STM32F4xx_Nucleo BSP User Manual: STM32F4XX NUCLEO LOW LEVEL Private Functions

STM32F4xx_Nucleo BSP Driver

STM32F4xx_Nucleo BSP User Manual
STM32F4XX NUCLEO LOW LEVEL Private Functions

Functions

uint32_t BSP_GetVersion (void)
 This method returns the STM32F4xx NUCLEO BSP Driver revision.
void BSP_LED_Init (Led_TypeDef Led)
 Configures LED GPIO.
void BSP_LED_DeInit (Led_TypeDef Led)
 DeInit LEDs.
void BSP_LED_On (Led_TypeDef Led)
 Turns selected LED On.
void BSP_LED_Off (Led_TypeDef Led)
 Turns selected LED Off.
void BSP_LED_Toggle (Led_TypeDef Led)
 Toggles the selected LED.
void BSP_PB_Init (Button_TypeDef Button, ButtonMode_TypeDef ButtonMode)
 Configures Button GPIO and EXTI Line.
void BSP_PB_DeInit (Button_TypeDef Button)
 Push Button DeInit.
uint32_t BSP_PB_GetState (Button_TypeDef Button)
 Returns the selected Button state.
uint8_t BSP_JOY_Init (void)
 Configures joystick available on adafruit 1.8" TFT shield managed through ADC to detect motion.
void BSP_JOY_DeInit (void)
 DeInit joystick GPIOs.
JOYState_TypeDef BSP_JOY_GetState (void)
 Returns the Joystick key pressed.
static void SPIx_WriteReadData (const uint8_t *DataIn, uint8_t *DataOut, uint16_t DataLegnth)
 SPI Write a byte to device.
static void SPIx_Write (uint8_t Value)
 SPI Write a byte to device.
void SD_IO_CSState (uint8_t val)
 Set the SD_CS pin.
void SD_IO_WriteReadData (const uint8_t *DataIn, uint8_t *DataOut, uint16_t DataLength)
 Write a byte on the SD.
uint8_t SD_IO_WriteByte (uint8_t Data)
 Writes a byte on the SD.
void LCD_IO_WriteReg (uint8_t LCDReg)
 Writes command to select the LCD register.
void LCD_IO_WriteData (uint8_t Data)
 Writes data to select the LCD register.
void LCD_IO_WriteMultipleData (uint8_t *pData, uint32_t Size)
 Writes register value.
void LCD_Delay (uint32_t Delay)
 Wait for loop in ms.
static void ADCx_MspDeInit (ADC_HandleTypeDef *hadc)
 DeInitializes ADC MSP.

Function Documentation

static void ADCx_MspDeInit ( ADC_HandleTypeDef *  hadc) [static]

DeInitializes ADC MSP.

Note:
ADC DeInit does not disable the GPIO clock

Definition at line 697 of file stm32f4xx_nucleo.c.

References NUCLEO_ADCx_CLK_DISABLE, NUCLEO_ADCx_GPIO_PIN, and NUCLEO_ADCx_GPIO_PORT.

Referenced by ADCx_DeInit().

uint32_t BSP_GetVersion ( void  )

This method returns the STM32F4xx NUCLEO BSP Driver revision.

Return values:
version,:0xXYZR (8bits for each decimal, R for RC)

Definition at line 179 of file stm32f4xx_nucleo.c.

References __STM32F4xx_NUCLEO_BSP_VERSION.

void BSP_JOY_DeInit ( void  )

DeInit joystick GPIOs.

Note:
JOY DeInit does not disable the Mfx, just set the Mfx pins in Off modee.

Definition at line 775 of file stm32f4xx_nucleo.c.

References ADCx_DeInit().

Returns the Joystick key pressed.

Note:
To know which Joystick key is pressed we need to detect the voltage level on each key output
  • None : 3.3 V / 4095
  • SEL : 1.055 V / 1308
  • DOWN : 0.71 V / 88
  • LEFT : 3.0 V / 3720
  • RIGHT : 0.595 V / 737
  • UP : 1.65 V / 2046
Return values:
JOYState_TypeDef,:Code of the Joystick key pressed.

Definition at line 792 of file stm32f4xx_nucleo.c.

References hnucleo_Adc, JOY_DOWN, JOY_LEFT, JOY_NONE, JOY_RIGHT, JOY_SEL, and JOY_UP.

uint8_t BSP_JOY_Init ( void  )

Configures joystick available on adafruit 1.8" TFT shield managed through ADC to detect motion.

Return values:
Joystickstatus(0=> success, 1=> fail)

Definition at line 755 of file stm32f4xx_nucleo.c.

References ADCx_Init(), hnucleo_Adc, NUCLEO_ADCx_CHANNEL, and sConfig.

void BSP_LED_DeInit ( Led_TypeDef  Led)

DeInit LEDs.

Parameters:
Led,:LED to be de-init. This parameter can be one of the following values:
  • LED2
Note:
Led DeInit does not disable the GPIO clock nor disable the Mfx

Definition at line 215 of file stm32f4xx_nucleo.c.

References GPIO_PIN, and GPIO_PORT.

void BSP_LED_Init ( Led_TypeDef  Led)

Configures LED GPIO.

Parameters:
Led,:Specifies the Led to be configured. This parameter can be one of following parameters:
  • LED2

Definition at line 190 of file stm32f4xx_nucleo.c.

References GPIO_PIN, GPIO_PORT, and LEDx_GPIO_CLK_ENABLE.

void BSP_LED_Off ( Led_TypeDef  Led)

Turns selected LED Off.

