|
STM8S/A Standard Peripherals Drivers
|
This file contains all the functions/macros for the ADC1 peripheral. More...
#include "stm8s_adc1.h"
Go to the source code of this file.
Functions | |
| void | ADC1_AWDChannelConfig (ADC1_Channel_TypeDef Channel, FunctionalState NewState) |
| Enables or disables the analog watchdog for the given channel. | |
| void | ADC1_ClearFlag (ADC1_Flag_TypeDef Flag) |
| Clear the specified ADC1 Flag. | |
| void | ADC1_ClearITPendingBit (ADC1_IT_TypeDef ITPendingBit) |
| Clear the ADC1 End of Conversion pending bit. | |
| void | ADC1_Cmd (FunctionalState NewState) |
| Enables or Disables the ADC1 peripheral. | |
| void | ADC1_ConversionConfig (ADC1_ConvMode_TypeDef ADC1_ConversionMode, ADC1_Channel_TypeDef ADC1_Channel, ADC1_Align_TypeDef ADC1_Align) |
| Configure the ADC1 conversion on selected channel. | |
| void | ADC1_DataBufferCmd (FunctionalState NewState) |
| Enables or Disables the ADC1 data store into the Data Buffer registers rather than in the Data Register. | |
| void | ADC1_DeInit (void) |
| Deinitializes the ADC1 peripheral registers to their default reset values. | |
| void | ADC1_ExternalTriggerConfig (ADC1_ExtTrig_TypeDef ADC1_ExtTrigger, FunctionalState NewState) |
| Configure the ADC1 conversion on external trigger event. | |
| FlagStatus | ADC1_GetAWDChannelStatus (ADC1_Channel_TypeDef Channel) |
| Checks the specified analog watchdog channel status. | |
| uint16_t | ADC1_GetBufferValue (uint8_t Buffer) |
| Get one sample of measured signal. | |
| uint16_t | ADC1_GetConversionValue (void) |
| Get one sample of measured signal. | |
| FlagStatus | ADC1_GetFlagStatus (ADC1_Flag_TypeDef Flag) |
| Checks the specified ADC1 flag status. | |
| ITStatus | ADC1_GetITStatus (ADC1_IT_TypeDef ITPendingBit) |
| Returns the specified pending bit status. | |
| void | ADC1_Init (ADC1_ConvMode_TypeDef ADC1_ConversionMode, ADC1_Channel_TypeDef ADC1_Channel, ADC1_PresSel_TypeDef ADC1_PrescalerSelection, ADC1_ExtTrig_TypeDef ADC1_ExtTrigger, FunctionalState ADC1_ExtTriggerState, ADC1_Align_TypeDef ADC1_Align, ADC1_SchmittTrigg_TypeDef ADC1_SchmittTriggerChannel, FunctionalState ADC1_SchmittTriggerState) |
| Initializes the ADC1 peripheral according to the specified parameters. | |
| void | ADC1_ITConfig (ADC1_IT_TypeDef ADC1_IT, FunctionalState NewState) |
| Enables or disables the ADC1 interrupt. | |
| void | ADC1_PrescalerConfig (ADC1_PresSel_TypeDef ADC1_Prescaler) |
| Configure the ADC1 prescaler division factor. | |
| void | ADC1_ScanModeCmd (FunctionalState NewState) |
| Enables or Disables the ADC1 scan mode. | |
| void | ADC1_SchmittTriggerConfig (ADC1_SchmittTrigg_TypeDef ADC1_SchmittTriggerChannel, FunctionalState NewState) |
| Enables or disables the ADC1 Schmitt Trigger on a selected channel. | |
| void | ADC1_SetHighThreshold (uint16_t Threshold) |
| Sets the high threshold of the analog watchdog. | |
| void | ADC1_SetLowThreshold (uint16_t Threshold) |
| Sets the low threshold of the analog watchdog. | |
| void | ADC1_StartConversion (void) |
| Start ADC1 conversion. | |
Detailed Description
This file contains all the functions/macros for the ADC1 peripheral.
- Attention:
© COPYRIGHT 2014 STMicroelectronics
Licensed under MCD-ST Liberty SW License Agreement V2, (the "License"); You may not use this file except in compliance with the License. You may obtain a copy of the License at:
http://www.st.com/software_license_agreement_liberty_v2
Unless required by applicable law or agreed to in writing, software distributed under the License is distributed on an "AS IS" BASIS, WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the License for the specific language governing permissions and limitations under the License.
Definition in file stm8s_adc1.c.