IMAQ Occurrence Config2 VI

NI-IMAQ VI

IMAQ Occurrence Config2 VI

Installed With: NI Vision Acquisition Software

Creates occurrences that are set by image acquisition signals such as the assertion of a status or trigger signal. Occurrences produced by this VI are used as inputs to the Wait on Occurrence LabVIEW primitive. Anything dependent on the execution of the Wait on Occurrence primitive will wait until the occurrence is set.

IMAQ Occurrence Config2

cu32.gif

Signal polarity specifies the polarity of the status or trigger signal parameter.

The following values are valid:

Rising Edge (0)

Sets the signal polarity to rising edge.

Falling Edge (1)

Sets the signal polarity to falling edge.

crn.gif

IMAQ Session In identifies the device.

cu32.gif

Signal Type specifies the type of signal that causes the occurrence to be set.

The following values are valid:

Note  To use the ISO_IN or RS422_In signals on the NI PCI-1426, select External as the Trigger Type for your function and select either ISO In or RS-422 In as the Signal Level in Measurement & Automation Explorer (MAX).
External (0)

Specifies the signal type as the external trigger lines.

RTSI (1)

Specifies the signal type as the RTSI trigger lines.

ISO In (2)

Specifies the signal type as the isolated input trigger lines.

ISO Out (3)

Specifies the signal type as the isolated output trigger lines.

Status (4)

Specifies the signal type as one of the Status Signal signals.

cu32.gif

Status Signal Signal specifies the signal that causes the occurrence to be set if Signal Type is set to Status.

The following values are valid:

Note  The Frame start and Frame done signals are not valid for line scan acquisitions unless each buffer is triggered.
Acquisition in progress (15)

Asserts when the acquisition begins.

Acquisition done (8)

Asserts when the entire acquisition is finished.

Frame start (9)

Asserts at the beginning of each frame that is captured.

Frame done (10)

Asserts at the end of each frame that is captured.

Buffer Complete (11)

Asserts when a buffer has been transferred to memory.

cu32.gif

Signal Number specifies the number of the trigger line that causes the occurrence to be set if Signal Type is set to one of the trigger types.

cerrcodeclst.gif

error in (no error) describes error conditions that occur before this VI or function runs. The default is no error. If an error occurred before this VI or function runs, the VI or function passes the error in value to error out. This VI or function runs normally only if no error occurred before this VI or function runs. If an error occurs while this VI or function runs, it runs normally and sets its own error status in error out. Use the Simple Error Handler or General Error Handler VIs to display the description of the error code. Use error in and error out to check errors and to specify execution order by wiring error out from one node to error in of the next node.

cbool.gif

status is TRUE (X) if an error occurred before this VI or function ran or FALSE (checkmark) to indicate a warning or that no error occurred before this VI or function ran. The default is FALSE.

ci32.gif

code code is the number identifying an error or warning. If status is TRUE, code is a non-zero error code. If status is FALSE, code can be zero or a warning code. Use the error handler VIs to look up the meaning of this code and to display the corresponding error message.

cstr.gif

source describes the origin of the error or warning and is, in most cases, the name of the VI or function that produced the error or warning. The default is an empty string.

cu16.gif

create/clear instructs the VI to create an occurrence or to clear all occurrences that have been created for the image acquisition device specified in IMAQ Session In.

The following values are valid:

create an occurrence (0)

Creates an occurrence.

clear all occurrences (1)

Clears all occurrences.

cbool.gif

Rearm? (FALSE : No Rearm) indicates whether the occurrence should be generated once, or each time the signal occurs. When you set this parameter to TRUE, call this VI again with the create/clear parameter set to clear all occurrences to stop the occurrence.

irn.gif

IMAQ Session Out has the same value as IMAQ Session In.

irn.gif

occurrence is the occurrence value created. Wire this output to a Wait on Occurrence LabVIEW primitive. Wire the output of the primitive to the part of your diagram you wish to execute when an event happens and the occurrence is set.

ierrcodeclst.gif

error out contains error information. If error in indicates that an error occurred before this VI or function ran, error out contains the same error information. Otherwise, it describes the error status that this VI or function produces. Right-click the error out indicator on the front panel and select Explain Error from the shortcut menu for more information about the error.

ibool.gif

status is TRUE (X) if an error occurred or FALSE (checkmark) to indicate a warning or that no error occurred.

ii32.gif

code is the error or warning code. If status is TRUE, code is a nonzero error code. If status is FALSE, code is 0 or a warning code.

istr.gif

source describes the origin of the error or warning and is, in most cases, the name of the VI or function that produced the error or warning. The default is an empty string.