIAL_FLASH_WritePage (uint32_t uwStartAddress, uint8_t *pData, uint32_t uwDataSize) |
| Writes more than one byte to the FLASH with a single WRITE cycle (Page WRITE sequence). | |
| uint8_t | BSP_SERIAL_FLASH_WriteData (uint32_t uwStartAddress, uint8_t *pData, uint32_t uwDataSize) |
| Writes block of data to the FLASH. | |
| uint8_t | BSP_SERIAL_FLASH_ReadData (uint32_t uwStartAddress, uint8_t *pData, uint32_t uwDataSize) |
| Reads a block of data from the FLASH. | |
| uint32_t | BSP_SERIAL_FLASH_ReadID (void) |
| Reads FLASH identification. | |
| HAL_StatusTypeDef | FLASH_SPI_IO_Init (void) |
| Initializes the FLASH SPI and put it into StandBy State (Ready for data transfer). | |
| uint8_t | FLASH_SPI_IO_WriteByte (uint8_t Data) |
| Write a byte on the FLASH SPI. | |
| uint8_t | FLASH_SPI_IO_ReadByte (void) |
| Read a byte from the FLASH SPI. | |
| HAL_StatusTypeDef | FLASH_SPI_IO_ReadData (uint32_t MemAddress, uint8_t *pBuffer, uint32_t BufferSize) |
| Read data from FLASH SPI driver. | |
| void | FLASH_SPI_IO_WriteEnable (void) |
| Select the FLASH SPI and send "Write Enable" instruction. | |
| HAL_StatusTypeDef | FLASH_SPI_IO_WaitForWriteEnd (void) |
| Wait response from the FLASH SPI and Deselect the device. | |
| uint32_t | FLASH_SPI_IO_ReadID (void) |
| Reads FLASH SPI identification. | |
Detailed Description
This file contains the common defines and functions prototypes for the stm3210e_eval_flash driver.
- Attention:
© COPYRIGHT(c) 2015 STMicroelectronics
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. 2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. 3. Neither the name of STMicroelectronics nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
Definition in file stm3210e_eval_serialflash.h.
Generated on Thu Dec 10 2015 17:39:43 for STM3210E_EVAL BSP User Manual by
1.7.6.1