Parameters:
Led,:Specifies the Led to be set off. This parameter can be one of following parameters:
  • LED2

Definition at line 243 of file stm32f4xx_nucleo.c.

References GPIO_PIN, and GPIO_PORT.

void BSP_LED_On ( Led_TypeDef  Led)

Turns selected LED On.

Parameters:
Led,:Specifies the Led to be set on. This parameter can be one of following parameters:
  • LED2

Definition at line 232 of file stm32f4xx_nucleo.c.

References GPIO_PIN, and GPIO_PORT.

void BSP_LED_Toggle ( Led_TypeDef  Led)

Toggles the selected LED.

Parameters:
Led,:Specifies the Led to be toggled. This parameter can be one of following parameters:
  • LED2

Definition at line 254 of file stm32f4xx_nucleo.c.

References GPIO_PIN, and GPIO_PORT.

void BSP_PB_DeInit ( Button_TypeDef  Button)

Push Button DeInit.

Parameters:
Button,:Button to be configured This parameter should be: BUTTON_KEY
Note:
PB DeInit does not disable the GPIO clock

Definition at line 306 of file stm32f4xx_nucleo.c.

References BUTTON_IRQn, BUTTON_PIN, and BUTTON_PORT.

uint32_t BSP_PB_GetState ( Button_TypeDef  Button)

Returns the selected Button state.

Parameters:
Button,:Specifies the Button to be checked. This parameter should be: BUTTON_KEY
Return values:
TheButton GPIO pin value.

Definition at line 321 of file stm32f4xx_nucleo.c.

References BUTTON_PIN, and BUTTON_PORT.

void BSP_PB_Init ( Button_TypeDef  Button,
ButtonMode_TypeDef  ButtonMode 
)

Configures Button GPIO and EXTI Line.

Parameters:
Button,:Specifies the Button to be configured. This parameter should be: BUTTON_KEY
ButtonMode,:Specifies Button mode. This parameter can be one of following parameters:
  • BUTTON_MODE_GPIO: Button will be used as simple IO
  • BUTTON_MODE_EXTI: Button will be connected to EXTI line with interrupt generation capability

Definition at line 269 of file stm32f4xx_nucleo.c.

References BUTTON_IRQn, BUTTON_MODE_EXTI, BUTTON_MODE_GPIO, BUTTON_PIN, BUTTON_PORT, and BUTTONx_GPIO_CLK_ENABLE.

void LCD_Delay ( uint32_t  Delay)

Wait for loop in ms.

Parameters:
Delayin ms.

Definition at line 662 of file stm32f4xx_nucleo.c.

void LCD_IO_WriteData ( uint8_t  Data)

Writes data to select the LCD register.

This function must be used after st7735_WriteReg() function

Parameters:
Data,:data to write to the selected register.

Definition at line 588 of file stm32f4xx_nucleo.c.

References LCD_CS_HIGH, LCD_CS_LOW, LCD_DC_HIGH, and SPIx_Write().

void LCD_IO_WriteMultipleData ( uint8_t *  pData,
uint32_t  Size 
)

Writes register value.

Parameters:
pData,:Pointer on the register value
Size,:Size of byte to transmit to the register

Definition at line 608 of file stm32f4xx_nucleo.c.

References hnucleo_Spi, LCD_CS_HIGH, LCD_CS_LOW, LCD_DC_HIGH, and SPIx_Write().

void LCD_IO_WriteReg ( uint8_t  LCDReg)

Writes command to select the LCD register.

Parameters:
LCDReg,:Address of the selected register.

Definition at line 568 of file stm32f4xx_nucleo.c.

References LCD_CS_HIGH, LCD_CS_LOW, LCD_DC_LOW, and SPIx_Write().

void SD_IO_CSState ( uint8_t  val)

Set the SD_CS pin.

Parameters:
val,:pin value.

Definition at line 498 of file stm32f4xx_nucleo.c.

References SD_CS_HIGH, and SD_CS_LOW.

uint8_t SD_IO_WriteByte ( uint8_t  Data)

Writes a byte on the SD.

Parameters:
Data,:byte to send.

Definition at line 526 of file stm32f4xx_nucleo.c.

References SPIx_WriteReadData().

Referenced by SD_IO_Init().

void SD_IO_WriteReadData ( const uint8_t *  DataIn,
uint8_t *  DataOut,
uint16_t  DataLength 
)

Write a byte on the SD.

Parameters:
DataIn,:value to be written
DataOut,:value to be read
DataLength,:length of data

Definition at line 516 of file stm32f4xx_nucleo.c.

References SPIx_WriteReadData().

static void SPIx_Write ( uint8_t  Value) [static]

SPI Write a byte to device.

Parameters:
Value,:value to be written

Definition at line 427 of file stm32f4xx_nucleo.c.

References hnucleo_Spi, SPIx_Error(), and SpixTimeout.

Referenced by LCD_IO_WriteData(), LCD_IO_WriteMultipleData(), and LCD_IO_WriteReg().

static void SPIx_WriteReadData ( const uint8_t *  DataIn,
uint8_t *  DataOut,
uint16_t  DataLegnth 
) [static]

SPI Write a byte to device.

Parameters:
DataIn,:value to be written
DataOut,:value to be read
DataLegnth,:length of data

Definition at line 409 of file stm32f4xx_nucleo.c.

References hnucleo_Spi, SPIx_Error(), and SpixTimeout.

Referenced by SD_IO_WriteByte(), and SD_IO_WriteReadData().

Generated on Tue Jan 12 2016 13:17:23 for STM32F4xx_Nucleo BSP User Manual by   doxygen 1.7.6.1